Selçuk Demirezen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Selçuk Demirezen has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Ş. Altındal
Physics Department, Faculty of Sciences, Gazi University, Ankara, Turkey
6 shared publicationsH. G. Çetinkaya
Vocational School of Health Services, Gazi University, Ankara, Turkey
3 shared publicationsYashar Azizian-Kalandaragh
Department of Photonics, Faculty of Applied Sciences, Gazi University, Ankara, Turkey
3 shared publicationsŞemsettin Altındal
Department of Physics, Faculty of Science, Gazi University, Ankara, Turkey
3 shared publicationsA. Dere
Vocational School of Technical Science, Department of Electric and Energy, Firat University, Elazig, Turkey
2 shared publicationsAyşegül Eroğlu
Department of Physics, Faculty of Science, Gazi University, Ankara, Turkey
2 shared publications
Latest Publications
- 1 October 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (10) , 105968
Iron phthalocyanine(FePc)-sensitized ZnO for enhanced photovoltaic and electronic performance
Iron phthalocyanine (FePc)-incorporated zinc oxide (ZnO) interfacial Al/p-Si Schottky barrier diodes (SBDs) were fabricated by spin-coating methodology. The aim of this research was to evaluate the effect of FePc concentration variations on the electrical and photoresponsive properties of these heterojunction devices. The experimental process included current–voltage ( I-V ) characterization over several FePc doping concentrations (0.05 wt%, 0.1 wt%, 0.2 wt%) under voltage ranges of ±5V and variable illumination conditions (from 10 mW cm −2 to 100 mW cm −2 ). These measurements enabled the extraction of essential electrical properties, such as the ideality factor (n), barrier height (Φ B ), series resistance ( R s ), shunt resistance ( R sh ), and interface state density ( N ss ), under both dark conditions and varying illumination intensities between 10 and 100 mW cm −2 . The observed increase in reverse current with increasing light intensity demonstrated the potential applications of these structures in photodetection technologies. The fabricated devices exhibited linear dynamic range (LDR) values of approximately 16 across all configurations, which is a crucial factor for image sensors, and achieved rectification ratios (RR) on the order of 10 3 . Experimental results showed that the rectification behavior could be modulated by adjusting the FePc concentration. Furthermore, significant correlations were observed between FePc content and the values of n, Φ B , R s , R sh and N ss . Capacitance–voltage ( C-V ) and conductance-voltage ( G-V ) measurements were performed at 1 kHz and 1 MHz to extract additional parameters including diffusion potential ( V D ), acceptor concentration ( N A ), Fermi energy level ( E F ) and depletion width ( W D ). Frequency-dependent capacitance behaviour was observed, with higher values recorded at lower frequencies due to the influence of interfacial states. The comprehensive analysis suggests that these FePc-doped structures hold considerable promise for optoelectronic applications, including photodetection and optical sensing, with performance characteristics that can be engineered by systematically modulating the FePc concentration within the ZnO interlayer framework.
- 1 October 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (10) , 105968
Iron phthalocyanine(FePc)-sensitized ZnO for enhanced photovoltaic and electronic performance
Iron phthalocyanine (FePc)-incorporated zinc oxide (ZnO) interfacial Al/p-Si Schottky barrier diodes (SBDs) were fabricated by spin-coating methodology. The aim of this research was to evaluate the effect of FePc concentration variations on the electrical and photoresponsive properties of these heterojunction devices. The experimental process included current–voltage ( I-V ) characterization over several FePc doping concentrations (0.05 wt%, 0.1 wt%, 0.2 wt%) under voltage ranges of ±5V and variable illumination conditions (from 10 mW cm −2 to 100 mW cm −2 ). These measurements enabled the extraction of essential electrical properties, such as the ideality factor (n), barrier height (Φ B ), series resistance ( R s ), shunt resistance ( R sh ), and interface state density ( N ss ), under both dark conditions and varying illumination intensities between 10 and 100 mW cm −2 . The observed increase in reverse current with increasing light intensity demonstrated the potential applications of these structures in photodetection technologies. The fabricated devices exhibited linear dynamic range (LDR) values of approximately 16 across all configurations, which is a crucial factor for image sensors, and achieved rectification ratios (RR) on the order of 10 3 . Experimental results showed that the rectification behavior could be modulated by adjusting the FePc concentration. Furthermore, significant correlations were observed between FePc content and the values of n, Φ B , R s , R sh and N ss . Capacitance–voltage ( C-V ) and conductance-voltage ( G-V ) measurements were performed at 1 kHz and 1 MHz to extract additional parameters including diffusion potential ( V D ), acceptor concentration ( N A ), Fermi energy level ( E F ) and depletion width ( W D ). Frequency-dependent capacitance behaviour was observed, with higher values recorded at lower frequencies due to the influence of interfacial states. The comprehensive analysis suggests that these FePc-doped structures hold considerable promise for optoelectronic applications, including photodetection and optical sensing, with performance characteristics that can be engineered by systematically modulating the FePc concentration within the ZnO interlayer framework.
