Colja Schubert
Colja Schubert has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Robert Elschner
Fraunhofer Heinrich-Hertz Institute, Berlin, Germany
6 shared publications - Carsten Schmidt-Langhorst
Fraunhofer Institute for Telecommunications Heinrich-Hertz-Institute, Berlin, Germany
4 shared publications C. Schmidt-Langhorst
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institut, Berlin, Germany
3 shared publications- Isaac Sackey
Fraunhofer Institute for Telecommunications Heinrich-Hertz-Institute, Berlin, Germany
3 shared publications R. Ludwig
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institut, Berlin, Germany
3 shared publications- Tomoyuki Kato
Fujitsu Ltd., Kawasaki, Japan
3 shared publications
Latest Publications
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3695-3703
Demonstration of a 15-Mode Network Node Supported by a Field-Deployed 15-Mode Fiber
This paper extends a recent demonstration of a 2-line side 15-mode spatial division multiplexing network node. The node is based on fifteen 2×2 wavelength cross-connects (WXCs) to direct up to six 5 Tb/s, 15-mode, spatial super channels (SSCs). For this demonstration, we consider full add and drop, full express and partial add and drop network scenarios. The WXCs were made using three commercial 4×16 wavelength cross-connects, which were reprogrammed to each implement five identical 2×2 WXCs. The network node is demonstrated using a 6.1 km, 15-mode, multi-mode fiber (MMF) with a standard cladding diameter of 125 $µ$ m. This is the first field-deployed MMF and is installed in an underground tunnel in the city of L'Aquila, Italy. We further extend the network node to support up to 20 SSCs for a throughput per line side of 100 Tb/s. It is shown that the MIMO requirements for this type of systems is strongly dependent on the differential delays of the different modes propagating within the network node.
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3695-3703
Demonstration of a 15-Mode Network Node Supported by a Field-Deployed 15-Mode Fiber
This paper extends a recent demonstration of a 2-line side 15-mode spatial division multiplexing network node. The node is based on fifteen 2×2 wavelength cross-connects (WXCs) to direct up to six 5 Tb/s, 15-mode, spatial super channels (SSCs). For this demonstration, we consider full add and drop, full express and partial add and drop network scenarios. The WXCs were made using three commercial 4×16 wavelength cross-connects, which were reprogrammed to each implement five identical 2×2 WXCs. The network node is demonstrated using a 6.1 km, 15-mode, multi-mode fiber (MMF) with a standard cladding diameter of 125 $µ$ m. This is the first field-deployed MMF and is installed in an underground tunnel in the city of L'Aquila, Italy. We further extend the network node to support up to 20 SSCs for a throughput per line side of 100 Tb/s. It is shown that the MIMO requirements for this type of systems is strongly dependent on the differential delays of the different modes propagating within the network node.
- 20 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3898-3907
Optimization and Performance Evaluation of Single-Mode SOI Waveguides for Ultra-Broadband C-to-S Wavelength Conversion
In order to keep up with expected growth in data traffic, using multiple bands beyond the C band is an appealing solution as it can partly reuse deployed optical fibers. One way of handling multi-band data generation and reception is by using all-optical wavelength converters (AOWCs) to translate to or from the C band, where commercial equipment is easily available. In this work, we therefore designed and realized an AOWC targeting C-to-S band conversion. To respect the requirements of commercial applications, we aimed for a low-complexity high-bandwidth implementation with reasonably low power consumption, tolerance for typical process variations and potential for further integration. Thus we implemented the AOWC as a strip waveguide in a Silicon-on-insulator (SOI) technology. An optimization of the conversion bandwidth was conducted during design and initial characterizations confirmed a conversion efficiency of -32.8 dB and a high bandwidth of about 35 nm with grating couplers and likely beyond 50 nm for edge couplers. Using the fabricated converters, we were able to demonstrate a marginal 0.3 dB optical signal-to-noise ratio (OSNR) penalty for a back-to-back (b2b) transmission of a single-channel single-polarization 32 GBd quadrature-phase-shift keying (QPSK) signal converted from C to S band. Additionally, this converted signal was successfully transmitted over 100 km of standard single-mode fiber (SSMF). Finally, crosstalk issues arising in multi-channel conversion were investigated.
