Hyoung Gwon Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Hyoung Gwon Choi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
Byoung Jin Jeon
LG Display, Virtual Fabricat Task, Seoul, South Korea
3 shared publicationsHyuk-Jae Chang
Yonsei University College of Medicine
1 shared publication- Sang-Jo Han
Seoul National University of Science and Technology
1 shared publication Seung-Ho Choi
1 shared publicationYo-Han Yoo
Agency for Defence Development
1 shared publication
Latest Publications
- Open Access
- 31 August 2021
- Published by Korean Society of Hazard Mitigation in Journal of the Korean Society of Hazard Mitigation
- Vol. 21 (4) , 121-127
Numerical Study on Extent of Hazardous Area for Sonic Jet Release Using Equivalent Leak Diameter
In this study, three-dimensional K - E turbulence numerical simulations were conducted to analyze the extent of hazardous area for the sonic jet leakage of flammable gas. Incompressible fluid flows were simulated based on an inlet boundary condition estimated using the theory of “equivalent leak diameter” to prevent the direct simulation of sonic flows near the leakage hole. Numerical simulations of 20 methane leakage scenarios providing the lower explosive limit contour showed shapes of the hazardous area with a maximum height of approximately 12-14 times larger than the maximum width, owing to convection. The extents of hazardous area determined using computational fluid dynamics (CFD) were approximately 5%-10% lower than the results obtained with 1 m over based on IEC 60079-10-1. For scenarios in which quantitative data were not calculated using IEC 60079-10-1 due to low release rates, CFD provided quantitative data for the extent of hazardous area, showing nonlinear relationships with the pressure and diameter of leak holes.
- 31 August 2021
- Published by Korean Society of Hazard Mitigation in Journal of the Korean Society of Hazard Mitigation
- Vol. 21 (4) , 121-127
Open AccessNumerical Study on Extent of Hazardous Area for Sonic Jet Release Using Equivalent Leak Diameter
In this study, three-dimensional K - E turbulence numerical simulations were conducted to analyze the extent of hazardous area for the sonic jet leakage of flammable gas. Incompressible fluid flows were simulated based on an inlet boundary condition estimated using the theory of “equivalent leak diameter” to prevent the direct simulation of sonic flows near the leakage hole. Numerical simulations of 20 methane leakage scenarios providing the lower explosive limit contour showed shapes of the hazardous area with a maximum height of approximately 12-14 times larger than the maximum width, owing to convection. The extents of hazardous area determined using computational fluid dynamics (CFD) were approximately 5%-10% lower than the results obtained with 1 m over based on IEC 60079-10-1. For scenarios in which quantitative data were not calculated using IEC 60079-10-1 due to low release rates, CFD provided quantitative data for the extent of hazardous area, showing nonlinear relationships with the pressure and diameter of leak holes.
- 31 October 2019
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - B
- Vol. 43 (10) , 699-706
Development of a Coloring Method for P2P1 Finite Element for Parallel Computation of ILU Preconditioner
본 연구에서는 Open-MP를 이용한 병렬연산의 수행 시에, coloring 기법이 순차적인 연산이 요구되는 병렬 ILU 연산의 성능에 미치는 영향을 고찰하였다. Coloring 기법은 비압축성 Navier-Stokes 방정식의 이산화를 위하여 사용한 P2P1 유한요소를 위하여 개발하였다. 개발된 알고리즘을 이용하여 3차원 열전도 문제와 3차원 비대칭 협착관 문제를 해석하고, 다양한 격자계에 대해서 컬러링이 적용되지 않은 ILU 행렬의 단일 코어 연산시간과의 비교를 통해 Open-MP 병렬연산의 성능 향상을 측정하였다. 컬러링을 적용한 정렬 격자계의 단일 코어 연산시간은 컬러링 전보다 느려질 수 있으나, 비정렬 격자계는 메모리 접근성이 좋아지기 때문에, 단일 코어 연산시간은 컬러링 전보다 빨라질 수 있음을 확인하였다. 제안된 기법의 3차원 표준예제들에 대한 검증에서 정렬 격자계와 비정렬 격자계는 각각 약 4배와 8배의 속도향상을 주었다.
- 31 October 2019
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - B
- Vol. 43 (10) , 699-706
Development of a Coloring Method for P2P1 Finite Element for Parallel Computation of ILU Preconditioner
본 연구에서는 Open-MP를 이용한 병렬연산의 수행 시에, coloring 기법이 순차적인 연산이 요구되는 병렬 ILU 연산의 성능에 미치는 영향을 고찰하였다. Coloring 기법은 비압축성 Navier-Stokes 방정식의 이산화를 위하여 사용한 P2P1 유한요소를 위하여 개발하였다. 개발된 알고리즘을 이용하여 3차원 열전도 문제와 3차원 비대칭 협착관 문제를 해석하고, 다양한 격자계에 대해서 컬러링이 적용되지 않은 ILU 행렬의 단일 코어 연산시간과의 비교를 통해 Open-MP 병렬연산의 성능 향상을 측정하였다. 컬러링을 적용한 정렬 격자계의 단일 코어 연산시간은 컬러링 전보다 느려질 수 있으나, 비정렬 격자계는 메모리 접근성이 좋아지기 때문에, 단일 코어 연산시간은 컬러링 전보다 빨라질 수 있음을 확인하였다. 제안된 기법의 3차원 표준예제들에 대한 검증에서 정렬 격자계와 비정렬 격자계는 각각 약 4배와 8배의 속도향상을 주었다.
- 21 June 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (6) , 2651-2658
A numerical study on the effect of trapezium stenosis shape on the axisymmetric flow field around stenosis
- 21 June 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (6) , 2651-2658
A numerical study on the effect of trapezium stenosis shape on the axisymmetric flow field around stenosis
- 25 October 2013
- Published by Springer Nature in Personal and Ubiquitous Computing
- Vol. 18 (6) , 1303-1314
Investigation of the parallel efficiency of a PC cluster for the simulation of a CFD problem
- 25 October 2013
- Published by Springer Nature in Personal and Ubiquitous Computing
- Vol. 18 (6) , 1303-1314
Investigation of the parallel efficiency of a PC cluster for the simulation of a CFD problem