- Open Access
- 22 May 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (14) , 1-19
Interface and dielectric properties of Al/p-Si diode by organic composite interlayer for MOS
Thin films with different ratios (0, 0.5, and 2 wt%) of GO-doped P3HT:PCBM were synthesized on p-Si wafers using the spin coating technique to create Al/GO:P3HT:PCBM/p-Si structures. In order to comprehensively investigate the effect of GO doping on P3HT:PCBM in terms of AC electrical conductivity (σ ac), complex permittivity (ε*), complex electric modulus (M*), and complex impedance (Z*), we have performed capacitance/conductance-voltage (C/G-V) measurements on Al/GO:P3HT:PCBM/p-Si structures over a wide range of frequencies and voltages. Different ratios (0, 0.5, and 2 wt%) of GO in P3HT:PCBM layers were deposited on a p-type Si wafer as an interlayer. The values of the complex dielectric constant/loss (εʹ/ε″), the loss tangent (tanδ), the AC electrical conductivity (σ ac), and the real/imaginary components of the complex electric modulus (Mʹ, M″) were determined from the C/G-V measurements as a function of frequency, ranging from 0.5 to 2.5 V with 100 mV steps. All parameters showed distinct frequency/voltage dependencies, surface/dipole polarizations, and interlayer effects, especially at low and intermediate frequencies. In particular, the elevated dielectric constants measured (approximately 52 for 0.5% GO concentration and 60 for 2% GO concentration) at frequencies as high as 10 kHz indicate that GO:P3HT thin films are a viable alternative to conventional SiO2 dielectrics. The real component of the dielectric permittivity maintained at 10 kHz exceeds that of conventional SiO2 insulators (3.8) by a factor of 16, demonstrating the superior charge storage capacity of these composite films and their potential to replace standard insulators in energy storage applications. Furthermore, the value of σ ac increased with increasing doping rate of GO, indicating potential advantages of using high-dielectric organic thin films between metal and semiconductor instead of conventional metal/oxide/semiconductor (MOS) structures. The plot of ln(σₐₐ) as a function of ln(f) for the synthesized structures reveals two distinct linear regions, each characterized by varying slopes. This finding indicates the presence of two independent conduction mechanisms operating within the structures at ambient temperature. Moreover, the M″ exhibits a significant peak, the location of which advances toward higher frequencies as the applied voltage increases. This peak phenomenon can be ascribed to a diminution in polarization effects alongside contributions arising from interfacial or surface states.
