Marc Fleury
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marc Fleury has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Thibaud Chevalier
IFP Energies nouvelles, 1 et 4 avenue de Bois-Préau, 92852 Rueil-Malmaison, France
4 shared publications A. Delbos
IFPEN, Rueil-malmaison, France
1 shared publication- Anne Sinquin
IFP Energies nouvelles, 1-4 avenue de Bois-Préau, 92852 Rueil-Malmaison, France
1 shared publication B. Bourbiaux
IFPEN, Rueil-malmaison, France
1 shared publication- Ben Norden
GFZ Helmholtz Centre for Geosciences, 14473 Potsdam, Germany
1 shared publication Benjamin Nicot
1 shared publication
Latest Publications
- Open Access
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
Study of aging mechanisms in lithium-ion batteries using NMR cryoporometry and laser-induced breakdown spectroscopy
Understanding aging mechanisms in Li-ion batteries is critical for optimizing lifetime and performance, yet remains challenging due to the complex interplay of chemical, thermal and mechanical processes across multiple scales. In this study, laser-induced breakdown spectroscopy (LIBS) and NMR cryoporometry were employed to investigate aging mechanisms under two conditions: low-temperature cycling (0 °C, 1C, 100-50% SOC) and high-temperature storage (60 °C, 4.2 V hold). Four commercial NMC811/graphite cells (M50LT) were tested per condition, with one cell periodically removed for post-mortem analysis. Electrodes morphology was examined by SEM, while LIBS, micro-LIBS and ICP provided chemical insights. Porosity, pore size and surface area were assessed through helium pycnometry, NMR cryoporometry and krypton BET respectively. Capacity losses of 3 % and 10 % were obtained after 102 days of aging on stored and cycled cells respectively. Incremental capacity (IC)/differential voltage (DV) and post-mortem analysis demonstrated that these losses were mainly due to SEI growth, lithium-plating (only under cycling), Mn dissolution from NMC electrodes, irreversible lithium trapping in graphite layer and unexpected lithium accumulation in copper current collectors. Analysis of dominant pore size evolution enabled the estimation of surface layer growth. For stored graphite electrodes, SEI growth was identified as the primary degradation mechanism, with an estimated thickness of 22 nm. For cycled graphite, the surface growth resulted from the combined formation of SEI and plated lithium layers, reaching an estimated thickness of ~36 nm.
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessStudy of aging mechanisms in lithium-ion batteries using NMR cryoporometry and laser-induced breakdown spectroscopy
Understanding aging mechanisms in Li-ion batteries is critical for optimizing lifetime and performance, yet remains challenging due to the complex interplay of chemical, thermal and mechanical processes across multiple scales. In this study, laser-induced breakdown spectroscopy (LIBS) and NMR cryoporometry were employed to investigate aging mechanisms under two conditions: low-temperature cycling (0 °C, 1C, 100-50% SOC) and high-temperature storage (60 °C, 4.2 V hold). Four commercial NMC811/graphite cells (M50LT) were tested per condition, with one cell periodically removed for post-mortem analysis. Electrodes morphology was examined by SEM, while LIBS, micro-LIBS and ICP provided chemical insights. Porosity, pore size and surface area were assessed through helium pycnometry, NMR cryoporometry and krypton BET respectively. Capacity losses of 3 % and 10 % were obtained after 102 days of aging on stored and cycled cells respectively. Incremental capacity (IC)/differential voltage (DV) and post-mortem analysis demonstrated that these losses were mainly due to SEI growth, lithium-plating (only under cycling), Mn dissolution from NMC electrodes, irreversible lithium trapping in graphite layer and unexpected lithium accumulation in copper current collectors. Analysis of dominant pore size evolution enabled the estimation of surface layer growth. For stored graphite electrodes, SEI growth was identified as the primary degradation mechanism, with an estimated thickness of 22 nm. For cycled graphite, the surface growth resulted from the combined formation of SEI and plated lithium layers, reaching an estimated thickness of ~36 nm.
