Mihaela Cretu
Mihaela Cretu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
A. Răcășan
Technical University of Cluj-Napoca/Electrotechnics and Measurements Department
1 shared publicationAdrian Darabant
Computer Science Department, Babeş-Bolyai University, Cluj-Napoca, Romania
1 shared publication- Dan Doru Micu
Technical University of Cluj-Napoca, Cluj-Napoca, Romania
1 shared publication - Gyorgy Thalmaier
Faculty of Materials and Environmental Engineering, Technical University of Cluj-Napoca, 103–105 Muncii Boulevard, 400641 Cluj-Napoca, Romania
1 shared publication L. Darabant
Technical University of Cluj-Napoca/Electrotechnics and Measurements Department
1 shared publicationLaura Darabant
1 shared publication
Latest Publications
- Open Access
Properties of n-Octadecane PCM Composite with Recycled Aluminum as a Thermal Enhancer
This paper presents new types of PCM composites proposed and analyzed for cooling applications in buildings. The composites (n-octadecane-Al-long/n-octadecane-Al-short) were made of n-octadecane with 7% and 7.5% vol. of recycled aluminum added as a thermal conductivity enhancer to avoid sinking during the melting phase and to improve thermal conductivity. Recycled aluminum chips are inexpensive, abundant, and generate a lower environmental impact during composite production. The effect of the chip content was found to increase the thermal conductivity values of the composites by 100% (n-octadecane-Al short) and by 600% (n-octadecane-Al-long) compared to n-octadecane. The percentage of mass increase remained low. The latent heat of n-octadecane-Al-long decreased from 245 kJ/kg to 195 kJ/kg, the melting time shortened from 990 s to 850 s, and the CO2 emission reduction was by 150 kg CO2eq/year. The volume of the PCM composites varied from 0.083 m3 (n-octadecane) to 0.091 for n-octadecane-Al-long, which represents an increase of up to 11% needed to absorb the solar heat gained by the optimized PCM composite.
Open AccessProperties of n-Octadecane PCM Composite with Recycled Aluminum as a Thermal Enhancer
This paper presents new types of PCM composites proposed and analyzed for cooling applications in buildings. The composites (n-octadecane-Al-long/n-octadecane-Al-short) were made of n-octadecane with 7% and 7.5% vol. of recycled aluminum added as a thermal conductivity enhancer to avoid sinking during the melting phase and to improve thermal conductivity. Recycled aluminum chips are inexpensive, abundant, and generate a lower environmental impact during composite production. The effect of the chip content was found to increase the thermal conductivity values of the composites by 100% (n-octadecane-Al short) and by 600% (n-octadecane-Al-long) compared to n-octadecane. The percentage of mass increase remained low. The latent heat of n-octadecane-Al-long decreased from 245 kJ/kg to 195 kJ/kg, the melting time shortened from 990 s to 850 s, and the CO2 emission reduction was by 150 kg CO2eq/year. The volume of the PCM composites varied from 0.083 m3 (n-octadecane) to 0.091 for n-octadecane-Al-long, which represents an increase of up to 11% needed to absorb the solar heat gained by the optimized PCM composite.
- 16 March 2017
- Published by Springer Nature
- p. 159-164
Modelling the Passive Behavior of the Nervous Cell. Influence of Electric Parameters Variation
- 16 March 2017
- Published by Springer Nature
- p. 159-164
Modelling the Passive Behavior of the Nervous Cell. Influence of Electric Parameters Variation
- 16 October 2015
- Published by Wiley in Artificial Organs
- Vol. 39 (10) , 841-848
Magnetic Stimulation of the Spinal Cord: Evaluating the Characteristics of an Appropriate Stimulator
This article aims to determine the necessary characteristics of a magnetic stimulator, capable of stimulating neural tracts of the spinal cord in a healthy subject. Our previous preliminary tests had shown that the commercial clinical magnetic stimulator Magstim Rapid2 was unable to reach excitable structures within the spinal cord, and only adjacent spinal nerves could be activated with the maximal deliverable field strength. In a subsequent modeling study, we were able to show that the “figure eight”‐shaped commercial coil could be one reason for, in this particular application, insufficient reach of the magnetic field, and substantial improvements could be gained by alternative geometrical arrangement of the windings of the magnetic coils. A further outcome was that a substantially higher driving voltage for the coil would be necessary to achieve activation of neural tracts within the spinal cord.
- 16 October 2015
- Published by Wiley in Artificial Organs
- Vol. 39 (10) , 841-848
Magnetic Stimulation of the Spinal Cord: Evaluating the Characteristics of an Appropriate Stimulator
This article aims to determine the necessary characteristics of a magnetic stimulator, capable of stimulating neural tracts of the spinal cord in a healthy subject. Our previous preliminary tests had shown that the commercial clinical magnetic stimulator Magstim Rapid2 was unable to reach excitable structures within the spinal cord, and only adjacent spinal nerves could be activated with the maximal deliverable field strength. In a subsequent modeling study, we were able to show that the “figure eight”‐shaped commercial coil could be one reason for, in this particular application, insufficient reach of the magnetic field, and substantial improvements could be gained by alternative geometrical arrangement of the windings of the magnetic coils. A further outcome was that a substantially higher driving voltage for the coil would be necessary to achieve activation of neural tracts within the spinal cord.