- 22 May 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (14) , 1-19
Open AccessInterface and dielectric properties of Al/p-Si diode by organic composite interlayer for MOS
Thin films with different ratios (0, 0.5, and 2 wt%) of GO-doped P3HT:PCBM were synthesized on p-Si wafers using the spin coating technique to create Al/GO:P3HT:PCBM/p-Si structures. In order to comprehensively investigate the effect of GO doping on P3HT:PCBM in terms of AC electrical conductivity (σ ac), complex permittivity (ε*), complex electric modulus (M*), and complex impedance (Z*), we have performed capacitance/conductance-voltage (C/G-V) measurements on Al/GO:P3HT:PCBM/p-Si structures over a wide range of frequencies and voltages. Different ratios (0, 0.5, and 2 wt%) of GO in P3HT:PCBM layers were deposited on a p-type Si wafer as an interlayer. The values of the complex dielectric constant/loss (εʹ/ε″), the loss tangent (tanδ), the AC electrical conductivity (σ ac), and the real/imaginary components of the complex electric modulus (Mʹ, M″) were determined from the C/G-V measurements as a function of frequency, ranging from 0.5 to 2.5 V with 100 mV steps. All parameters showed distinct frequency/voltage dependencies, surface/dipole polarizations, and interlayer effects, especially at low and intermediate frequencies. In particular, the elevated dielectric constants measured (approximately 52 for 0.5% GO concentration and 60 for 2% GO concentration) at frequencies as high as 10 kHz indicate that GO:P3HT thin films are a viable alternative to conventional SiO2 dielectrics. The real component of the dielectric permittivity maintained at 10 kHz exceeds that of conventional SiO2 insulators (3.8) by a factor of 16, demonstrating the superior charge storage capacity of these composite films and their potential to replace standard insulators in energy storage applications. Furthermore, the value of σ ac increased with increasing doping rate of GO, indicating potential advantages of using high-dielectric organic thin films between metal and semiconductor instead of conventional metal/oxide/semiconductor (MOS) structures. The plot of ln(σₐₐ) as a function of ln(f) for the synthesized structures reveals two distinct linear regions, each characterized by varying slopes. This finding indicates the presence of two independent conduction mechanisms operating within the structures at ambient temperature. Moreover, the M″ exhibits a significant peak, the location of which advances toward higher frequencies as the applied voltage increases. This peak phenomenon can be ascribed to a diminution in polarization effects alongside contributions arising from interfacial or surface states.
- Open Access
- 12 May 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (14) , 1-20
Investigation of hybrid CuPc-doped ZnO/p-silicon photodiodes for photonic and electronic applications
Copper phthalocyanine (CuPc) doped zinc oxide (ZnO) interlayered Al/p-Si Schottky barrier diodes (SBDs) were systematically fabricated utilizing spin coating technique. This study was undertaken to meticulously assess the influence of varying concentrations of CuPc on the intricate electrical and photodiode characteristics of these devices. The investigation involved the characterization of the current–voltage (I–V) characteristics configured with distinct different doping concentrations of CuPc such as 0.05 wt%,1 wt%, 2 wt%, under a wide range of voltages (± 5 V) and illumination irradiances. These measurements enabled the calculation of various critical electrical variables, such as the ideality factor (n), barrier height (ΦB), series resistance (Rs), shunt resistance (Rsh), interface states density (Nss) and their response under various illumination levels (between 10 and 100 mW/cm2) and under dark condition. An increase in the reverse current as the illumination increases suggested the potential utility of these SBDs as photodiodes, photosensors, or photodetectors. Notably, the linear dynamic range (LDR), a crucial factor for image sensors which obtained around 14 for all photodiodes. The photodiodes exhibited a good rectification ratio (RR) of approximately 104. The results obtained indicate that the rectifying properties of the structures can be controlled by CuPc doping. In addition, the results indicated that the presence of CuPc significantly influenced the values of n, ΦB, Rs/Rsh, and Nss. To further analyze the devices, capacitance–voltage (C–V) and conductance–voltage (G–V) measurements were carried out to determine parameters such as diffusion potential (VD), dopant acceptor atoms concentration (NA), Fermi energy level (EF), and width of depletion layer (WD) at both 1 kHz and 1 MHz. The measurements revealed that the capacitance values were higher at low frequencies compared to high frequencies, and this behavior was attributed to Nss. In summary, this study suggests that the manufactured photodiodes have the potential to be employed as photodiodes, sensors, or detectors in optical sensing applications, and their performance can be tailored by adjusting the concentration of CuPc in the ZnO interlayered structures. The discerned outcomes revealed the substantial influence of CuPc concentration on key electrical parameters, with conspicuous trends noted in the values of n, ΦB, Rs/Rsh, and Nss. Furthermore, the observed increase in the reverse current as the illumination level increases highlights the potential utility of these SBDs as sensitive photodiodes/sensors/detectors.
