Michael E. Dreyer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Michael E. Dreyer has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
A. Grah
European Commission, Institute for Energy and Transport, Petten, The Netherlands
2 shared publicationsM. M. Weislogel
Department of Mechanical and Materials Engineering, Portland State University, PO Box 751, Portland, Oregon 97207, USA
2 shared publicationsP. M. Bronowicki
Center of Applied Space Technology and Microgravity (ZARM), University of Bremen, Am Fallturm 01, 28359 Bremen, Germany
2 shared publications- Prithvi Shukla
Department of Fluid Mechanics, Faculty of Production Engineering - Mechanical Engineering and Process Engineering, University of Bremen, Center of Applied Space Technology and Microgravity (ZARM), Bremen, Germany
2 shared publications - André Pingel
Faculty of Production Engineering - Mechanical Engineering and Process Engineering, Department of Fluid Mechanics, Center of Applied Space Technology and Microgravity (ZARM), University of Bremen, Bremen, Germany
1 shared publication - Diana Gaulke
ZARM University Bremen, Am Fallturm
1 shared publication
Latest Publications
- Open Access
- 22 January 2024
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 36 (1) , 1-23
Phase Separation through Screen Channel Liquid Acquisition Devices in Microgravity
To enable future deep space exploration, orbital refueling of spacecraft is essential. However, transferring liquid in a microgravity environment is a complex process dependent on various factors. One of the basic and critical tasks is to separate phases to allow the supply of gas-free liquid from one tank to another. For this purpose, a liquid acquisition device is essential. In this work, a screen channel liquid acquisition device was designed and used to investigate phase separation and liquid removal from an experiment tank in a microgravity environment. The experiments were performed using the drop tower facility at the University of Bremen, with HFE-7500 as the test liquid under isothermal conditions. This investigation explored the interdependent effects of various phenomena, including the reorientation of liquid in the tank, capillary rise between parallel plates, flow through screen pressure variation, and bubble point breakthrough. Under subcritical conditions, the SC-LAD was found to supply gas-free liquid at the outlet, as long as the pressure drop across the screen was lower than the bubble point threshold. At the critical point, the screen started to ingest bubbles, resulting in a sharp peak in the differential pressure signal. The wetted area of the screen was obtained by analyzing images captured with a high-speed camera and used to calculate the analytical pressure drop. The experimental results were compared with the analytical solution and discussed in detail.
- 22 January 2024
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 36 (1) , 1-23
Open AccessPhase Separation through Screen Channel Liquid Acquisition Devices in Microgravity
To enable future deep space exploration, orbital refueling of spacecraft is essential. However, transferring liquid in a microgravity environment is a complex process dependent on various factors. One of the basic and critical tasks is to separate phases to allow the supply of gas-free liquid from one tank to another. For this purpose, a liquid acquisition device is essential. In this work, a screen channel liquid acquisition device was designed and used to investigate phase separation and liquid removal from an experiment tank in a microgravity environment. The experiments were performed using the drop tower facility at the University of Bremen, with HFE-7500 as the test liquid under isothermal conditions. This investigation explored the interdependent effects of various phenomena, including the reorientation of liquid in the tank, capillary rise between parallel plates, flow through screen pressure variation, and bubble point breakthrough. Under subcritical conditions, the SC-LAD was found to supply gas-free liquid at the outlet, as long as the pressure drop across the screen was lower than the bubble point threshold. At the critical point, the screen started to ingest bubbles, resulting in a sharp peak in the differential pressure signal. The wetted area of the screen was obtained by analyzing images captured with a high-speed camera and used to calculate the analytical pressure drop. The experimental results were compared with the analytical solution and discussed in detail.
- Open Access
- 29 April 2023
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 35 (3) , 1-23
Experimental Investigation of Liquid Interface Stability During the Filling of a Tank in Microgravity
The storage of propellants in space as well as the transfer and filling of spacecraft tanks is a prerequisite for future long-term space exploration missions. In this work, the vented filling of a partially filled tank, which is envisioned as a spacecraft tank, was investigated experimentally under compensated gravity in the Bremen Drop Tower. Experiments were performed with a partially filled tank and a test liquid HFE-7500. The drop tower provides 9 s of compensated gravity. The shape of the free liquid surface inside a right circular cylinder changes from the normal gravity configuration to a free fall configuration during the test. The filling was initiated after 3.5 s and continued until the end at 9 s. The interaction of the incoming liquid jet with the liquid interface was studied for different volumetric flow rates. A stable, but not steady liquid interface was characterized by a deformation due to the incoming liquid jet and the formation of a geyser. The growth of the geyser and the following disintegration into liquid droplets indicated an unstable liquid interface. Subcritical, critical and supercritical regimes of the volumetric flow rates were identified to classify stable and unstable liquid interfaces. The critical Weber number was found to be 1.04, which corresponds to a critical volumetric flow rate of 1.30 mL s-1. This critical Weber number was compared with the existing literature. Additionally, the behaviour of the liquid interface during the reorientation of the liquid inside the tank was observed.
