Azlan Ariffin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Azlan Ariffin has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
S. S. Jikan
Universiti Sains Malaysia
4 shared publications- Zulkifli Mohamad Ariff
Universiti Sains Malaysia image/svg+xml
4 shared publications A. S. Mansor
School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, Penang, Malaysia
1 shared publicationAs Mansor
School of Materials and Mineral Resources Engineering, Engineering Campus, University Sains Malaysia, Malaysia
1 shared publication- Azura Abdul Rashid
School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, Nibong Tebal, Malaysia
1 shared publication Hanafi Ismail
School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, Nibong Tebal, Penang, Malaysia
1 shared publication
Latest Publications
- 14 November 2012
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 45 (6) , 523-535
Comparison of mechanical, morphological and swelling properties of WNRL/PS and NRv/PS blends
Natural rubber latex waste was dried in an ambient temperature and was milled by a two-roll mill prior to blending with polystyrene (PS) for the purpose of recycling. These blends were prepared at different milled waste natural rubber latex (WNRL) and PS ratios, and the effect of PS content on the mechanical properties was investigated. As the PS content increased, the tensile strength and the Young’s modulus also increased, but the elongation at break decreased. The blend morphologies were observed using transmission electron microscope. A dynamically vulcanized natural rubber/PS blend and a natural rubber (NR)/PS blend were prepared and compared with WNRL/PS blend. WNRL/PS blend showed higher tensile strength and Young’s modulus compared with other blends.
- 14 November 2012
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 45 (6) , 523-535
Comparison of mechanical, morphological and swelling properties of WNRL/PS and NRv/PS blends
Natural rubber latex waste was dried in an ambient temperature and was milled by a two-roll mill prior to blending with polystyrene (PS) for the purpose of recycling. These blends were prepared at different milled waste natural rubber latex (WNRL) and PS ratios, and the effect of PS content on the mechanical properties was investigated. As the PS content increased, the tensile strength and the Young’s modulus also increased, but the elongation at break decreased. The blend morphologies were observed using transmission electron microscope. A dynamically vulcanized natural rubber/PS blend and a natural rubber (NR)/PS blend were prepared and compared with WNRL/PS blend. WNRL/PS blend showed higher tensile strength and Young’s modulus compared with other blends.
- 31 August 2012
- Published by Wiley in Starch - Stärke
- Vol. 64 (12) , 935-943
Application of response surface methodology (RSM) for optimization of cassava starch grafted polyDADMAC synthesis for cationic properties
Response surface methodology was used to study the process optimization of cationic percentage through grafting diallyldimethylammonium chloride (DADMAC) into cassava starch. Based on Box–Behken design, quadratic models were developed to correlate the synthesis variables: concentration of DADMAC (A), concentration of initiator (B), and polymerization temperature (C), to the responses of cationic percentage (y). Analysis of variance (ANOVA) revealed that the concentration of initiator was the most significant variable for the response. The optimum preparation conditions for starch grafted polyDADMAC were 14% cationic using 31 g DADMAC/10 g dry starch of concentration DADMAC, a polymerization temperature of 74°C, and 4.92 g cerric ammonium nitrate/10 mL of initiator concentration.
- 31 August 2012
- Published by Wiley in Starch - Stärke
- Vol. 64 (12) , 935-943
Application of response surface methodology (RSM) for optimization of cassava starch grafted polyDADMAC synthesis for cationic properties
Response surface methodology was used to study the process optimization of cationic percentage through grafting diallyldimethylammonium chloride (DADMAC) into cassava starch. Based on Box–Behken design, quadratic models were developed to correlate the synthesis variables: concentration of DADMAC (A), concentration of initiator (B), and polymerization temperature (C), to the responses of cationic percentage (y). Analysis of variance (ANOVA) revealed that the concentration of initiator was the most significant variable for the response. The optimum preparation conditions for starch grafted polyDADMAC were 14% cationic using 31 g DADMAC/10 g dry starch of concentration DADMAC, a polymerization temperature of 74°C, and 4.92 g cerric ammonium nitrate/10 mL of initiator concentration.
- 17 February 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (4) , 395-403
Review: Single Screw Extruder in Particulate Filler Composite
This review is designed to be a comprehensive source for single screw extruder research in the scope of particulate filled composite. This review includes factors effecting processing of particulate filled composite using a single screw extruder. The mixing requirements for a particulate filled composite analyzed and discussed in terms of single screw extrusion. The factors for achieving effective mixing of this type of composite are also discussed.
- 17 February 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (4) , 395-403
Review: Single Screw Extruder in Particulate Filler Composite
This review is designed to be a comprehensive source for single screw extruder research in the scope of particulate filled composite. This review includes factors effecting processing of particulate filled composite using a single screw extruder. The mixing requirements for a particulate filled composite analyzed and discussed in terms of single screw extrusion. The factors for achieving effective mixing of this type of composite are also discussed.