- 12 May 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (14) , 1-20
Open AccessInvestigation of hybrid CuPc-doped ZnO/p-silicon photodiodes for photonic and electronic applications
Copper phthalocyanine (CuPc) doped zinc oxide (ZnO) interlayered Al/p-Si Schottky barrier diodes (SBDs) were systematically fabricated utilizing spin coating technique. This study was undertaken to meticulously assess the influence of varying concentrations of CuPc on the intricate electrical and photodiode characteristics of these devices. The investigation involved the characterization of the current–voltage (I–V) characteristics configured with distinct different doping concentrations of CuPc such as 0.05 wt%,1 wt%, 2 wt%, under a wide range of voltages (± 5 V) and illumination irradiances. These measurements enabled the calculation of various critical electrical variables, such as the ideality factor (n), barrier height (ΦB), series resistance (Rs), shunt resistance (Rsh), interface states density (Nss) and their response under various illumination levels (between 10 and 100 mW/cm2) and under dark condition. An increase in the reverse current as the illumination increases suggested the potential utility of these SBDs as photodiodes, photosensors, or photodetectors. Notably, the linear dynamic range (LDR), a crucial factor for image sensors which obtained around 14 for all photodiodes. The photodiodes exhibited a good rectification ratio (RR) of approximately 104. The results obtained indicate that the rectifying properties of the structures can be controlled by CuPc doping. In addition, the results indicated that the presence of CuPc significantly influenced the values of n, ΦB, Rs/Rsh, and Nss. To further analyze the devices, capacitance–voltage (C–V) and conductance–voltage (G–V) measurements were carried out to determine parameters such as diffusion potential (VD), dopant acceptor atoms concentration (NA), Fermi energy level (EF), and width of depletion layer (WD) at both 1 kHz and 1 MHz. The measurements revealed that the capacitance values were higher at low frequencies compared to high frequencies, and this behavior was attributed to Nss. In summary, this study suggests that the manufactured photodiodes have the potential to be employed as photodiodes, sensors, or detectors in optical sensing applications, and their performance can be tailored by adjusting the concentration of CuPc in the ZnO interlayered structures. The discerned outcomes revealed the substantial influence of CuPc concentration on key electrical parameters, with conspicuous trends noted in the values of n, ΦB, Rs/Rsh, and Nss. Furthermore, the observed increase in the reverse current as the illumination level increases highlights the potential utility of these SBDs as sensitive photodiodes/sensors/detectors.
- 6 October 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (11) , 115916
Hybrid photonic device based on Graphene Oxide (GO) doped P3HT-PCBM/p-Silicon for photonic applications
Graphene oxide (GO) doped poly(3-hexylthiophene):[6,6]-phenyl C61 butyric acid methyl ester (P3HT:PCBM) interlayered Al/p-Si Schottky barrier diodes (SBDs) were manufactured by spin coating technique and investigated for the effects of GO concentration on electrical and photodiode parameters. The current–voltage (I-V), measurements for the different mass ratios of GO:P3HT:PCBM (0:1:1(S1), 0.5:1:1(S2) and 2:1:1(S3)) used diodes allowed the determination of key electrical parameters, including ideality factor (n), barrier height (Φ B ), series resistance (R s ), shunt resistance (R sh ), interface states density (N ss ) and optical sensing behaviors in dark and different illumination levels (10, 30, 60, 80 and 100 mW cm−2). The rectification ratio (RR) was found to be in the order of 104. The trends obtained for the n, Φ B , R s /R sh and N ss show that these are influenced by the contribution of the GO. Observed increasing behavior of reverse current with increasing illumination shows that this SBDs can be use as photo-diodes/sensors/detectors. On the other hand, it was observed that the linear dynamic range (LDR), which is important parameter for image sensors, increased (6.86, 16.95 and 26.98 for S1, S2 and S3, respectively) with increasing GO contribution. In addition, to investigate and compare in more detail, capacitance–voltage (C-V) and conductance-voltage (G-V) measurements used for the determination of diffusion potential (V D ), concentration of dopant acceptor atoms (N A ), Fermi energy level (E F ), depletion layer width (W D ) for low frequency (1 kHz) and high frequency (1 MHz). The measured capacitance values showed a high value at the low frequency in comparison with the high frequency. This behavior explained on the basis of N ss . The findings suggest that the prepared diodes has the potential to serve as a photo-diodes/sensors/detectors for optical sensing applications.