- 20 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3898-3907
Optimization and Performance Evaluation of Single-Mode SOI Waveguides for Ultra-Broadband C-to-S Wavelength Conversion
In order to keep up with expected growth in data traffic, using multiple bands beyond the C band is an appealing solution as it can partly reuse deployed optical fibers. One way of handling multi-band data generation and reception is by using all-optical wavelength converters (AOWCs) to translate to or from the C band, where commercial equipment is easily available. In this work, we therefore designed and realized an AOWC targeting C-to-S band conversion. To respect the requirements of commercial applications, we aimed for a low-complexity high-bandwidth implementation with reasonably low power consumption, tolerance for typical process variations and potential for further integration. Thus we implemented the AOWC as a strip waveguide in a Silicon-on-insulator (SOI) technology. An optimization of the conversion bandwidth was conducted during design and initial characterizations confirmed a conversion efficiency of -32.8 dB and a high bandwidth of about 35 nm with grating couplers and likely beyond 50 nm for edge couplers. Using the fabricated converters, we were able to demonstrate a marginal 0.3 dB optical signal-to-noise ratio (OSNR) penalty for a back-to-back (b2b) transmission of a single-channel single-polarization 32 GBd quadrature-phase-shift keying (QPSK) signal converted from C to S band. Additionally, this converted signal was successfully transmitted over 100 km of standard single-mode fiber (SSMF). Finally, crosstalk issues arising in multi-channel conversion were investigated.
- Open Access
Semantic Security for Indoor THz-Wireless Communication
Physical-layer security (PLS) for industrial indoor terahertz (THz) wireless communication applications is considered. We use a similar model as being employed for additive white Gaussian noise (AWGN) wireless communication channels. A cell communication and a directed communication scenario are analyzed to illustrate the achievable semantic security guarantees for a wiretap channel with finite-blocklength THz-wireless communication links. We show that weakly directed transmitter (Alice) antennas, which allow cell-type communication with multiple legitimate receivers (Bobs) without adaptation of the alignment, result in large insecure regions. In the directed communication scenario, the resulting insecure regions are shown to cover a large volume of the indoor environment only if the distance between Alice and Bob is large. Thus, our results for the two selected scenarios reveal that there is a stringent trade-off between the targeted semantic security level and the number of reliably and securely accessible legitimate receivers. Furthermore, the effects of secrecy code parameters and antenna properties on the achievable semantic security levels are illustrated to show directions for possible improvements to guarantee practically-acceptable security levels with PLS methods for industrial indoor THz-wireless communication applications.
Open AccessSemantic Security for Indoor THz-Wireless Communication
Physical-layer security (PLS) for industrial indoor terahertz (THz) wireless communication applications is considered. We use a similar model as being employed for additive white Gaussian noise (AWGN) wireless communication channels. A cell communication and a directed communication scenario are analyzed to illustrate the achievable semantic security guarantees for a wiretap channel with finite-blocklength THz-wireless communication links. We show that weakly directed transmitter (Alice) antennas, which allow cell-type communication with multiple legitimate receivers (Bobs) without adaptation of the alignment, result in large insecure regions. In the directed communication scenario, the resulting insecure regions are shown to cover a large volume of the indoor environment only if the distance between Alice and Bob is large. Thus, our results for the two selected scenarios reveal that there is a stringent trade-off between the targeted semantic security level and the number of reliably and securely accessible legitimate receivers. Furthermore, the effects of secrecy code parameters and antenna properties on the achievable semantic security levels are illustrated to show directions for possible improvements to guarantee practically-acceptable security levels with PLS methods for industrial indoor THz-wireless communication applications.
- 5 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (1) , 156-162
400-Gb/s Single-Photodiode Polarization-Agnostic Kramers–Kronig Reception of Distributedly Aggregated Superchannel
In its most simple implementation, the Kramers-Kronig (KK) scheme allows the reception of complex modulation formats with a single photodiode. Thereby, in analogy to a heterodyne receiver, an additional continuous wave signal is used that allows under certain conditions the distortion-free reconstruction of the data signal. We present experimental investigations on a novel KK scheme based on inherently polarization-aligned KK carrier generation at the receiver. We use a distributed superchannel aggregation scheme to demonstrate the ultra-wideband single-photodiode reception of a 3 × 33-GBd single-polarization 32 quadratic-amplitude modulation superchannel with this scheme. The impact of polarization rotations is discussed, and we show that variations in data or KK carrier polarization will only affect the carrier-to-signal power ratio (CSPR), leading to an increase or decrease from the optimum CSPR by about 6 dB. A net capacity of 400 Gb/s is demonstrated for optimized conditions. In addition, we demonstrate transmission measurements over a 60-km standard single-mode fiber link with a 344-Gb/s net rate superchannel (3 × 28 GBd sub-carriers) with the novel KK scheme.
