Mahmoud Reza Ghandehari Ferdowsi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mahmoud Reza Ghandehari Ferdowsi has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Mazinani
Ferdowsi University of Mashhad
5 shared publications - Gholam Reza Ebrahimi
Department of Materials Science and Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
4 shared publications - Davood Nakhaie
Department of Materials Engineering, The University of British Columbia, Vancouver, BC V6T 1Z4, Canada
2 shared publications - Jun Wang
Institute for Frontier Materials, Deakin University, Geelong, Australia
2 shared publications Matthew R. Barnett
2 shared publicationsMinoo Naebe
2 shared publications
Latest Publications
- Open Access
- 7 December 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 28, 546-559
Hybrid heterophasic polypropylene composites with basalt fibers and Magnesium oxysulfate reinforcements for sustainable automotive materials
- 7 December 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 28, 546-559
Open AccessHybrid heterophasic polypropylene composites with basalt fibers and Magnesium oxysulfate reinforcements for sustainable automotive materials
- 1 February 2019
- Published by Elsevier in Scripta Materialia
- Vol. 160, 5-8
Influence of precipitation on yield elongation in Mg-Zn alloys
- 1 February 2019
- Published by Elsevier in Scripta Materialia
- Vol. 160, 5-8
Influence of precipitation on yield elongation in Mg-Zn alloys
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 1579-1584
In Situ Synchrotron Analysis of Twinning Stresses in an Aged Mg-4.5Zn Alloy
Aging increases the yield strength of aged Mg-Zn alloys. The effect of aging on the stress required for twinning is examined using in-situ transmission based synchrotron X-ray diffraction. The as extruded material was aged at variety of temperatures for different times. It is found that increasing sample diameter (thickness) results in peak broadening. The data are analysed to establish the evolution of twin volume fraction with stress. Results indicated an increase in twinning stress at 10% twin volume fraction in aged samples in comparison with non-aged condition. The investigation showed a strong relation between the macroscopic yield stress and the twinning stress (at 10% twin volume fraction).
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 1579-1584
In Situ Synchrotron Analysis of Twinning Stresses in an Aged Mg-4.5Zn Alloy
Aging increases the yield strength of aged Mg-Zn alloys. The effect of aging on the stress required for twinning is examined using in-situ transmission based synchrotron X-ray diffraction. The as extruded material was aged at variety of temperatures for different times. It is found that increasing sample diameter (thickness) results in peak broadening. The data are analysed to establish the evolution of twin volume fraction with stress. Results indicated an increase in twinning stress at 10% twin volume fraction in aged samples in comparison with non-aged condition. The investigation showed a strong relation between the macroscopic yield stress and the twinning stress (at 10% twin volume fraction).
- 16 November 2014
- Published by Springer Nature in Metals and Materials International
- Vol. 20 (6) , 1073-1083
Strain-dependent constitutive modelling of AZ80 magnesium alloy containing 0.5 wt% rare earth elements and evaluation of its validation using finite element method
- 16 November 2014
- Published by Springer Nature in Metals and Materials International
- Vol. 20 (6) , 1073-1083
Strain-dependent constitutive modelling of AZ80 magnesium alloy containing 0.5 wt% rare earth elements and evaluation of its validation using finite element method
- 1 June 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 606, 214-227
Effects of hot rolling and inter-stage annealing on the microstructure and texture evolution in a partially homogenized AZ91 magnesium alloy
- 1 June 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 606, 214-227
Effects of hot rolling and inter-stage annealing on the microstructure and texture evolution in a partially homogenized AZ91 magnesium alloy
- 7 December 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (3) , 1077-1087
Modeling the High Temperature Flow Behavior and Dynamic Recrystallization Kinetics of a Medium Carbon Microalloyed Steel
- 7 December 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (3) , 1077-1087
Modeling the High Temperature Flow Behavior and Dynamic Recrystallization Kinetics of a Medium Carbon Microalloyed Steel
- 1 December 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 626, 445-448
Microstructural Evolution in Partially Homogenized AZ91 Alloy during Hot Rolling and Interpass Annealing
The as-cast AZ91 Mg alloy ingot with mean grain size of 98 μm after solution treatment was subjected to plastic deformation by multi-pass hot rolling. The process facilitated steady grain refinement by dynamic recrystallization with increasing rolling passes, and the final grain size was reduced to 6.4 μm by 4 rolling passes. Optical microscopy demonstrated that in the beginning of the rolling process twin DRX was the major dynamic recrystallization mechanism. In contrast, in 3rd and 4th passes of rolling new grains nucleated at grain boundaries, due to low grain size of the alloy.
