David L. Reuss
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
David L. Reuss has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Volker Sick
University of Michigan, Mechanical Engineering, Ann Arbor, MI, USA
3 shared publications - Angela Wu
Sandia National Laboratories, Livermore, CA, USA
1 shared publication - Mark L. Greene
Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109
1 shared publication - P. Schiffmann
University of Michigan, 1231 Beal Ave, 2045 Auto Lab, Ann Arbor, MI 48109 – USA
1 shared publication Philipp Schiffmann
IFP Energies nouvelles, Rueil-Malmaison, France
1 shared publicationPreeti S. Abraham
Department of Mechanical Engineering The University of Michigan Ann Arbor MI USA
1 shared publication
Latest Publications
- 28 June 2019
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 141 (12)
Comparison of Near-Wall Flow and Heat Transfer of an Internal Combustion Engine Using Particle Image Velocimetry and Computational Fluid Dynamics
In this study, computational fluid dynamics (CFD) modeling capability of near-wall flow and heat transfer was evaluated against experimental data. Industry-standard wall models for RANS and large-eddy simulation (LES) (law of the wall) were examined against the near-wall flow and heat flux measurements from the transparent combustion chamber (TCC-III) engine. The study shows that the measured, normalized velocity profile does not follow the law of the wall. This wall model, which provides boundary conditions for the simulations, failed to predict the measured velocity profiles away from the wall. LES showed a reasonable prediction in peak heat flux and peak in-cylinder pressure to the experiment, while RANS-heat flux was closer to experimental heat flux but lower in peak pressure. The measurement resolution is higher than that of the simulations, indicating that higher spatial resolution for CFD is needed near the wall to accurately represent the flow and heat transfer. Near-wall mesh refinement was then performed in LES. The wall-normal velocity from the refined mesh case matches better with measurements compared with the wall-parallel velocity. Mesh refinement leads to a normalized velocity profile that matches with measurement in trend only. In addition, the heat flux and its peak value matches well with the experimental heat flux compared with the base mesh.
- 28 June 2019
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 141 (12)
Comparison of Near-Wall Flow and Heat Transfer of an Internal Combustion Engine Using Particle Image Velocimetry and Computational Fluid Dynamics
In this study, computational fluid dynamics (CFD) modeling capability of near-wall flow and heat transfer was evaluated against experimental data. Industry-standard wall models for RANS and large-eddy simulation (LES) (law of the wall) were examined against the near-wall flow and heat flux measurements from the transparent combustion chamber (TCC-III) engine. The study shows that the measured, normalized velocity profile does not follow the law of the wall. This wall model, which provides boundary conditions for the simulations, failed to predict the measured velocity profiles away from the wall. LES showed a reasonable prediction in peak heat flux and peak in-cylinder pressure to the experiment, while RANS-heat flux was closer to experimental heat flux but lower in peak pressure. The measurement resolution is higher than that of the simulations, indicating that higher spatial resolution for CFD is needed near the wall to accurately represent the flow and heat transfer. Near-wall mesh refinement was then performed in LES. The wall-normal velocity from the refined mesh case matches better with measurements compared with the wall-parallel velocity. Mesh refinement leads to a normalized velocity profile that matches with measurement in trend only. In addition, the heat flux and its peak value matches well with the experimental heat flux compared with the base mesh.
- 26 July 2017
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 19 (5) , 491-508
Empirical investigation of spark-ignited flame-initiation cycle-to-cycle variability in a homogeneous charge reciprocating engine
This experimental study investigates the flame-initiation period variability in the spark-ignited homogeneous charge third-generation transparent combustion chamber optical engine. The engine was operated with lean, rich, and stoichiometric, propane and methane, with and without nitrogen dilution. These operating conditions were chosen to systematically change the unstretched laminar flame velocity and the Markstein number. Traditional pressure measures, apparent heat release analysis, particle image velocimetry, and OH* flame imaging were used to generate over 400 metrics for 750 cycles at each of the 34 tests at 11 operating conditions. A multivariate statistical analysis was used to identify the parameters important to the variability of the crank angle at 10% fuel mass fraction burned but could not reveal physical mechanisms or cause and effect. The analysis here revealed that the combustion-phasing cycle-to-cycle variability is established by the time of the notional laminar-to-turbulent flame transition that occurs by 1% mass burn fraction, measured here from the flame image growth. Both the Markstein number and stretched laminar flame speed were found to be important. The velocity magnitude and direction were found to correlate with fast and slow 10% fuel mass fraction burned as found in early literature. It was also revealed that the shear strength, a property of the strain rate tensor at the scales resolved here (1 mm), deserves further investigation as a possible effect on 10% fuel mass fraction burned.