- 5 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (1) , 156-162
400-Gb/s Single-Photodiode Polarization-Agnostic Kramers–Kronig Reception of Distributedly Aggregated Superchannel
In its most simple implementation, the Kramers-Kronig (KK) scheme allows the reception of complex modulation formats with a single photodiode. Thereby, in analogy to a heterodyne receiver, an additional continuous wave signal is used that allows under certain conditions the distortion-free reconstruction of the data signal. We present experimental investigations on a novel KK scheme based on inherently polarization-aligned KK carrier generation at the receiver. We use a distributed superchannel aggregation scheme to demonstrate the ultra-wideband single-photodiode reception of a 3 × 33-GBd single-polarization 32 quadratic-amplitude modulation superchannel with this scheme. The impact of polarization rotations is discussed, and we show that variations in data or KK carrier polarization will only affect the carrier-to-signal power ratio (CSPR), leading to an increase or decrease from the optimum CSPR by about 6 dB. A net capacity of 400 Gb/s is demonstrated for optimized conditions. In addition, we demonstrate transmission measurements over a 60-km standard single-mode fiber link with a 344-Gb/s net rate superchannel (3 × 28 GBd sub-carriers) with the novel KK scheme.
- Open Access
Terahertz Technologies to Deliver Optical Network Quality of Experience in Wireless Systems Beyond 5G
This article discusses the basic system architecture for terahertz (THz) wireless links with bandwidths of more than 50 GHz into optical networks. New design principles and breakthrough technologies are required in order to demonstrate Tbps data-rates at near zero-latency using the proposed system concept. Specifically, we present the concept of designing the baseband signal processing for both the optical and wireless link and using an end-to-end (E2E) error correction approach for the combined link. We provide two possible electro-optical baseband interface architectures, namely transparent optical-link and digital-link architectures, which are currently under investigation. THz wireless link requirements are given as well as the main principles and research directions for the development of a new generation of transceiver frontends, which will be capable of operating at ultra-high spectral efficiency by employing higher-order modulation schemes. Moreover, we discuss the need for developing a novel THz network information theory framework, which will take into account the channel characteristics and the nature of interference in the THz band. Finally, we highlight the role of pencil-beamforming (PBF), which is required in order to overcome the propagation losses, as well as the physical layer and medium access control challenges.
Open AccessTerahertz Technologies to Deliver Optical Network Quality of Experience in Wireless Systems Beyond 5G
This article discusses the basic system architecture for terahertz (THz) wireless links with bandwidths of more than 50 GHz into optical networks. New design principles and breakthrough technologies are required in order to demonstrate Tbps data-rates at near zero-latency using the proposed system concept. Specifically, we present the concept of designing the baseband signal processing for both the optical and wireless link and using an end-to-end (E2E) error correction approach for the combined link. We provide two possible electro-optical baseband interface architectures, namely transparent optical-link and digital-link architectures, which are currently under investigation. THz wireless link requirements are given as well as the main principles and research directions for the development of a new generation of transceiver frontends, which will be capable of operating at ultra-high spectral efficiency by employing higher-order modulation schemes. Moreover, we discuss the need for developing a novel THz network information theory framework, which will take into account the channel characteristics and the nature of interference in the THz band. Finally, we highlight the role of pencil-beamforming (PBF), which is required in order to overcome the propagation losses, as well as the physical layer and medium access control challenges.
- 8 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (6) , 1309-1317
Waveband-Shift-Free Optical Phase Conjugator for Spectrally Efficient Fiber Nonlinearity Mitigation
We discuss a novel broadband, polarization-insensitive and wavelength-shift free optical phase conjugator (OPC). In the OPC scheme, the original input signal is inherently suppressed in a polarization-diversity loop setup. This allows for spectrally efficient, wavelength-(band)-shift free generation of phase conjugated idlers over a continuous operating band. The idlers are generated using four-wave mixing in nonlinear fibers using out-of-band, orthogonally polarized pump waves. The saturation characteristics of the exploited nonlinear mixing process as well as the crosstalk characteristics of the OPC diversity loop scheme are investigated. The OPC subsystem is finally utilized for fiber nonlinearity mitigation by mid-link spectral inversion (MLSI) in 800 km transmission experiments over dispersion-managed fiber spans with lumped amplification by Erbium doped fiber amplifiers (EDFA). Q2-factor improvements of up to 0.7 dB are obtained in transmission of a 300-GHz wide 1.6 Tb/s superchannel consisting of eight 200 Gb/s polarization division multiplexed 16-ary quadrature amplitude modulation (PDM-16QAM) sub-channels.
- 8 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (6) , 1309-1317
Waveband-Shift-Free Optical Phase Conjugator for Spectrally Efficient Fiber Nonlinearity Mitigation
We discuss a novel broadband, polarization-insensitive and wavelength-shift free optical phase conjugator (OPC). In the OPC scheme, the original input signal is inherently suppressed in a polarization-diversity loop setup. This allows for spectrally efficient, wavelength-(band)-shift free generation of phase conjugated idlers over a continuous operating band. The idlers are generated using four-wave mixing in nonlinear fibers using out-of-band, orthogonally polarized pump waves. The saturation characteristics of the exploited nonlinear mixing process as well as the crosstalk characteristics of the OPC diversity loop scheme are investigated. The OPC subsystem is finally utilized for fiber nonlinearity mitigation by mid-link spectral inversion (MLSI) in 800 km transmission experiments over dispersion-managed fiber spans with lumped amplification by Erbium doped fiber amplifiers (EDFA). Q2-factor improvements of up to 0.7 dB are obtained in transmission of a 300-GHz wide 1.6 Tb/s superchannel consisting of eight 200 Gb/s polarization division multiplexed 16-ary quadrature amplitude modulation (PDM-16QAM) sub-channels.