- 6 October 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (11) , 115916
Hybrid photonic device based on Graphene Oxide (GO) doped P3HT-PCBM/p-Silicon for photonic applications
Graphene oxide (GO) doped poly(3-hexylthiophene):[6,6]-phenyl C61 butyric acid methyl ester (P3HT:PCBM) interlayered Al/p-Si Schottky barrier diodes (SBDs) were manufactured by spin coating technique and investigated for the effects of GO concentration on electrical and photodiode parameters. The current–voltage (I-V), measurements for the different mass ratios of GO:P3HT:PCBM (0:1:1(S1), 0.5:1:1(S2) and 2:1:1(S3)) used diodes allowed the determination of key electrical parameters, including ideality factor (n), barrier height (Φ B ), series resistance (R s ), shunt resistance (R sh ), interface states density (N ss ) and optical sensing behaviors in dark and different illumination levels (10, 30, 60, 80 and 100 mW cm−2). The rectification ratio (RR) was found to be in the order of 104. The trends obtained for the n, Φ B , R s /R sh and N ss show that these are influenced by the contribution of the GO. Observed increasing behavior of reverse current with increasing illumination shows that this SBDs can be use as photo-diodes/sensors/detectors. On the other hand, it was observed that the linear dynamic range (LDR), which is important parameter for image sensors, increased (6.86, 16.95 and 26.98 for S1, S2 and S3, respectively) with increasing GO contribution. In addition, to investigate and compare in more detail, capacitance–voltage (C-V) and conductance-voltage (G-V) measurements used for the determination of diffusion potential (V D ), concentration of dopant acceptor atoms (N A ), Fermi energy level (E F ), depletion layer width (W D ) for low frequency (1 kHz) and high frequency (1 MHz). The measured capacitance values showed a high value at the low frequency in comparison with the high frequency. This behavior explained on the basis of N ss . The findings suggest that the prepared diodes has the potential to serve as a photo-diodes/sensors/detectors for optical sensing applications.
- Open Access
- 28 March 2023
- Published by Gazi University in Gazi University Journal of Science Part A: Engineering and Innovation
- Vol. 10 (1) , 53-61
A Study on the Wide Frequency Range Electrical Variables in the Al/Coumarin–PVA/p-Si Diodes at Room Temperature
Coumarin-PVA is deposited onto p-Si wafers using the spin coating technique. I examined the fundamental electrical variables of the Al/CoumarinPVA/p-Si type Schottky barrier diodes (SBDs), by utilizing capacitance/voltage(C-V) and conductance/voltage (G-V) measurements at different frequencies varied from 10kHz to1MHz. I have thoroughly explored how the CoumarinPVA interlayer, series resistance (Rs) and surface states (Nss) affect the electrical properties of SBDs. In order to remove Rs's influence on the observed C and G values, I corrected them. The observed high values of C/G measured at low frequencies result from the existence of interfacial states. There is evidence that while NA decreases exponentially with increasing frequency, B increases exponentially. A particular distribution of Nss density, polarization processes, and the existence of an interfacial layer can all contribute to explaining these characteristic features of them. According to experimental findings, I conclude that the interfacial polymer CoumarinPVA layer as well as the Nss and Rs also have a significant impact on the C/G-V quantities of SBDs.