- Open Access
- 1 December 2010
- Published by Walter de Gruyter GmbH in e-Polymers
- Vol. 10 (1) , 1069-1082
Effects of kaolin and maleic anhydride contents on melt elasticity and flexural behaviour of polypropylene/kaolin and unplasticised poly(vinyl chloride)/kaolin composites
Polypropylene/kaolin and unplasticised poly(vinyl chloride)/kaolin composites were prepared by directly melt mixing polypropylene (PP) and unplasticised poly(vinyl chloride) (UPVC) with maleic anhydride (MAH) and low cost kaolin via in situ extrusion process. The influences of kaolin particles and MAH in PP and UPVC matrix were discussed through investigating the flexural and morphological properties of filled PP and UPVC composites. The extrudates obtained from the extrusion process were carefully collected in order to investigate the elastic properties (extrudate swell and melt fracture). Results revealed that the above mentioned properties are strongly dependent on the presences of kaolin and MAH in both composite systems. Observation on scanning electron microscopy (SEM) analysis showed that the kaolin books (stacks of kaolin particles) were successfully delaminated thus lead to a well dispersed of kaolin particles in PP and UPVC matrix.
- 1 December 2010
- Published by Walter de Gruyter GmbH in e-Polymers
- Vol. 10 (1) , 1069-1082
Open AccessEffects of kaolin and maleic anhydride contents on melt elasticity and flexural behaviour of polypropylene/kaolin and unplasticised poly(vinyl chloride)/kaolin composites
Polypropylene/kaolin and unplasticised poly(vinyl chloride)/kaolin composites were prepared by directly melt mixing polypropylene (PP) and unplasticised poly(vinyl chloride) (UPVC) with maleic anhydride (MAH) and low cost kaolin via in situ extrusion process. The influences of kaolin particles and MAH in PP and UPVC matrix were discussed through investigating the flexural and morphological properties of filled PP and UPVC composites. The extrudates obtained from the extrusion process were carefully collected in order to investigate the elastic properties (extrudate swell and melt fracture). Results revealed that the above mentioned properties are strongly dependent on the presences of kaolin and MAH in both composite systems. Observation on scanning electron microscopy (SEM) analysis showed that the kaolin books (stacks of kaolin particles) were successfully delaminated thus lead to a well dispersed of kaolin particles in PP and UPVC matrix.
- 14 October 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (23) , 3429-3441
Evaluation of hybridizing talc and surface-treated kaolin on the properties of PP hybrid composites
In this article, the effects of kaolin surface treatment on mechanical, morphological, and thermal behavior of PP/talc/ kaolin hybrid composites with different filler ratio were studied. Kaolin was pre-treated with QAC and SHMP, in order to eradicate the attraction of kaolin interparticle forces. It was found that both types of treatments enhanced the toughness of the composite remarkably. Although the tensile and flexural strength of the treated composites reduced with increasing amount of kaolin, it was still acceptably higher than the untreated composite. The enhancement of flexural modulus of the treated composites was attributed to the improvement of filler dispersion as observed by SEM results. In the light of the results achieved, the QAC proved to be more effective as dispersant for kaolin filler. This finding was further confirmed by thermal analysis and MFI study which shows that the properties of QAC-treated kaolin composites were comparable to the properties of talc-filled PP composite.
- 14 October 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (23) , 3429-3441
Evaluation of hybridizing talc and surface-treated kaolin on the properties of PP hybrid composites
In this article, the effects of kaolin surface treatment on mechanical, morphological, and thermal behavior of PP/talc/ kaolin hybrid composites with different filler ratio were studied. Kaolin was pre-treated with QAC and SHMP, in order to eradicate the attraction of kaolin interparticle forces. It was found that both types of treatments enhanced the toughness of the composite remarkably. Although the tensile and flexural strength of the treated composites reduced with increasing amount of kaolin, it was still acceptably higher than the untreated composite. The enhancement of flexural modulus of the treated composites was attributed to the improvement of filler dispersion as observed by SEM results. In the light of the results achieved, the QAC proved to be more effective as dispersant for kaolin filler. This finding was further confirmed by thermal analysis and MFI study which shows that the properties of QAC-treated kaolin composites were comparable to the properties of talc-filled PP composite.
- 16 September 2010
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 103 (1) , 171-177
Evaluation on nonisothermal crystallization kinetics of polypropylene/kaolin composites by employing Dobreva and Kissinger methods
- 16 September 2010
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 103 (1) , 171-177
Evaluation on nonisothermal crystallization kinetics of polypropylene/kaolin composites by employing Dobreva and Kissinger methods
- 2 July 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (23) , 3442-3449
Contact angle of untreated/treated kaolin and its correlation with the mechanical properties of PP-kaolin composites
This research relates the effect of contact angle and surface free energy on the mechanical properties of chemically treated and untreated kaolin filler polypropylene (PP) composites. The contact angle of untreated as well as treated kaolin filler samples was obtained using thin layer wicking technique and Washburn’s equation. The information recorded is incorporated into the Young’s equation to obtain the value of surface free energy. The interfacial adhesion of the composite was quantitatively analyzed by using the Pukanszky model. Treated and untreated kaolin filler samples were compounded with PP in a Brabender Plasticorder to produce a PP—kaolin composite. The compound consists of various filler contents ranging 0%, 5%, 10%, and 15%. Tensile, flexural, and impact tests show that treated samples have stronger mechanical properties than untreated PP—kaolin composite. The thin layer wicking technique shows that for treated kaolin samples, a high contact angle is obtained. The surface energy obtained was also low for treated kaolin samples. A conclusion could be made here that high contact angle will have lower surface energy which will then lead to an increase in compatibility of kaolin filler in the composite. Increase in compatibility will increase the mechanical property, which is portrayed by treated PP—kaolin composite samples.
