H. P. Evans
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
H. P. Evans has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- R. W. Snidle
School of Engineering, Cardiff University, Cardiff, UK
4 shared publications - K. J. Sharif
Cardiff University, Cardiff, UK
2 shared publications D W Parkins
1 shared publication- Hazim U. Jamali
Mechanical Engineering Department, College of Engineering, University of Kerbala, Karbala 56001, Iraq
1 shared publication J. P. Newall
Torotrak Development, Ltd., Leyland, UK
1 shared publicationL M Rudd
1 shared publication
Latest Publications
- 9 October 2014
- Published by Taylor & Francis in Tribology Transactions
- Vol. 58 (1) , 119-130
The Transient Effects of Profile Modification on Elastohydrodynamic Oil Films in Helical Gears
This article presents the results of a transient elastohydrodynamic analysis of the conditions at the contact of two pairs of helical gears operating with different gear ratios. The effects of the variation in contact geometry, kinematics, and tooth loading during the meshing cycle are taken into account together with both tip relief and axial crowning profile modifications. The results are compared with analyses under corresponding steady-state conditions for both point contact and equivalent line contact models. The comparisons show that, away from the ends of the contact lines, steady-state conditions can be used effectively to assess the film-forming capabilities of the gears. Conditions at the end of the contact lines are found to be more adverse with significant transient squeeze film effects. The form of tip relief profile adopted is shown to be highly influential in determining the peak contact pressures and thinnest oil films within the contacts. These conditions are experienced at all axial positions on the tooth flanks at the locations of the start of tip relief profile modifications. If the tip relief profile introduces a slope discontinuity to the gear profile, this can cause a significant stress concentration and very poor film-forming behavior.
- 9 October 2014
- Published by Taylor & Francis in Tribology Transactions
- Vol. 58 (1) , 119-130
The Transient Effects of Profile Modification on Elastohydrodynamic Oil Films in Helical Gears
This article presents the results of a transient elastohydrodynamic analysis of the conditions at the contact of two pairs of helical gears operating with different gear ratios. The effects of the variation in contact geometry, kinematics, and tooth loading during the meshing cycle are taken into account together with both tip relief and axial crowning profile modifications. The results are compared with analyses under corresponding steady-state conditions for both point contact and equivalent line contact models. The comparisons show that, away from the ends of the contact lines, steady-state conditions can be used effectively to assess the film-forming capabilities of the gears. Conditions at the end of the contact lines are found to be more adverse with significant transient squeeze film effects. The form of tip relief profile adopted is shown to be highly influential in determining the peak contact pressures and thinnest oil films within the contacts. These conditions are experienced at all axial positions on the tooth flanks at the locations of the start of tip relief profile modifications. If the tip relief profile introduces a slope discontinuity to the gear profile, this can cause a significant stress concentration and very poor film-forming behavior.
- 1 January 2013
- Published by Springer Nature
- p. 751-758
Differential Deflection Method for Deformation
- 1 January 2003
- Published by ASME International
- Vol. 2003, 903-911
Analysis of Microelastohydrodynamic and Mixed Lubrication Effects in Gear Tooth Contacts
The paper presents results obtained using a transient analysis technique for point contact elastohydrodynamic lubrication (EHL) problems based on a formulation that couples the elastic and hydrodynamic equations. Results are presented for transverse ground surfaces in elliptical point contact that show severe film thinning at the transverse limits of the contact area. This thinning is caused by transverse leakage of the lubricant from the contact in the remaining deep valley features. A comparison is also made between the point contact results on the entrainment centre line and the equivalent line contact analysis.
- 1 January 2003
- Published by ASME International
- Vol. 2003, 903-911
Analysis of Microelastohydrodynamic and Mixed Lubrication Effects in Gear Tooth Contacts
The paper presents results obtained using a transient analysis technique for point contact elastohydrodynamic lubrication (EHL) problems based on a formulation that couples the elastic and hydrodynamic equations. Results are presented for transverse ground surfaces in elliptical point contact that show severe film thinning at the transverse limits of the contact area. This thinning is caused by transverse leakage of the lubricant from the contact in the remaining deep valley features. A comparison is also made between the point contact results on the entrainment centre line and the equivalent line contact analysis.
- 1 January 2003
- Published by ASME International
- p. 805-815
Modelling of Film Thickness and Traction in a Variable Ratio Traction Drive Rig
The paper describes the application of a full non-Newtonian, thermal elastohydrodynamic lubrication (EHL) model for the prediction of film thickness and viscous traction force in a special high speed rolling traction rig. The primary objective of the work was to identify a suitable lubricant rheological model that would describe the behavior of practical EHL traction drive contacts over their operating range. Experiments were carried out on a special rolling contact rig at temperatures of 60, 90 and 120°C and contact loads giving maximum Hertzian pressures of 1, 2 and 3 GPa. Entrainment speeds of up to 18 m/s were investigated. Corresponding modelling work was carried out using lubricant physical properties obtained for the traction fluid Santotrac 50. Viscosity data for this lubricant were available from the work of Bair and Winer, but a degree of extrapolation was required to this data to cover the range of the experiments. In view of the crucial importance of viscosity/pressure behavior in the prediction of traction attention was therefore focused upon the lower contact loads for which reliable viscosity/pressure data are available. A best-fit exercise was then carried out to establish an appropriate rheological model to account for shear thinning of the lubricant. Different non-Newtonian relationships were investigated including those of Johnson and Tevaarwerk, Bair and Winer, and a model which combined the features of both of these. The most encouraging agreement between experiment and theory over the range of temperatures and speeds considered was obtained with the Johnson and Tevaarwerk (Eyring) model.
- 1 January 2003
- Published by ASME International
- p. 805-815
Modelling of Film Thickness and Traction in a Variable Ratio Traction Drive Rig
The paper describes the application of a full non-Newtonian, thermal elastohydrodynamic lubrication (EHL) model for the prediction of film thickness and viscous traction force in a special high speed rolling traction rig. The primary objective of the work was to identify a suitable lubricant rheological model that would describe the behavior of practical EHL traction drive contacts over their operating range. Experiments were carried out on a special rolling contact rig at temperatures of 60, 90 and 120°C and contact loads giving maximum Hertzian pressures of 1, 2 and 3 GPa. Entrainment speeds of up to 18 m/s were investigated. Corresponding modelling work was carried out using lubricant physical properties obtained for the traction fluid Santotrac 50. Viscosity data for this lubricant were available from the work of Bair and Winer, but a degree of extrapolation was required to this data to cover the range of the experiments. In view of the crucial importance of viscosity/pressure behavior in the prediction of traction attention was therefore focused upon the lower contact loads for which reliable viscosity/pressure data are available. A best-fit exercise was then carried out to establish an appropriate rheological model to account for shear thinning of the lubricant. Different non-Newtonian relationships were investigated including those of Johnson and Tevaarwerk, Bair and Winer, and a model which combined the features of both of these. The most encouraging agreement between experiment and theory over the range of temperatures and speeds considered was obtained with the Johnson and Tevaarwerk (Eyring) model.
- 1 January 1997
- Published by Elsevier in Tribology Series
- p. 287-296
Lubrication of thrust cone bearings
- 1 January 1997
- Published by Elsevier in Tribology Series
- p. 287-296
Lubrication of thrust cone bearings