- 1 December 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 626, 445-448
Microstructural Evolution in Partially Homogenized AZ91 Alloy during Hot Rolling and Interpass Annealing
The as-cast AZ91 Mg alloy ingot with mean grain size of 98 μm after solution treatment was subjected to plastic deformation by multi-pass hot rolling. The process facilitated steady grain refinement by dynamic recrystallization with increasing rolling passes, and the final grain size was reduced to 6.4 μm by 4 rolling passes. Optical microscopy demonstrated that in the beginning of the rolling process twin DRX was the major dynamic recrystallization mechanism. In contrast, in 3rd and 4th passes of rolling new grains nucleated at grain boundaries, due to low grain size of the alloy.
- 7 August 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 43 (13) , 5209-5217
Controlled Forging of a Nb Containing Microalloyed Steel for Automotive Applications
- 7 August 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 43 (13) , 5209-5217
Controlled Forging of a Nb Containing Microalloyed Steel for Automotive Applications
- 29 November 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 409, 835-840
Thermomechanical Processing of a Nb-Microalloyed Steel in a Controlled-Forging Treatment
Ferrite grain size is one of the most important microstructural parameters in steels which can be appropriately adjusted to cause a significant strengthening effect. Thermomechanical processing is an effective method for ferrite grain refinement in microalloyed steels. Transformation of deformed austenite with a pancaked grain structure to a relatively fine ferrite phase is an important phenomenon occurring during the thermomechanical processing of microalloyed steels. The final microstructure of steels can be optimized by controlling three critical processing parameters, i.e. i) applied strain (constant strain rate), ii) deformation temperature, and iii) cooling rates following the hot deformation stage. In the present study, a new approach (called controlled-forging treatment) consisting of hot deformation of steel at the austenitic temperature range using an upset forging stage was developed for the ferrite grain refinement in a Nb-microalloyed steel. The investigated steel was subjected to a thermomechanical treatment including reheating, hot deformation for two different strain levels, namely 30 and 50% reductions of height, in a single pass hot-forging stage at temperatures below the TNR (no-recrystallization) and above the TR3 (austenite to ferrite transformation) temperatures followed by cooling to room temperature using three different cooling rates. The experimental results obtained from this proposed treatment were more or less similar to those already obtained for the case of controlled-rolling process on Nb-microalloyed steel sheets.
- 29 November 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 409, 835-840
Thermomechanical Processing of a Nb-Microalloyed Steel in a Controlled-Forging Treatment
Ferrite grain size is one of the most important microstructural parameters in steels which can be appropriately adjusted to cause a significant strengthening effect. Thermomechanical processing is an effective method for ferrite grain refinement in microalloyed steels. Transformation of deformed austenite with a pancaked grain structure to a relatively fine ferrite phase is an important phenomenon occurring during the thermomechanical processing of microalloyed steels. The final microstructure of steels can be optimized by controlling three critical processing parameters, i.e. i) applied strain (constant strain rate), ii) deformation temperature, and iii) cooling rates following the hot deformation stage. In the present study, a new approach (called controlled-forging treatment) consisting of hot deformation of steel at the austenitic temperature range using an upset forging stage was developed for the ferrite grain refinement in a Nb-microalloyed steel. The investigated steel was subjected to a thermomechanical treatment including reheating, hot deformation for two different strain levels, namely 30 and 50% reductions of height, in a single pass hot-forging stage at temperatures below the TNR (no-recrystallization) and above the TR3 (austenite to ferrite transformation) temperatures followed by cooling to room temperature using three different cooling rates. The experimental results obtained from this proposed treatment were more or less similar to those already obtained for the case of controlled-rolling process on Nb-microalloyed steel sheets.