- 15 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 23 (22) , 1649-1651
Phase-Incoherent DQPSK Wavelength Conversion Using a Photonic Integrated Circuit
We investigate the performance of a large-scale, silica-on-silicon photonic integrated circuit for multiformat signal processing, and we experimentally demonstrate wavelength-conversion of (differential) quadrature phase-shift keying [(D)QPSK] signals. The circuit exploits phase-incoherent techniques to decode the input signal and to phase remodulate two phase-shift-keying components before combining them in a common QPSK output stream. Error-free wavelength conversion with 4-dB power penalty is reported at 44 Gb/s.
- 15 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 23 (22) , 1649-1651
Phase-Incoherent DQPSK Wavelength Conversion Using a Photonic Integrated Circuit
We investigate the performance of a large-scale, silica-on-silicon photonic integrated circuit for multiformat signal processing, and we experimentally demonstrate wavelength-conversion of (differential) quadrature phase-shift keying [(D)QPSK] signals. The circuit exploits phase-incoherent techniques to decode the input signal and to phase remodulate two phase-shift-keying components before combining them in a common QPSK output stream. Error-free wavelength conversion with 4-dB power penalty is reported at 44 Gb/s.
- 4 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 18 (2) , 988-995
Parametric Amplification and Wavelength Conversion of Single- and Dual-Polarization DQPSK Signals
We demonstrate system experiments for polarization-independent parametric amplification and wavelength conversion of single-channel differential quadrature phase-shift keying (DQPSK) signals up to 112 Gbit/s. Dual-pump four-wave mixing in a highly nonlinear fiber is utilized to achieve up to 20 dB ON-OFF gain and conversion efficiency. The investigations are done in a polarization-dependent (straight) as well as in a polarization-independent (loop) configuration using single- and dual-polarization DQPSK. Particular attention is paid to the resulting optical signal-to-noise ratio penalties after the amplification. We ascribe this to pump-induced nonlinear phase noise. It is shown that this type of excess noise is increased for the loop configuration in comparison with the straight configuration due to Rayleigh backscattering and that it depends on the input polarization of the signal. Still, the penalty can be made negligible using high-quality pump sources.
- 4 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 18 (2) , 988-995
Parametric Amplification and Wavelength Conversion of Single- and Dual-Polarization DQPSK Signals
We demonstrate system experiments for polarization-independent parametric amplification and wavelength conversion of single-channel differential quadrature phase-shift keying (DQPSK) signals up to 112 Gbit/s. Dual-pump four-wave mixing in a highly nonlinear fiber is utilized to achieve up to 20 dB ON-OFF gain and conversion efficiency. The investigations are done in a polarization-dependent (straight) as well as in a polarization-independent (loop) configuration using single- and dual-polarization DQPSK. Particular attention is paid to the resulting optical signal-to-noise ratio penalties after the amplification. We ascribe this to pump-induced nonlinear phase noise. It is shown that this type of excess noise is increased for the loop configuration in comparison with the straight configuration due to Rayleigh backscattering and that it depends on the input polarization of the signal. Still, the penalty can be made negligible using high-quality pump sources.
- 2 July 2010
- Published by Springer Nature in Applied Physics B
- Vol. 101 (4) , 875-882
Polarization-insensitive all-optical wavelength conversion of 320 Gb/s RZ-DQPSK signals using a Ti:PPLN waveguide
- 2 July 2010
- Published by Springer Nature in Applied Physics B
- Vol. 101 (4) , 875-882
Polarization-insensitive all-optical wavelength conversion of 320 Gb/s RZ-DQPSK signals using a Ti:PPLN waveguide
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 913-914
Single Channel Transmission Beyond 1 Tbit/s
We report on components and techniques for single wavelength channel transmission of 1.28 Tbit/s over 240 km and 2.56 Tbit/s over 160 km. The enabling technologies were the OTDM technology, the DQPSK modulation format, precise dispersion management of the fiber link and polarization multiplexing
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 913-914
Single Channel Transmission Beyond 1 Tbit/s
We report on components and techniques for single wavelength channel transmission of 1.28 Tbit/s over 240 km and 2.56 Tbit/s over 160 km. The enabling technologies were the OTDM technology, the DQPSK modulation format, precise dispersion management of the fiber link and polarization multiplexing