- Open Access
- 1 August 2025
- Published by KEAI Publishing in Magnetic Resonance Letters
- Vol. 5 (3)
Cryoporometry for short T2 samples: A T1 filter method applied to battery electrode characterization
The pore size distribution is often an important parameter for transport processes in porous media. Cryoporometry experiments can provide such data in the meso and macropore size up to 1 μm providing the sample temperature is finely controlled. We use a Peltier based system inserted directly into the NMR probe to control the temperature within 0.05 °C and impose temperature ramps down to 0.002 °C/min, necessary to characterize the largest pore sizes. The pore size information in the macropore range cannot be obtained from gas adsorption techniques while mercury injection is questionable for the material considered here. For porous materials made of paramagnetic minerals such as lithium-iron phosphate (LiFePO4, LFP) or nickel-manganese-cobalt oxides (NMC) and saturated with octamethylcyclotetrasiloxane (OMCTS), the T2 relaxation times are very short such as protons from the liquid and frozen phases cannot be separated. Hence the usual cryoporometry experiment cannot be performed. Instead, we propose to use the T1 contrast to separate these phases. The method is studied in detail along with some temperature effects linked with the T1 variation of the bulk frozen OMCTS. We show an example on two cathode materials part of industrial battery product.
- 1 August 2025
- Published by KEAI Publishing in Magnetic Resonance Letters
- Vol. 5 (3)
Open AccessCryoporometry for short T2 samples: A T1 filter method applied to battery electrode characterization
The pore size distribution is often an important parameter for transport processes in porous media. Cryoporometry experiments can provide such data in the meso and macropore size up to 1 μm providing the sample temperature is finely controlled. We use a Peltier based system inserted directly into the NMR probe to control the temperature within 0.05 °C and impose temperature ramps down to 0.002 °C/min, necessary to characterize the largest pore sizes. The pore size information in the macropore range cannot be obtained from gas adsorption techniques while mercury injection is questionable for the material considered here. For porous materials made of paramagnetic minerals such as lithium-iron phosphate (LiFePO4, LFP) or nickel-manganese-cobalt oxides (NMC) and saturated with octamethylcyclotetrasiloxane (OMCTS), the T2 relaxation times are very short such as protons from the liquid and frozen phases cannot be separated. Hence the usual cryoporometry experiment cannot be performed. Instead, we propose to use the T1 contrast to separate these phases. The method is studied in detail along with some temperature effects linked with the T1 variation of the bulk frozen OMCTS. We show an example on two cathode materials part of industrial battery product.
- 11 November 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (22) , 22298-22306
CO2 Hydrate in Porous Media: A Quantitative NMR Method to Detect Formation, Dissociation, and Localization
- 11 November 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (22) , 22298-22306
CO2 Hydrate in Porous Media: A Quantitative NMR Method to Detect Formation, Dissociation, and Localization
- 30 March 2023
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 355
Probing diffusional exchange in mesoporous zeolite by NMR diffusion and relaxation methods
- 30 March 2023
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 355
Probing diffusional exchange in mesoporous zeolite by NMR diffusion and relaxation methods
- 1 June 2022
- Published by Cambridge University Press (CUP) in Clays and Clay Minerals
- Vol. 70 (3) , 417-437
Porewater Content, Pore Structure and Water Mobility in Clays and Shales from NMR Methods
Sub-surface clay samples are difficult to characterize using conventional methods so non-invasive Nuclear Magnetic Resonance (NMR) techniques were used to evaluate in a preserved state the pore structure, porosity, water mobility, and affinity of various clay systems. Within the CLAYWAT project launched by the NEA Clay Club, some of the most advanced NMR techniques were applied to samples from 11 clay-rich sedimentary formations (Boom Clay, Yper Clay (both Belgium); Callovo-Oxfordian shale, Upper Toarcian (both France); Opalinus Clay from two sites (Switzerland); Queenston Fm., Georgian Bay Fm., Blue Mountain Fm. (all Canada); Boda Clay (Hungary); and Wakkanai Fm. and Koetoi Fm. (Japan)). The degree of induration within this suite of samples varies substantially, resulting in a wide porosity range of 0.02–0.6. The key finding is the determination of pore-size distribution by NMR cryoporometry in the range of 2 nm–1 μm with the native fluid present in the pore space for most samples. The water volume in pore sizes of T2 distributions indicate that water was diffusing throughout the pore network during the magnetization lifetime, implying that T2 distributions cannot be considered as proxies for the pore-size distributions. For the set of samples considered, the T1/T2 varied between 1.7 and 4.6, implying variable surface affinity. Finally, for most samples, a pore-shape factor of ~2.4, intermediate between a sheet (1) and a cylinder (4), was deduced.
