Erhard Kaschnitz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Erhard Kaschnitz has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Alejandro Lazaro Martinez
AIMEN Technology Centre
1 shared publication - Andreas Cziegler
Österreichisches Gießerei-Institut, Leoben, Austria
1 shared publication - Camilo Prieto Rio
AIMEN Technology Centre
1 shared publication - Clovis Alleaume
AIMEN Technology Centre
1 shared publication - Gemma Castro Regal
AIMEN Technology Centre
1 shared publication L. Kaschnitz
Österreichisches Gießerei-Institut
1 shared publication
Latest Publications
- 9 November 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (5) , 1-9
Training of Artificial Neural Networks with Result Data from Numerous Casting Simulation Variants
- 9 November 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (5) , 1-9
Training of Artificial Neural Networks with Result Data from Numerous Casting Simulation Variants
- Open Access
- 23 November 2023
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 964, 157-162
Laser-Based Directed Energy Deposition of Ceramic Nanoadditivated AA7075 Powder Alloys
AA7075 is one of the most resistant aluminium alloys, so it is frequently used in very demanding industries as aeronautics or defence. However, the 7075 alloy falls into the non-weldable category thus hardly processable through additive manufacturing processes, and specially on laser-based DED (Directed Energy Deposition). The low absorption together with cracking behaviour remain a challenge for the industrialisation of these processes. Alloying with minor elements or addition of nano-reinforcement have been proven as a successful approach to increase its manufacturability. In this work, the feasibility of printing 7075 with nano-TiC as additive was evaluated. Two compositions with 0.5 and 2% in weight were developed by dry mixing. The powders were characterized by scanning electron microscopy (SEM) and flowability was compared with the unreinforced alloy. With the optimal laser process parameters, 3D coupons were printed to be characterized microstructurally, thermally, and mechanically. Process monitoring using thermal and high-speed cameras was carried out to gain insight into the thermal behaviour of the melt-pool and resulting process stability. After printing, aspect ratio of single tracks was measured, and dilution was also evaluated. Although addition of 0.5% of n-TiC promotes a slight improvement on the alloy, allowing it to be mechanically tested, it still presents some defects as porosity. By increasing the content up to 2%, both the quality and the mechanical performance were enhanced significantly.
- 23 November 2023
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 964, 157-162
Open AccessLaser-Based Directed Energy Deposition of Ceramic Nanoadditivated AA7075 Powder Alloys
AA7075 is one of the most resistant aluminium alloys, so it is frequently used in very demanding industries as aeronautics or defence. However, the 7075 alloy falls into the non-weldable category thus hardly processable through additive manufacturing processes, and specially on laser-based DED (Directed Energy Deposition). The low absorption together with cracking behaviour remain a challenge for the industrialisation of these processes. Alloying with minor elements or addition of nano-reinforcement have been proven as a successful approach to increase its manufacturability. In this work, the feasibility of printing 7075 with nano-TiC as additive was evaluated. Two compositions with 0.5 and 2% in weight were developed by dry mixing. The powders were characterized by scanning electron microscopy (SEM) and flowability was compared with the unreinforced alloy. With the optimal laser process parameters, 3D coupons were printed to be characterized microstructurally, thermally, and mechanically. Process monitoring using thermal and high-speed cameras was carried out to gain insight into the thermal behaviour of the melt-pool and resulting process stability. After printing, aspect ratio of single tracks was measured, and dilution was also evaluated. Although addition of 0.5% of n-TiC promotes a slight improvement on the alloy, allowing it to be mechanically tested, it still presents some defects as porosity. By increasing the content up to 2%, both the quality and the mechanical performance were enhanced significantly.
- 1 January 2020
- Published by Old City Publishing, Inc in High Temperatures-High Pressures
- Vol. 49 (1-2) , 75-87
Electrical resistivity measured by millisecond pulse-heating in comparison to thermal conductivity of the hot work tool steel AISI H11 (1.2343) at elevated temperature
HTHP Home • Issue Contents • Forthcoming Papers Electrical resistivity measured by millisecond pulse-heating in comparison to thermal conductivity of the hot work tool steel AISI H11 (1.2343) at el…
- 1 January 2020
- Published by Old City Publishing, Inc in High Temperatures-High Pressures
- Vol. 49 (1-2) , 75-87
Electrical resistivity measured by millisecond pulse-heating in comparison to thermal conductivity of the hot work tool steel AISI H11 (1.2343) at elevated temperature
HTHP Home • Issue Contents • Forthcoming Papers Electrical resistivity measured by millisecond pulse-heating in comparison to thermal conductivity of the hot work tool steel AISI H11 (1.2343) at el…
- 5 February 2012
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 34 (5) , 843-850
Thermophysical Properties of a Hot-Work Tool-Steel with High Thermal Conductivity
- 5 February 2012
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 34 (5) , 843-850
Thermophysical Properties of a Hot-Work Tool-Steel with High Thermal Conductivity