Moble Benedict
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Moble Benedict has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Inderjit Chopra
University of Maryland, College Park, Maryland 20740
5 shared publications - Vikram Hrishikeshavan
Assistant Research Scientist
2 shared publications David B. Mayo
1 shared publicationDavid Coleman
1 shared publicationElena Shrestha
Department of Aerospace Engineering, University of Maryland, College Park, Maryland 20742
1 shared publicationPranay Seshadri
Department of Engineering, University of Cambridge, Cambridge, England CB2 1PZ, United Kingdom
1 shared publication
Latest Publications
- 1 April 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 54 (4) , 1145-1157
Experiments on Rigid Wing Undergoing Hover-Capable Flapping Kinematics at Micro-Air-Vehicle-Scale Reynolds Numbers
The paper focuses on understanding the mechanism of force production on a hover-capable flapping-wing system by using a combination of direct force measurements and flowfield studies. The experiments were conducted in air at a Reynolds number of approximately 25,000 (based on mean chord and maximum tip speed), which is the typical operating regime of small flapping-wing micro air vehicles. The forces and moments were measured using a miniature six-component force transducer installed at the wing root. The wing was flapped in air and vacuum at the same frequency and wing kinematics, and the vacuum forces were subtracted from the total forces to obtain the pure aerodynamic forces. Flow visualization and particle image velocimetry were used to characterize the formation, strength, and structure of the leading-edge vortex on the flapping wing. A rapid increase in wing lift coefficient was associated with the growth of the leading-edge vortex and a progressive reduction in lift coefficient with the convection of the leading-edge vortex over the chord. The leading-edge vortex was observed to be stable for the spanwise locations closer to the root (i.e., the 25% span location) and burst for locations away from the root (50 and 75% span locations) just after the midstroke. High instantaneous lift coefficient values () were measured during the translational phase, clearly showing the role of leading-edge vortex in augmenting lift. However, lift-to-drag ratios were always less than 1. Aerodynamic efficiency during the translational phase was quantified in terms of figure of merit, which improved with decreasing translational wing pitch angle. The maximum figure of merit value measured was 0.36 at 40 deg translational pitch angle.- 1 April 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 54 (4) , 1145-1157
Experiments on Rigid Wing Undergoing Hover-Capable Flapping Kinematics at Micro-Air-Vehicle-Scale Reynolds Numbers
The paper focuses on understanding the mechanism of force production on a hover-capable flapping-wing system by using a combination of direct force measurements and flowfield studies. The experiments were conducted in air at a Reynolds number of approximately 25,000 (based on mean chord and maximum tip speed), which is the typical operating regime of small flapping-wing micro air vehicles. The forces and moments were measured using a miniature six-component force transducer installed at the wing root. The wing was flapped in air and vacuum at the same frequency and wing kinematics, and the vacuum forces were subtracted from the total forces to obtain the pure aerodynamic forces. Flow visualization and particle image velocimetry were used to characterize the formation, strength, and structure of the leading-edge vortex on the flapping wing. A rapid increase in wing lift coefficient was associated with the growth of the leading-edge vortex and a progressive reduction in lift coefficient with the convection of the leading-edge vortex over the chord. The leading-edge vortex was observed to be stable for the spanwise locations closer to the root (i.e., the 25% span location) and burst for locations away from the root (50 and 75% span locations) just after the midstroke. High instantaneous lift coefficient values () were measured during the translational phase, clearly showing the role of leading-edge vortex in augmenting lift. However, lift-to-drag ratios were always less than 1. Aerodynamic efficiency during the translational phase was quantified in terms of figure of merit, which improved with decreasing translational wing pitch angle. The maximum figure of merit value measured was 0.36 at 40 deg translational pitch angle.- 1 March 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 51 (2) , 672-676
Development of a Micro Twin-Rotor Cyclocopter Capable of Autonomous Hover
- 1 March 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 51 (2) , 672-676
Development of a Micro Twin-Rotor Cyclocopter Capable of Autonomous Hover
- 1 July 2013
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 50 (4) , 1070-1087
Understanding Micro Air Vehicle Flapping-Wing Aerodynamics Using Force and Flowfield Measurements
- 1 July 2013
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 50 (4) , 1070-1087
Understanding Micro Air Vehicle Flapping-Wing Aerodynamics Using Force and Flowfield Measurements
- Open Access
- 1 June 2013
- Published by SAGE Publications in International Journal of Micro Air Vehicles
- Vol. 5 (2) , 145-162
Design, Development, and Flight Test of a Small-Scale Cyclogyro UAV Utilizing a Novel Cam-Based Passive Blade Pitching Mechanism
A cycloidal rotor is an innovative horizontal axis propulsion system, which is utilized in the present study to develop a fully-controllable flying aircraft (known as “Cyclogyro”). The present 535 gram cyclogyro uses a hybrid configuration with two cyclorotors and a horizontal tail rotor. Since a cycloidal rotor relies on cyclic blade pitching for producing thrust and also for control, designing a reliable pitch mechanism that can provide the required blade pitching kinematics (depending on the advance ratio) is extremely important. A novel blade pitch mechanism has been developed, which is passively driven by centrifugal force, and could potentially be adapted to generate the required pitching schedules for efficient operation over a range of advance ratios. A simplified flightworthy version of this mechanism was implemented in the present cyclogyro. The mechanism was able to generate the appropriate blade kinematics and the thrust required for the vehicle to hover. Also, the present mechanism is designed such that it is possible to vary both amplitude and phasing of the cyclic blade pitching. A novel control strategy was developed using blade pitch amplitude (thrust magnitude) control for roll, phasing (thrust direction) for yaw and tail rotor for pitch control. The control strategy was implemented using a three gram onboard processor, which was used to stabilize the vehicle without a pilot, through a closed-loop feedback control system. This is the first flight-capable cyclogyro reported in the literature to utilize cycloidal rotors having both pitch amplitude and phase control. The successful flight for the present vehicle also validates the flightworthiness of this completely passive pitch mechanism design, which has great potential for efficient forward flight.