- 1 June 2022
- Published by Cambridge University Press (CUP) in Clays and Clay Minerals
- Vol. 70 (3) , 417-437
Porewater Content, Pore Structure and Water Mobility in Clays and Shales from NMR Methods
Sub-surface clay samples are difficult to characterize using conventional methods so non-invasive Nuclear Magnetic Resonance (NMR) techniques were used to evaluate in a preserved state the pore structure, porosity, water mobility, and affinity of various clay systems. Within the CLAYWAT project launched by the NEA Clay Club, some of the most advanced NMR techniques were applied to samples from 11 clay-rich sedimentary formations (Boom Clay, Yper Clay (both Belgium); Callovo-Oxfordian shale, Upper Toarcian (both France); Opalinus Clay from two sites (Switzerland); Queenston Fm., Georgian Bay Fm., Blue Mountain Fm. (all Canada); Boda Clay (Hungary); and Wakkanai Fm. and Koetoi Fm. (Japan)). The degree of induration within this suite of samples varies substantially, resulting in a wide porosity range of 0.02–0.6. The key finding is the determination of pore-size distribution by NMR cryoporometry in the range of 2 nm–1 μm with the native fluid present in the pore space for most samples. The water volume in pore sizes of T2 distributions indicate that water was diffusing throughout the pore network during the magnetization lifetime, implying that T2 distributions cannot be considered as proxies for the pore-size distributions. For the set of samples considered, the T1/T2 varied between 1.7 and 4.6, implying variable surface affinity. Finally, for most samples, a pore-shape factor of ~2.4, intermediate between a sheet (1) and a cylinder (4), was deduced.
- Open Access
- 29 March 2019
- Published by EDP Sciences
- Vol. 89, 04004
A novel experimental approach for studying spontaneous imbibition processes with alkaline solutions
Spontaneous imbibition processes can play an important role in oil production. It can be enhanced or influenced by wettability changes generated by properly designed chemicals or by the natural surfactants resulting from reactive crude oils in the presence of alkaline solutions. The reaction of basic salts with some components of oil can, indeed, lead to the formation of natural soaps that reduces the interfacial tension between oil and brine. The latter scenario is studied herein on samples and oil from the St Ulrich oil field in the Vienna basin. To that end, spontaneous imbibition experiments were performed with two brines differing by the absence or presence of alkali. We first present a general novel technique to monitor saturation changes on small rock samples for the purpose of assessing the efficiency of a given recovery process. Samples of only 15 mm in diameter and 20 mm in length and set at irreducible saturation were fully immersed in the solution of interest, and the evolution of the samples’ saturation with time was monitored thanks to a dedicated NMR technique involving the quantification of the sole oil phase present within the sample. A fully-3D imbibition configuration was adopted, involving counter-current flows through all faces of the sample. The experimental method is fast for two reasons: (i) the kinetics of capillary imbibition process is proportional to the square of sample size, i.e. very rapid if accurate measurements can be acquired on tiny samples, (ii) the present 3D situation also involves faster kinetics than the 1D configuration often used. The NMR technique was crucial to achieve such conditions that cannot be satisfied with conventional volumetric methods. The kinetics of oil desaturation during spontaneous imbibition is interpreted with the help of an analytical 3D diffusion model. For the alkaline solution, the diffusion coefficient is reduced by a factor of only two compared to the non-alkaline brine, although the interfacial tension between the oil and the imbibing solution is reduced by a factor of 10. Hence, a wettability change to a more water wet state has to be assumed when the alkaline solution replaces the non-alkaline solution in the imbibition process. However, no significant impact on the final saturation was observed.