- 26 July 2017
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 19 (5) , 491-508
Empirical investigation of spark-ignited flame-initiation cycle-to-cycle variability in a homogeneous charge reciprocating engine
This experimental study investigates the flame-initiation period variability in the spark-ignited homogeneous charge third-generation transparent combustion chamber optical engine. The engine was operated with lean, rich, and stoichiometric, propane and methane, with and without nitrogen dilution. These operating conditions were chosen to systematically change the unstretched laminar flame velocity and the Markstein number. Traditional pressure measures, apparent heat release analysis, particle image velocimetry, and OH* flame imaging were used to generate over 400 metrics for 750 cycles at each of the 34 tests at 11 operating conditions. A multivariate statistical analysis was used to identify the parameters important to the variability of the crank angle at 10% fuel mass fraction burned but could not reveal physical mechanisms or cause and effect. The analysis here revealed that the combustion-phasing cycle-to-cycle variability is established by the time of the notional laminar-to-turbulent flame transition that occurs by 1% mass burn fraction, measured here from the flame image growth. Both the Markstein number and stretched laminar flame speed were found to be important. The velocity magnitude and direction were found to correlate with fast and slow 10% fuel mass fraction burned as found in early literature. It was also revealed that the shear strength, a property of the strain rate tensor at the scales resolved here (1 mm), deserves further investigation as a possible effect on 10% fuel mass fraction burned.
- Open Access
- 27 October 2015
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 71 (1) , 3
TCC-III Engine Benchmark for Large-Eddy Simulation of IC Engine Flows
Oil & Gas Science and Technology - Revue d'IFP Energies nouvelles
- 27 October 2015
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 71 (1) , 3
Open AccessTCC-III Engine Benchmark for Large-Eddy Simulation of IC Engine Flows
Oil & Gas Science and Technology - Revue d'IFP Energies nouvelles
- Open Access
Flow-pattern switching in a Motored Spark Ignition Engine
Cyclic-to-cycle variability, CCV, of intake-jet flow in an optical engine was measured using particle image velocimetry (PIV), revealing the possibility of two different flow patterns. A phase-dependent proper orthogonal decomposition (POD) analysis showed that one or the other flow pattern would appear in the average flow, sampled from test to test or sub-sampled within a single test; each data set contained individual cycles showing one flow pattern or the other. Three-dimensional velocity data from a large-eddy simulation (LES) of the engine showed that the PIV plane was cutting through a region of high shear between the intake jet and another large flow structure. Rotating the measurement plane 10{\deg} revealed one or the other flow structure observed in the PIV measurements. Thus, it was hypothesized that cycle-to-cycle variations in the swirl ratio result in the two different flow patterns in the PIV plane. Having an unambiguous metric to reveal large-scale flow CCV, causes for this variability were examined within the possible sources present in the available testing. In particular, variations in intake-port and cylinder pressure, lateral valve oscillations, and engine RPM were examined as potential causes for the cycle-to-cycle flow ariations using the phase-dependent POD coefficients. No direct correlation was seen between the intake port pressure, or the pressure drop across the intake valve, and the in-cylinder flow pattern. A correlation was observed between dominant flow pattern and cycle-to-cycle variations in intake valve horizontal position. RPM values and in-cylinder flow patterns did not correlate directly. However, a shift in flow pattern was observed between early and late cycles in a 2900-cycle test after an approximately 5 rpm engine speed perturbation.
Open AccessFlow-pattern switching in a Motored Spark Ignition Engine
Cyclic-to-cycle variability, CCV, of intake-jet flow in an optical engine was measured using particle image velocimetry (PIV), revealing the possibility of two different flow patterns. A phase-dependent proper orthogonal decomposition (POD) analysis showed that one or the other flow pattern would appear in the average flow, sampled from test to test or sub-sampled within a single test; each data set contained individual cycles showing one flow pattern or the other. Three-dimensional velocity data from a large-eddy simulation (LES) of the engine showed that the PIV plane was cutting through a region of high shear between the intake jet and another large flow structure. Rotating the measurement plane 10{\deg} revealed one or the other flow structure observed in the PIV measurements. Thus, it was hypothesized that cycle-to-cycle variations in the swirl ratio result in the two different flow patterns in the PIV plane. Having an unambiguous metric to reveal large-scale flow CCV, causes for this variability were examined within the possible sources present in the available testing. In particular, variations in intake-port and cylinder pressure, lateral valve oscillations, and engine RPM were examined as potential causes for the cycle-to-cycle flow ariations using the phase-dependent POD coefficients. No direct correlation was seen between the intake port pressure, or the pressure drop across the intake valve, and the in-cylinder flow pattern. A correlation was observed between dominant flow pattern and cycle-to-cycle variations in intake valve horizontal position. RPM values and in-cylinder flow patterns did not correlate directly. However, a shift in flow pattern was observed between early and late cycles in a 2900-cycle test after an approximately 5 rpm engine speed perturbation.