- 28 March 2023
- Published by Gazi University in Gazi University Journal of Science Part A: Engineering and Innovation
- Vol. 10 (1) , 53-61
Open AccessA Study on the Wide Frequency Range Electrical Variables in the Al/Coumarin–PVA/p-Si Diodes at Room Temperature
Coumarin-PVA is deposited onto p-Si wafers using the spin coating technique. I examined the fundamental electrical variables of the Al/CoumarinPVA/p-Si type Schottky barrier diodes (SBDs), by utilizing capacitance/voltage(C-V) and conductance/voltage (G-V) measurements at different frequencies varied from 10kHz to1MHz. I have thoroughly explored how the CoumarinPVA interlayer, series resistance (Rs) and surface states (Nss) affect the electrical properties of SBDs. In order to remove Rs's influence on the observed C and G values, I corrected them. The observed high values of C/G measured at low frequencies result from the existence of interfacial states. There is evidence that while NA decreases exponentially with increasing frequency, B increases exponentially. A particular distribution of Nss density, polarization processes, and the existence of an interfacial layer can all contribute to explaining these characteristic features of them. According to experimental findings, I conclude that the interfacial polymer CoumarinPVA layer as well as the Nss and Rs also have a significant impact on the C/G-V quantities of SBDs.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (23) , 22391-22397
Vertical CdTe:PVP/p-Si-Based Temperature Sensor by Using Aluminum Anode Schottky Contact
The vertical Schottky barrier diode (SBD)-based temperature sensors with the drive modes are a significant issue with more advantageous than the on-chip sensor. The sensitivity ( ${S}$ ) and the current conduction mechanisms (CCMs) of the vertical cadmium telluride (CdTe):polyvinyl pyrolidone (PVP)/ ${p}$ -Si SBD were studied experimentally over the range of 80–340 K and compared with that of the lateral and vertical sensors. It is shown that the low and moderated voltages of the CdTe:PVP/ ${p}$ -Si corresponding two linear regions of the current–voltage ( ${I}$ – ${V}$ ) outputs are around 0.1–0.3 and 0.4–0.65 V, respectively. The variation of Schottky barrier height (BH; ${\sf \Phi } _{\text {Bo}}$ ) and ideality factor ( ${n}$ ) with temperature was obtained according to two linear regions. Energy dispersion of the interface traps ( ${N}_{\text {ss}}$ ) with changing temperature is additionally analyzed quantitatively. It is concluded that the thermionic-emission (TE) theory with double-Gaussian distribution (GD) is the dominant mechanism resulting the ${I}$ – ${V}$ characteristics of the vertical CdTe:PVP/ ${p}$ -Si SBD in this study. Moreover, in the constant current, the ${S}$ values at the drive current of 10, 20, and $50~\mu \text{A}$ were resulting in a range of −1.6 to −1.8 mV/K.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (23) , 22391-22397
Vertical CdTe:PVP/p-Si-Based Temperature Sensor by Using Aluminum Anode Schottky Contact
The vertical Schottky barrier diode (SBD)-based temperature sensors with the drive modes are a significant issue with more advantageous than the on-chip sensor. The sensitivity ( ${S}$ ) and the current conduction mechanisms (CCMs) of the vertical cadmium telluride (CdTe):polyvinyl pyrolidone (PVP)/ ${p}$ -Si SBD were studied experimentally over the range of 80–340 K and compared with that of the lateral and vertical sensors. It is shown that the low and moderated voltages of the CdTe:PVP/ ${p}$ -Si corresponding two linear regions of the current–voltage ( ${I}$ – ${V}$ ) outputs are around 0.1–0.3 and 0.4–0.65 V, respectively. The variation of Schottky barrier height (BH; ${\sf \Phi } _{\text {Bo}}$ ) and ideality factor ( ${n}$ ) with temperature was obtained according to two linear regions. Energy dispersion of the interface traps ( ${N}_{\text {ss}}$ ) with changing temperature is additionally analyzed quantitatively. It is concluded that the thermionic-emission (TE) theory with double-Gaussian distribution (GD) is the dominant mechanism resulting the ${I}$ – ${V}$ characteristics of the vertical CdTe:PVP/ ${p}$ -Si SBD in this study. Moreover, in the constant current, the ${S}$ values at the drive current of 10, 20, and $50~\mu \text{A}$ were resulting in a range of −1.6 to −1.8 mV/K.