- 29 April 2023
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 35 (3) , 1-23
Open AccessExperimental Investigation of Liquid Interface Stability During the Filling of a Tank in Microgravity
The storage of propellants in space as well as the transfer and filling of spacecraft tanks is a prerequisite for future long-term space exploration missions. In this work, the vented filling of a partially filled tank, which is envisioned as a spacecraft tank, was investigated experimentally under compensated gravity in the Bremen Drop Tower. Experiments were performed with a partially filled tank and a test liquid HFE-7500. The drop tower provides 9 s of compensated gravity. The shape of the free liquid surface inside a right circular cylinder changes from the normal gravity configuration to a free fall configuration during the test. The filling was initiated after 3.5 s and continued until the end at 9 s. The interaction of the incoming liquid jet with the liquid interface was studied for different volumetric flow rates. A stable, but not steady liquid interface was characterized by a deformation due to the incoming liquid jet and the formation of a geyser. The growth of the geyser and the following disintegration into liquid droplets indicated an unstable liquid interface. Subcritical, critical and supercritical regimes of the volumetric flow rates were identified to classify stable and unstable liquid interfaces. The critical Weber number was found to be 1.04, which corresponds to a critical volumetric flow rate of 1.30 mL s-1. This critical Weber number was compared with the existing literature. Additionally, the behaviour of the liquid interface during the reorientation of the liquid inside the tank was observed.
- Open Access
SiOC Screens with Aligned and Adjustable Pore Structure for Screen Channel Liquid Acquisition Device
The development of porous ceramic screens with high chemical stability, low density, and thermal conductivity can lead to promising screen channel liquid acquisition devices (SC-LADs) for propellant management under microgravity conditions in the future. Therefore, SiOC screens with aligned pores were fabricated via freeze-casting and applied as a SC-LAD. The pore window sizes and open porosity varied from 6 µm to 43 µm and 65% or 79%, depending on the freezing temperature or the solid loading, respectively. The pore window size distributions and bubble point tests indicate crack-free screens. On the one hand, SC-LADs with an open porosity of 79% removed gas-free liquid up to a volumetric flow rate of 4 mL s−1. On the other hand, SC-LADs with an open porosity of 65% were limited to 2 mL s−1 as the pressure drop across these screens was relatively higher. SC-LADs with the same open porosity but smaller pore window sizes showed a higher pressure drop across the screen and bubble ingestion at higher values of effective screen area when increasing the applied removal volumetric flow rate. The removed liquid from the SC-LADs was particle-free, thus representing a potential for applications in a harsh chemical environment or broad-range temperatures.
Open AccessSiOC Screens with Aligned and Adjustable Pore Structure for Screen Channel Liquid Acquisition Device
The development of porous ceramic screens with high chemical stability, low density, and thermal conductivity can lead to promising screen channel liquid acquisition devices (SC-LADs) for propellant management under microgravity conditions in the future. Therefore, SiOC screens with aligned pores were fabricated via freeze-casting and applied as a SC-LAD. The pore window sizes and open porosity varied from 6 µm to 43 µm and 65% or 79%, depending on the freezing temperature or the solid loading, respectively. The pore window size distributions and bubble point tests indicate crack-free screens. On the one hand, SC-LADs with an open porosity of 79% removed gas-free liquid up to a volumetric flow rate of 4 mL s−1. On the other hand, SC-LADs with an open porosity of 65% were limited to 2 mL s−1 as the pressure drop across these screens was relatively higher. SC-LADs with the same open porosity but smaller pore window sizes showed a higher pressure drop across the screen and bubble ingestion at higher values of effective screen area when increasing the applied removal volumetric flow rate. The removed liquid from the SC-LADs was particle-free, thus representing a potential for applications in a harsh chemical environment or broad-range temperatures.
- Open Access
- 9 November 2020
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 32 (6) , 1001-1018
Phase Separation in Porous Media Integrated Capillary Channels
Phase separation in space is critical for gas-free propellant supply, life support systems, refueling of spacecraft in low earth orbit (LEO), and for deep space exploration missions. In the absence of gravity, the stability of the liquid-gas interface depends on capillary forces. High liquid flow rates, sudden accelerations, and vibrational disturbances can cause the free surface of the liquid to collapse, which results in the ingestion of gas. Propellant tanks may have screen channel liquid acquisition devices (SCLADs) to position and maintain a gas-free propellant supply to the outlet. A saturated porous screen permits liquid to pass through but acts as a barrier to the gas. We investigated phase separation in porous media integrated capillary channels during parabolic flights (33rd DLR parabolic flight campaign in March 2019). An open side of a rectangular channel was covered with a dutch twill weave 200×1400. The liquid was ingested into the channel from its surroundings by establishing a differential pressure across the screen section. The gas-phase was blocked during the liquid withdrawal. We could show that the gas breakthrough occurs when the pressure difference across the screen exceeds the bubble point pressure. The experimental results showed good agreement with correlations from literature.