- 2 July 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (23) , 3442-3449
Contact angle of untreated/treated kaolin and its correlation with the mechanical properties of PP-kaolin composites
This research relates the effect of contact angle and surface free energy on the mechanical properties of chemically treated and untreated kaolin filler polypropylene (PP) composites. The contact angle of untreated as well as treated kaolin filler samples was obtained using thin layer wicking technique and Washburn’s equation. The information recorded is incorporated into the Young’s equation to obtain the value of surface free energy. The interfacial adhesion of the composite was quantitatively analyzed by using the Pukanszky model. Treated and untreated kaolin filler samples were compounded with PP in a Brabender Plasticorder to produce a PP—kaolin composite. The compound consists of various filler contents ranging 0%, 5%, 10%, and 15%. Tensile, flexural, and impact tests show that treated samples have stronger mechanical properties than untreated PP—kaolin composite. The thin layer wicking technique shows that for treated kaolin samples, a high contact angle is obtained. The surface energy obtained was also low for treated kaolin samples. A conclusion could be made here that high contact angle will have lower surface energy which will then lead to an increase in compatibility of kaolin filler in the composite. Increase in compatibility will increase the mechanical property, which is portrayed by treated PP—kaolin composite samples.
- 6 May 2010
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 102 (3) , 1011-1017
Influence of filler content and processing parameter on the crystallization behaviour of PP/kaolin composites
- 6 May 2010
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 102 (3) , 1011-1017
Influence of filler content and processing parameter on the crystallization behaviour of PP/kaolin composites
- 17 March 2008
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (6) , 3901-3916
Mechanical, morphological, and thermal properties of polypropylene/kaolin composite. Part I. The effects of surface‐treated kaolin and processing enhancement
- 17 March 2008
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (6) , 3901-3916
Mechanical, morphological, and thermal properties of polypropylene/kaolin composite. Part I. The effects of surface‐treated kaolin and processing enhancement
- 28 September 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (6) , 5421-5426
Effect of filler treatments on rheological behavior of calcium carbonate and talc‐filled polypropylene hybrid composites
Commercial stearic acid treated calcium carbonate (CaCO3) was used to make a comparative study on rheological behavior of the CaCO3 and talc‐filled polypropylene (PP) hybrid composites with nontreated filler. Apparent shear viscosity and extrudate swell were investigated with variation of filler ratio and temperature with 30% by weight total of filler was used in PP composite. The Shimadzu capillary rheometer was used to evaluate shear viscosity and shear rate of the composite. It was found that the shear viscosities decrease with increasing shear rate. The apparent shear viscosity of the composite containing the stearic acid treated is slightly lower than untreated filler. Shear thickening behavior at higher shear rate has also shown by 15/15 treated composites at higher temperature about 220°C and investigation by SEM has proved that filler being densely packed at that condition. Treated composites also exhibit lower swelling ratio value than untreated composite, and swelling ratio also decreases linearly with increasing temperature and the die length–diameter ratio. It is believed that dispersion of filler play an important role not only on shear viscosity but also on swelling ratio of PP composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5421–5426, 2006
- 28 September 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (6) , 5421-5426
Effect of filler treatments on rheological behavior of calcium carbonate and talc‐filled polypropylene hybrid composites
Commercial stearic acid treated calcium carbonate (CaCO3) was used to make a comparative study on rheological behavior of the CaCO3 and talc‐filled polypropylene (PP) hybrid composites with nontreated filler. Apparent shear viscosity and extrudate swell were investigated with variation of filler ratio and temperature with 30% by weight total of filler was used in PP composite. The Shimadzu capillary rheometer was used to evaluate shear viscosity and shear rate of the composite. It was found that the shear viscosities decrease with increasing shear rate. The apparent shear viscosity of the composite containing the stearic acid treated is slightly lower than untreated filler. Shear thickening behavior at higher shear rate has also shown by 15/15 treated composites at higher temperature about 220°C and investigation by SEM has proved that filler being densely packed at that condition. Treated composites also exhibit lower swelling ratio value than untreated composite, and swelling ratio also decreases linearly with increasing temperature and the die length–diameter ratio. It is believed that dispersion of filler play an important role not only on shear viscosity but also on swelling ratio of PP composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5421–5426, 2006