- 18 August 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (26) , 21011-21021
Electrical characteristics and photosensing properties of Al/symmetrical CuPc/p-Si photodiodes
- 18 August 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (26) , 21011-21021
Electrical characteristics and photosensing properties of Al/symmetrical CuPc/p-Si photodiodes
- 14 April 2022
- Published by IOP Publishing in Physica Scripta
- Vol. 97 (5) , 055811
A comparison of Au/n-Si Schottky diodes (SDs) with/without a nanographite (NG) interfacial layer by considering interlayer, surface states (N ss ) and series resistance (R s ) effects
In this paper, an organic interlayer, R s , and N ss on the transport- mechanisms (TMs), both the Au/n-Si (MS) and Au/(Nanographite-PVP/n-Si (MPS) (SDs) were performed onto the same Si-wafer in same-conditions. Some electrical parameters of them have been investigated. The interface-traps/states ( D it /N ss ) were extracted from the I F – V F data as function of energy (E c –E ss ). These results show that the N ss for MPS is much-lower than MS SD and increase from the midgap-energy towards the E c like U-shape. Double-logarithmic I F – V F graphs of them show three linear-regimes for low, intermediate, and high-voltages and in these regimes, TM are governed by ohmic, trap/space charge limited currents (TCLCs/SCLCs), respectively. All these results show that (NG:PVP) interlayer leads to an increase in rectifier-ratio (RR = I F /I R ), BH, R sh , and decrease in N ss , reverse saturation-current ( I o ), and n. Thus, (NG:PVP) can be successfully utilized as interfacial layer with high performance characteristics.
- 14 April 2022
- Published by IOP Publishing in Physica Scripta
- Vol. 97 (5) , 055811
A comparison of Au/n-Si Schottky diodes (SDs) with/without a nanographite (NG) interfacial layer by considering interlayer, surface states (N ss ) and series resistance (R s ) effects
In this paper, an organic interlayer, R s , and N ss on the transport- mechanisms (TMs), both the Au/n-Si (MS) and Au/(Nanographite-PVP/n-Si (MPS) (SDs) were performed onto the same Si-wafer in same-conditions. Some electrical parameters of them have been investigated. The interface-traps/states ( D it /N ss ) were extracted from the I F – V F data as function of energy (E c –E ss ). These results show that the N ss for MPS is much-lower than MS SD and increase from the midgap-energy towards the E c like U-shape. Double-logarithmic I F – V F graphs of them show three linear-regimes for low, intermediate, and high-voltages and in these regimes, TM are governed by ohmic, trap/space charge limited currents (TCLCs/SCLCs), respectively. All these results show that (NG:PVP) interlayer leads to an increase in rectifier-ratio (RR = I F /I R ), BH, R sh , and decrease in N ss , reverse saturation-current ( I o ), and n. Thus, (NG:PVP) can be successfully utilized as interfacial layer with high performance characteristics.
- 10 January 2022
- Published by Springer Nature in Silicon
- Vol. 14 (14) , 8517-8527
Doping rate, Interface states and Polarization Effects on Dielectric Properties, Electric Modulus, and AC Conductivity in PCBM/NiO:ZnO/p-Si Structures in Wide Frequency Range
- 10 January 2022
- Published by Springer Nature in Silicon
- Vol. 14 (14) , 8517-8527
Doping rate, Interface states and Polarization Effects on Dielectric Properties, Electric Modulus, and AC Conductivity in PCBM/NiO:ZnO/p-Si Structures in Wide Frequency Range