Saleh Kaytbay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Saleh Kaytbay has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Medhat Awad El-Hadek
Port Said University
2 shared publications - Abdalla Ahmed
Department of Mechanical Engineering, Faculty of Engineering at Benha, Benha University, Qalyubia, Egypt
1 shared publication Abdelmoty Elhakeem
Benha University
1 shared publication- Amr Osman
Department of Mechanical Engineering, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong 999077, China
1 shared publication
Latest Publications
- 1 June 2020
- Published by Trans Tech Publications, Ltd. in Nano Hybrids and Composites
- Vol. 29, 51-60
Influence of Different Nano-Structured Fillers on the Performance of Epoxy Nanocomposites
Nowadays, multi-functional materials are strongly needed to meet the requirements of next-generation electronic devices. In this work, two different nanostructured fillers, reduced graphene oxide (RGO) and nanoalumina, were chosen to study their effect on the thermal, electrical and mechanical properties of the prepared epoxy composites at different loadings (0.5 to 2 wt%). RGO was firstly prepared and characterized by XRD, Raman spectroscopy and TEM confirming its production. The results revealed that RGO showed excellent adhesion with the polymer. Whilst, alumina aggregated and debonded from the matrix, as confirmed by SEM images. Hence, at only 2 wt%, RGO/epoxy composites exhibited the highest thermal conductivity (0.391 W/m-K), which was 1.96 times higher than the neat epoxy. Whereas, the alumina/epoxy composites showed lower increment at the same loading (0.206 W/m-K). However, at 2 wt% RGO, electrical percolation networks had been formed across the matrix (DC conductivity = 2×10-7 S/cm). While, epoxy filled with alumina remained insulative at any loading (~ 10-12 S/cm at 100 Hz). Besides, the tensile strength of the composites was improved by 75% and 37% when filled with 0.5 wt% RGO and alumina, respectively. These results are very useful for preparing multi-functional polymeric materials, which are critically required for packaging industries.
- 1 June 2020
- Published by Trans Tech Publications, Ltd. in Nano Hybrids and Composites
- Vol. 29, 51-60
Influence of Different Nano-Structured Fillers on the Performance of Epoxy Nanocomposites
Nowadays, multi-functional materials are strongly needed to meet the requirements of next-generation electronic devices. In this work, two different nanostructured fillers, reduced graphene oxide (RGO) and nanoalumina, were chosen to study their effect on the thermal, electrical and mechanical properties of the prepared epoxy composites at different loadings (0.5 to 2 wt%). RGO was firstly prepared and characterized by XRD, Raman spectroscopy and TEM confirming its production. The results revealed that RGO showed excellent adhesion with the polymer. Whilst, alumina aggregated and debonded from the matrix, as confirmed by SEM images. Hence, at only 2 wt%, RGO/epoxy composites exhibited the highest thermal conductivity (0.391 W/m-K), which was 1.96 times higher than the neat epoxy. Whereas, the alumina/epoxy composites showed lower increment at the same loading (0.206 W/m-K). However, at 2 wt% RGO, electrical percolation networks had been formed across the matrix (DC conductivity = 2×10-7 S/cm). While, epoxy filled with alumina remained insulative at any loading (~ 10-12 S/cm at 100 Hz). Besides, the tensile strength of the composites was improved by 75% and 37% when filled with 0.5 wt% RGO and alumina, respectively. These results are very useful for preparing multi-functional polymeric materials, which are critically required for packaging industries.
- 19 September 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (1) , 544-551
Fracture Properties of SPS Tungsten Copper Powder Composites
- 19 September 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (1) , 544-551
Fracture Properties of SPS Tungsten Copper Powder Composites
- 22 January 2008
- Published by Springer Nature in International Journal of Mechanics and Materials in Design
- Vol. 4 (1) , 63-69
Mechanical and physical characterization of copper foam
- 22 January 2008
- Published by Springer Nature in International Journal of Mechanics and Materials in Design
- Vol. 4 (1) , 63-69
Mechanical and physical characterization of copper foam