Rui Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Rui Huang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Bo Huang
Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences , 518055 Shenzhen , China
3 shared publicationsShusheng Zhang
Northwestern Polytechnical University
3 shared publicationsChanghong Xu
The Key Laboratory of Contemporary Designing and Integrated Manufacturing Technology, Ministry of Education, Northwestern Polytechnical University, Xi׳an 710072, China
2 shared publicationsChen Zhengming
College of IoT Engineering, Hohai University, Changzhou, China
1 shared publicationHaiTao Fan
Northwest Polytechnical University
1 shared publicationHe Kunjin
College of IoT Engineering, Hohai University, Changzhou, China
1 shared publication
Latest Publications
- Open Access
- 6 March 2024
- Published by Oxford University Press (OUP) in Journal of Computational Design and Engineering
- Vol. 11 (2) , 161-175
Combining active learning and self-paced learning for cost-effective process design intents extraction of process data
With the widespread use of computer-aided technologies like CAD/CAM/CAPP in the product manufacturing process, a large amount of process data is constantly generated and data-driven process planning has shown promising potentials for effectively reusing the process knowledge. However, a lot of labeled data are needed to train a deep learning model for effectively extracting the embedded knowledge and experiences within these process data and the labeling of process data is quite expensive and time-consuming. This paper proposes a cost-effective process design intents extraction approach for process data by combining active learning (AL) and self-paced learning (SPL). First, the process design intents inference model based on Bi-LSTM is generated by using a few pre-labeled samples. Then, the prediction uncertainty of each unlabeled sample is calculated by using a Bayesian neural network, which can assist in the identification of high confidence samples in SPL and low confidence samples in AL. Finally, the low confidence samples with manual-labels and the high confidence samples with pseudo-labels are incorporated into the training data for retraining the process design intents inference model iteratively until the model attains optimal performance. The experiments demonstrate that our approach can substantially decrease the number of labeled samples required for model training and the design intents in the process data could be inferred effectively with dynamically undated training data.
- 6 March 2024
- Published by Oxford University Press (OUP) in Journal of Computational Design and Engineering
- Vol. 11 (2) , 161-175
Open AccessCombining active learning and self-paced learning for cost-effective process design intents extraction of process data
With the widespread use of computer-aided technologies like CAD/CAM/CAPP in the product manufacturing process, a large amount of process data is constantly generated and data-driven process planning has shown promising potentials for effectively reusing the process knowledge. However, a lot of labeled data are needed to train a deep learning model for effectively extracting the embedded knowledge and experiences within these process data and the labeling of process data is quite expensive and time-consuming. This paper proposes a cost-effective process design intents extraction approach for process data by combining active learning (AL) and self-paced learning (SPL). First, the process design intents inference model based on Bi-LSTM is generated by using a few pre-labeled samples. Then, the prediction uncertainty of each unlabeled sample is calculated by using a Bayesian neural network, which can assist in the identification of high confidence samples in SPL and low confidence samples in AL. Finally, the low confidence samples with manual-labels and the high confidence samples with pseudo-labels are incorporated into the training data for retraining the process design intents inference model iteratively until the model attains optimal performance. The experiments demonstrate that our approach can substantially decrease the number of labeled samples required for model training and the design intents in the process data could be inferred effectively with dynamically undated training data.
- 25 June 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (5-8) , 2045-2060
Multilevel structured NC machining process model based on dynamic machining feature for process reuse
- 25 June 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (5-8) , 2045-2060
Multilevel structured NC machining process model based on dynamic machining feature for process reuse
- 3 March 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (9-12) , 3279-3293
An effective adaptive dynamic evolution computing approach of roughing process for part with complex pockets
- 3 March 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (9-12) , 3279-3293
An effective adaptive dynamic evolution computing approach of roughing process for part with complex pockets
- 14 February 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 91 (9-12) , 4341-4358
An effective freeform surface retrieval approach for potential machining process reuse
- 14 February 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 91 (9-12) , 4341-4358
An effective freeform surface retrieval approach for potential machining process reuse
- Open Access
- 23 June 2015
- Published by Oxford University Press (OUP) in Journal of Computational Design and Engineering
- Vol. 2 (4) , 253-260
An automatic 3D CAD model errors detection method of aircraft structural part for NC machining
Feature-based NC machining, which requires high quality of 3D CAD model, is widely used in machining aircraft structural part. However, there has been little research on how to automatically detect the CAD model errors. As a result, the user has to manually check the errors with great effort before NC programming. This paper proposes an automatic CAD model errors detection approach for aircraft structural part. First, the base faces are identified based on the reference directions corresponding to machining coordinate systems. Then, the CAD models are partitioned into multiple local regions based on the base faces. Finally, the CAD model error types are evaluated based on the heuristic rules. A prototype system based on CATIA has been developed to verify the effectiveness of the proposed approach. Highlights The 3D CAD model of an aircraft structural part is partitioned into multiple local regions in terms of the base faces. The fillet association level graph is proposed to represent the local region for exploring the CAD model errors. An automatic CAD model error detection method based on heuristics rule is proposed.
- 23 June 2015
- Published by Oxford University Press (OUP) in Journal of Computational Design and Engineering
- Vol. 2 (4) , 253-260
Open AccessAn automatic 3D CAD model errors detection method of aircraft structural part for NC machining
Feature-based NC machining, which requires high quality of 3D CAD model, is widely used in machining aircraft structural part. However, there has been little research on how to automatically detect the CAD model errors. As a result, the user has to manually check the errors with great effort before NC programming. This paper proposes an automatic CAD model errors detection approach for aircraft structural part. First, the base faces are identified based on the reference directions corresponding to machining coordinate systems. Then, the CAD models are partitioned into multiple local regions based on the base faces. Finally, the CAD model error types are evaluated based on the heuristic rules. A prototype system based on CATIA has been developed to verify the effectiveness of the proposed approach. Highlights The 3D CAD model of an aircraft structural part is partitioned into multiple local regions in terms of the base faces. The fillet association level graph is proposed to represent the local region for exploring the CAD model errors. An automatic CAD model error detection method based on heuristics rule is proposed.
- 9 August 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 75 (5-8) , 1035-1048
Multi-level structuralized model-based definition model based on machining features for manufacturing reuse of mechanical parts
- 9 August 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 75 (5-8) , 1035-1048
Multi-level structuralized model-based definition model based on machining features for manufacturing reuse of mechanical parts
- 25 April 2011
- Published by Springer Nature in Science China Technological Sciences
- Vol. 54 (7) , 1826-1832
A matching algorithm between precursory 3D process model and 2D working procedure drawing based on subgraph isomorphism
- 25 April 2011
- Published by Springer Nature in Science China Technological Sciences
- Vol. 54 (7) , 1826-1832
A matching algorithm between precursory 3D process model and 2D working procedure drawing based on subgraph isomorphism