Shirin Shahrbaf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shirin Shahrbaf has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Nicolas Martin
School of Clinical Dentistry University of Sheffield Sheffield UK
4 shared publications - Behnam Mirzakouchaki
School of Dentistry, Division of Orthodontics, Tabriz University of Medical Sciences, Tabriz, Iran
3 shared publications Elaheh Ghassemieh
School of Mechanical and Aerospace Engineering, Queen's University of Belfast, Ashby Building, Room 3020, Stranmillis Road, Belfast, BT9 5AH, UK
2 shared publications- Azeem Ul Yaqin Syed
Department of Prosthodontics, College of Dentistry, University of Science and Technology of Fujairah, Fujairah P.O. Box 2202, United Arab Emirates
1 shared publication Babak Bahrami
Division of Biomechanics, Department of Mechanical Engineering, Sahand University of Technology, Tabriz, Iran
1 shared publication- Dinesh Rokaya
Clinical Sciences Department, College of Dentistry, Ajman University, Ajman, United Arab Emirates
1 shared publication
Latest Publications
- Open Access
- 29 January 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (3) , 1220
Three-Dimensional Finite Element Analysis of Stress Distribution in a Tooth Restored with Full Coverage Machined Polymer Crown
The effect of a restored machined hybrid dental ceramic crown–tooth complex is not well understood. This study was conducted to determine the effect of the stress state of the machined hybrid dental ceramic crown using three-dimensional finite element analysis. Human premolars were prepared to receive full coverage crowns and restored with machined hybrid dental ceramic crowns using the resin cement. Then, the teeth were digitized using micro-computed tomography and the teeth were scanned with an optical intraoral scanner using an intraoral scanner. Three-dimensional digital models were generated using an interactive image processing software for the restored tooth complex. The generated models were imported into a finite element analysis software with all degrees of freedom concentrated on the outer surface of the root of the crown–tooth complex. To simulate average occlusal load subjected on a premolar a total load of 300 N was applied, 150 N at a buccal incline of the palatal cusp, and palatal incline of the buccal cusp. The von Mises stresses were calculated for the crown–tooth complex under simulated load application was determined. Three-dimensional finite element analysis showed that the stress distribution was more in the dentine and least in the cement. For the cement layer, the stresses were more concentrated on the buccal cusp tip. In dentine, stress was more on the cusp tips and coronal 1/3 of the root surface. The conventional crown preparation is a suitable option for machined polymer crowns with less stress distribution within the crown–tooth complex and can be a good aesthetic replacement in the posterior region. Enamic crowns are a good viable option in the posterior region.
- 29 January 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (3) , 1220
Open AccessThree-Dimensional Finite Element Analysis of Stress Distribution in a Tooth Restored with Full Coverage Machined Polymer Crown
The effect of a restored machined hybrid dental ceramic crown–tooth complex is not well understood. This study was conducted to determine the effect of the stress state of the machined hybrid dental ceramic crown using three-dimensional finite element analysis. Human premolars were prepared to receive full coverage crowns and restored with machined hybrid dental ceramic crowns using the resin cement. Then, the teeth were digitized using micro-computed tomography and the teeth were scanned with an optical intraoral scanner using an intraoral scanner. Three-dimensional digital models were generated using an interactive image processing software for the restored tooth complex. The generated models were imported into a finite element analysis software with all degrees of freedom concentrated on the outer surface of the root of the crown–tooth complex. To simulate average occlusal load subjected on a premolar a total load of 300 N was applied, 150 N at a buccal incline of the palatal cusp, and palatal incline of the buccal cusp. The von Mises stresses were calculated for the crown–tooth complex under simulated load application was determined. Three-dimensional finite element analysis showed that the stress distribution was more in the dentine and least in the cement. For the cement layer, the stresses were more concentrated on the buccal cusp tip. In dentine, stress was more on the cusp tips and coronal 1/3 of the root surface. The conventional crown preparation is a suitable option for machined polymer crowns with less stress distribution within the crown–tooth complex and can be a good aesthetic replacement in the posterior region. Enamic crowns are a good viable option in the posterior region.
- 1 April 2014
- Published by Elsevier in Dental Materials
- Vol. 30 (4) , e89-e97
Effect of surface treatment on stress distribution in immediately loaded dental implants—A 3D finite element analysis
- 1 April 2014
- Published by Elsevier in Dental Materials
- Vol. 30 (4) , e89-e97
Effect of surface treatment on stress distribution in immediately loaded dental implants—A 3D finite element analysis
- 1 February 2014
- Published by Elsevier in Dental Materials
- Vol. 30 (2) , 234-241
Fracture strength of machined ceramic crowns as a function of tooth preparation design and the elastic modulus of the cement
- 1 February 2014
- Published by Elsevier in Dental Materials
- Vol. 30 (2) , 234-241
Fracture strength of machined ceramic crowns as a function of tooth preparation design and the elastic modulus of the cement
- 1 August 2013
- Published by Elsevier in Dental Materials
- Vol. 29 (8) , e123-e131
Effect of the crown design and interface lute parameters on the stress-state of a machined crown–tooth system: A finite element analysis
- 1 August 2013
- Published by Elsevier in Dental Materials
- Vol. 29 (8) , e123-e131
Effect of the crown design and interface lute parameters on the stress-state of a machined crown–tooth system: A finite element analysis