- 9 November 2020
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 32 (6) , 1001-1018
Open AccessPhase Separation in Porous Media Integrated Capillary Channels
Phase separation in space is critical for gas-free propellant supply, life support systems, refueling of spacecraft in low earth orbit (LEO), and for deep space exploration missions. In the absence of gravity, the stability of the liquid-gas interface depends on capillary forces. High liquid flow rates, sudden accelerations, and vibrational disturbances can cause the free surface of the liquid to collapse, which results in the ingestion of gas. Propellant tanks may have screen channel liquid acquisition devices (SCLADs) to position and maintain a gas-free propellant supply to the outlet. A saturated porous screen permits liquid to pass through but acts as a barrier to the gas. We investigated phase separation in porous media integrated capillary channels during parabolic flights (33rd DLR parabolic flight campaign in March 2019). An open side of a rectangular channel was covered with a dutch twill weave 200×1400. The liquid was ingested into the channel from its surroundings by establishing a differential pressure across the screen section. The gas-phase was blocked during the liquid withdrawal. We could show that the gas breakthrough occurs when the pressure difference across the screen exceeds the bubble point pressure. The experimental results showed good agreement with correlations from literature.
- 1 October 2019
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 31 (5) , 649-671
Phase Separation of Liquid from Gaseous Hydrogen in Microgravity Experimental Results
- 1 October 2019
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 31 (5) , 649-671
Phase Separation of Liquid from Gaseous Hydrogen in Microgravity Experimental Results
- 1 July 2015
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 27 (4) , 261-271
CFD Simulation of Capillary Transport of Liquid Between Parallel Perforated Plates using Flow3D
- 1 July 2015
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 27 (4) , 261-271
CFD Simulation of Capillary Transport of Liquid Between Parallel Perforated Plates using Flow3D
- 9 June 2015
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 52 (4) , 855-876
Free surface deformation and heat transfer by thermocapillary convection
- 9 June 2015
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 52 (4) , 855-876
Free surface deformation and heat transfer by thermocapillary convection
- 10 December 2013
- Published by American Physical Society (APS) in Physical Review E
- Vol. 88 (6) , 063009
Capillary channel flow experiments aboard the International Space Station
In the near-weightless environment of orbiting spacecraft capillary forces dominate interfacial flow phenomena over unearthly large length scales. In current experiments aboard the International Space Station, partially open channels are being investigated to determine critical flow rate-limiting conditions above which the free surface collapses ingesting bubbles. Without the natural passive phase separating qualities of buoyancy, such ingested bubbles can in turn wreak havoc on the fluid transport systems of spacecraft. The flow channels under investigation represent geometric families of conduits with applications to liquid propellant acquisition, thermal fluids circulation, and water processing for life support. Present and near future experiments focus on transient phenomena and conduit asymmetries allowing capillary forces to replace the role of gravity to perform passive phase separations. Terrestrial applications are noted where enhanced transport via direct liquid-gas contact is desired.
- 10 December 2013
- Published by American Physical Society (APS) in Physical Review E
- Vol. 88 (6) , 063009
Capillary channel flow experiments aboard the International Space Station
In the near-weightless environment of orbiting spacecraft capillary forces dominate interfacial flow phenomena over unearthly large length scales. In current experiments aboard the International Space Station, partially open channels are being investigated to determine critical flow rate-limiting conditions above which the free surface collapses ingesting bubbles. Without the natural passive phase separating qualities of buoyancy, such ingested bubbles can in turn wreak havoc on the fluid transport systems of spacecraft. The flow channels under investigation represent geometric families of conduits with applications to liquid propellant acquisition, thermal fluids circulation, and water processing for life support. Present and near future experiments focus on transient phenomena and conduit asymmetries allowing capillary forces to replace the role of gravity to perform passive phase separations. Terrestrial applications are noted where enhanced transport via direct liquid-gas contact is desired.
- 8 May 2013
- Published by Springer Nature in Experiments in Fluids
- Vol. 54 (5) , 1-14
The capillary channel flow experiments on the International Space Station: experiment set-up and first results
- 8 May 2013
- Published by Springer Nature in Experiments in Fluids
- Vol. 54 (5) , 1-14
The capillary channel flow experiments on the International Space Station: experiment set-up and first results
- 25 September 2010
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 22 (4) , 463-474
Drop Tower Experiments on Non-isothermal Reorientation of Cryogenic Liquids
- 25 September 2010
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 22 (4) , 463-474
Drop Tower Experiments on Non-isothermal Reorientation of Cryogenic Liquids