- 1 June 2013
- Published by SAGE Publications in International Journal of Micro Air Vehicles
- Vol. 5 (2) , 145-162
Open AccessDesign, Development, and Flight Test of a Small-Scale Cyclogyro UAV Utilizing a Novel Cam-Based Passive Blade Pitching Mechanism
A cycloidal rotor is an innovative horizontal axis propulsion system, which is utilized in the present study to develop a fully-controllable flying aircraft (known as “Cyclogyro”). The present 535 gram cyclogyro uses a hybrid configuration with two cyclorotors and a horizontal tail rotor. Since a cycloidal rotor relies on cyclic blade pitching for producing thrust and also for control, designing a reliable pitch mechanism that can provide the required blade pitching kinematics (depending on the advance ratio) is extremely important. A novel blade pitch mechanism has been developed, which is passively driven by centrifugal force, and could potentially be adapted to generate the required pitching schedules for efficient operation over a range of advance ratios. A simplified flightworthy version of this mechanism was implemented in the present cyclogyro. The mechanism was able to generate the appropriate blade kinematics and the thrust required for the vehicle to hover. Also, the present mechanism is designed such that it is possible to vary both amplitude and phasing of the cyclic blade pitching. A novel control strategy was developed using blade pitch amplitude (thrust magnitude) control for roll, phasing (thrust direction) for yaw and tail rotor for pitch control. The control strategy was implemented using a three gram onboard processor, which was used to stabilize the vehicle without a pilot, through a closed-loop feedback control system. This is the first flight-capable cyclogyro reported in the literature to utilize cycloidal rotors having both pitch amplitude and phase control. The successful flight for the present vehicle also validates the flightworthiness of this completely passive pitch mechanism design, which has great potential for efficient forward flight.
- 8 June 2012
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 7 (3) , 036017
A novel mechanism for emulating insect wing kinematics
A novel dual-differential four-bar flapping mechanism that can accurately emulate insect wing kinematics in all three degrees of freedom (translation, rotation and stroke plane deviation) is developed. The mechanism is specifically designed to be simple and scalable such that it can be utilized on an insect-based flapping wing micro air vehicle. Kinematic formulations for the wing stroke position, pitch angle and coning angle for this model are derived from first principles and compared with a 3D simulation. A benchtop flapping mechanism based on this model was designed and built, which was also equipped with a balance for force measurements. 3D motion capture tests were conducted on this setup to demonstrate the capability of generating complex figure-of-eight flapping motions along with dynamic pitching. The dual-differential four-bar mechanism was implemented on a light-weight vehicle that demonstrated tethered hover.
- 8 June 2012
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 7 (3) , 036017
A novel mechanism for emulating insect wing kinematics
A novel dual-differential four-bar flapping mechanism that can accurately emulate insect wing kinematics in all three degrees of freedom (translation, rotation and stroke plane deviation) is developed. The mechanism is specifically designed to be simple and scalable such that it can be utilized on an insect-based flapping wing micro air vehicle. Kinematic formulations for the wing stroke position, pitch angle and coning angle for this model are derived from first principles and compared with a 3D simulation. A benchtop flapping mechanism based on this model was designed and built, which was also equipped with a balance for force measurements. 3D motion capture tests were conducted on this setup to demonstrate the capability of generating complex figure-of-eight flapping motions along with dynamic pitching. The dual-differential four-bar mechanism was implemented on a light-weight vehicle that demonstrated tethered hover.