- 29 March 2019
- Published by EDP Sciences
- Vol. 89, 04004
Open AccessA novel experimental approach for studying spontaneous imbibition processes with alkaline solutions
Spontaneous imbibition processes can play an important role in oil production. It can be enhanced or influenced by wettability changes generated by properly designed chemicals or by the natural surfactants resulting from reactive crude oils in the presence of alkaline solutions. The reaction of basic salts with some components of oil can, indeed, lead to the formation of natural soaps that reduces the interfacial tension between oil and brine. The latter scenario is studied herein on samples and oil from the St Ulrich oil field in the Vienna basin. To that end, spontaneous imbibition experiments were performed with two brines differing by the absence or presence of alkali. We first present a general novel technique to monitor saturation changes on small rock samples for the purpose of assessing the efficiency of a given recovery process. Samples of only 15 mm in diameter and 20 mm in length and set at irreducible saturation were fully immersed in the solution of interest, and the evolution of the samples’ saturation with time was monitored thanks to a dedicated NMR technique involving the quantification of the sole oil phase present within the sample. A fully-3D imbibition configuration was adopted, involving counter-current flows through all faces of the sample. The experimental method is fast for two reasons: (i) the kinetics of capillary imbibition process is proportional to the square of sample size, i.e. very rapid if accurate measurements can be acquired on tiny samples, (ii) the present 3D situation also involves faster kinetics than the 1D configuration often used. The NMR technique was crucial to achieve such conditions that cannot be satisfied with conventional volumetric methods. The kinetics of oil desaturation during spontaneous imbibition is interpreted with the help of an analytical 3D diffusion model. For the alkaline solution, the diffusion coefficient is reduced by a factor of only two compared to the non-alkaline brine, although the interfacial tension between the oil and the imbibing solution is reduced by a factor of 10. Hence, a wettability change to a more water wet state has to be assumed when the alkaline solution replaces the non-alkaline solution in the imbibition process. However, no significant impact on the final saturation was observed.
- 1 February 2019
- Published by Elsevier in Magnetic Resonance Imaging
- Vol. 56, 32-36
Diffusion of water in industrial cement and concrete
- 1 February 2019
- Published by Elsevier in Magnetic Resonance Imaging
- Vol. 56, 32-36
Diffusion of water in industrial cement and concrete
- Open Access
- 1 July 2017
- Published by Elsevier in Energy Procedia
- Vol. 114, 4172-4187
A Silicate Based Process for Plugging the Near Well Bore Formation
- 1 July 2017
- Published by Elsevier in Energy Procedia
- Vol. 114, 4172-4187
Open AccessA Silicate Based Process for Plugging the Near Well Bore Formation
- 1 March 2015
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 205, 75-78
Modeling of super-dispersion in unsaturated porous media using NMR propagators
- 1 March 2015
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 205, 75-78
Modeling of super-dispersion in unsaturated porous media using NMR propagators
- 18 June 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 1644-1653
Experimental Characterization of Chemical Alteration Effects on Carbonate Rock Dynamic Poroelastic Properties
This paper proposed an integrated experimental approach to the characterization of CO2 injection chemical impact on rock dynamic poroelastic properties. Acoustic measurements have been performed on intact and homogenously altered carbonate samples. The obtained results show a decrease of both the drained bulk modulus and the shear modulus under the effect of alteration. NMR measurements and microscanner imaging performed before and after alteration have provided an insight into the alteration impacts at the microscopic scale.
- 18 June 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 1644-1653
Experimental Characterization of Chemical Alteration Effects on Carbonate Rock Dynamic Poroelastic Properties
This paper proposed an integrated experimental approach to the characterization of CO2 injection chemical impact on rock dynamic poroelastic properties. Acoustic measurements have been performed on intact and homogenously altered carbonate samples. The obtained results show a decrease of both the drained bulk modulus and the shear modulus under the effect of alteration. NMR measurements and microscanner imaging performed before and after alteration have provided an insight into the alteration impacts at the microscopic scale.