Iman Rashidi
Iman Rashidi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Giulio Lorenzini
Department of Industrial Engineering, University of Parma, Parco Area delle Scienze, 181/A, Parma 43124, Italy
2 shared publications- Omid Mahian
School of Chemical Engineering and Technology, Xi’an Jiaotong University, Xi’an, China
2 shared publications Somchai Wongwises
Fluid Mechanics, Thermal Engineering and Multiphase Flow Research Laboratory (FUTURE), Department of Mechanical Engineering, Faculty of Engineering, King Mongkut's University of Technology Thonburi, Bangmod, Bangkok 10140, Thailand
2 shared publications- Abiodun O. Ajibade
Department of Mathematics Ahmadu Bello University Zaria Nigeria
1 shared publication - Cesare Biserni
University of Bologna
1 shared publication E. Abu-Nada
Khalifa University of Science and Technology, Abu Dhabi, United Arab Emirates
1 shared publication
Latest Publications
- Open Access
- 1 January 2021
- Published by Taylor & Francis in Journal of Taibah University for Science
- Vol. 15 (1) , 1013-1026
Second law analysis of magnetized Casson nanofluid flow in squeezing geometry with porous medium and thermophysical influence
This flow investigation analysed the entropy generation rate as an additional enrichment to the rate of heat transfer in Casson nanofluid flow between squeezing disks. The flow is modelled mathematically in PDEs systems, transformed into systems of ODEs via a well-posed transformation, and then solved. In a limiting case, good agreement of the numerical results is achieved. The assumption of variable fluid properties was seen to downsize the fluid velocity and temperature fields but enriches the nanoparticle volume fraction. Entropy number remarkably minimized for thermophysical properties, yield stress, and squeezing impact, while nanoparticle parameters, thermal diffusivity, and viscous dissipation contributed significantly to the system disorderliness. Moreover, findings reveal that thermal irreversibility controls the flow system in the entire channel (approximately ) except near the fixed disk where the other irreversibility dominated. Prandtl, Eckert, and Darcy's number help facilitate the irreversibility distribution phenomenon. With nanoscale mechanism modification nanoparticle volume fraction and energy distributions can easily be achieved.- 1 January 2021
- Published by Taylor & Francis in Journal of Taibah University for Science
- Vol. 15 (1) , 1013-1026
Open AccessSecond law analysis of magnetized Casson nanofluid flow in squeezing geometry with porous medium and thermophysical influence
This flow investigation analysed the entropy generation rate as an additional enrichment to the rate of heat transfer in Casson nanofluid flow between squeezing disks. The flow is modelled mathematically in PDEs systems, transformed into systems of ODEs via a well-posed transformation, and then solved. In a limiting case, good agreement of the numerical results is achieved. The assumption of variable fluid properties was seen to downsize the fluid velocity and temperature fields but enriches the nanoparticle volume fraction. Entropy number remarkably minimized for thermophysical properties, yield stress, and squeezing impact, while nanoparticle parameters, thermal diffusivity, and viscous dissipation contributed significantly to the system disorderliness. Moreover, findings reveal that thermal irreversibility controls the flow system in the entire channel (approximately ) except near the fixed disk where the other irreversibility dominated. Prandtl, Eckert, and Darcy's number help facilitate the irreversibility distribution phenomenon. With nanoscale mechanism modification nanoparticle volume fraction and energy distributions can easily be achieved. - 15 August 2019
- Published by Emerald Publishing in International Journal of Numerical Methods for Heat & Fluid Flow
- Vol. 30 (1) , 119-142
Three-dimensional modelling of natural convection and entropy generation in a vertical cylinder under heterogeneous heat flux using nanofluids
Purpose: This study aims to investigate a three-dimensional computational modelling of free convection of Al2O3 water-based nanofluid in a cylindrical cavity under heterogeneous heat fluxes that can be used as a thermal storage tank. Design/methodology/approach: Effects of different heat flux boundary conditions on heat transfer and entropy generation were examined and the optimal configuration was identified. The simulation results for nanoparticle (NP) volume fractions up to 4 per cent, and Rayleigh numbers of 104, 105 and 106 were presented. Findings: The results showed that for low Ra (104) the heat transfer and entropy generation patterns were symmetric, whereas with increasing the Rayleigh number these patterns became asymmetric and more complex. Therefore, despite the symmetric boundary conditions imposed on the periphery of the enclosure (uniform in Ɵ), it was necessary to simulate the problem as three-dimensional instead of two-dimensional. The simulation results showed that by selecting the optimal values of heat flux distribution and NP volume fraction for these systems the energy consumption can be reduced, and consequently, the energy efficiency can be ameliorated. Originality/value: The results of the present study can be used for the design of energy devices such as thermal storage tanks, as both first and second laws of thermodynamics have been considered. Using the optimal design will reduce energy consumption.
- 15 August 2019
- Published by Emerald Publishing in International Journal of Numerical Methods for Heat & Fluid Flow
- Vol. 30 (1) , 119-142
Three-dimensional modelling of natural convection and entropy generation in a vertical cylinder under heterogeneous heat flux using nanofluids
Purpose: This study aims to investigate a three-dimensional computational modelling of free convection of Al2O3 water-based nanofluid in a cylindrical cavity under heterogeneous heat fluxes that can be used as a thermal storage tank. Design/methodology/approach: Effects of different heat flux boundary conditions on heat transfer and entropy generation were examined and the optimal configuration was identified. The simulation results for nanoparticle (NP) volume fractions up to 4 per cent, and Rayleigh numbers of 104, 105 and 106 were presented. Findings: The results showed that for low Ra (104) the heat transfer and entropy generation patterns were symmetric, whereas with increasing the Rayleigh number these patterns became asymmetric and more complex. Therefore, despite the symmetric boundary conditions imposed on the periphery of the enclosure (uniform in Ɵ), it was necessary to simulate the problem as three-dimensional instead of two-dimensional. The simulation results showed that by selecting the optimal values of heat flux distribution and NP volume fraction for these systems the energy consumption can be reduced, and consequently, the energy efficiency can be ameliorated. Originality/value: The results of the present study can be used for the design of energy devices such as thermal storage tanks, as both first and second laws of thermodynamics have been considered. Using the optimal design will reduce energy consumption.
- 20 September 2016
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 9 (1) , 011003
Exergy Optimization of a Double-Exposure Solar Cooker by Response Surface Method
The purpose of this study was to optimize the performance of a double-exposure solar cooker based on exergy efficiency. Two similar solar cookers with variable parabolic mirror position were used for this experimental research. The system's exergy depends on many variables, which were kept fixed with the exception of the mirror position and operation time. The mathematical model of exergy efficiency was obtained based on the experimental variables, which could be used to optimize the mirror positions at any time. As a result, a new system with a variable mirror on a parabolic curve was developed, which can yield up to 30% increased mean exergy efficiency. Validation of the results was carried out by both the variance analysis test and comparing with the experimental data. The experiments were carried out in Mashhad, Iran, at 37 latitude, 54 longitude, and a height of 985 m above sea level.
- 20 September 2016
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 9 (1) , 011003
Exergy Optimization of a Double-Exposure Solar Cooker by Response Surface Method
The purpose of this study was to optimize the performance of a double-exposure solar cooker based on exergy efficiency. Two similar solar cookers with variable parabolic mirror position were used for this experimental research. The system's exergy depends on many variables, which were kept fixed with the exception of the mirror position and operation time. The mathematical model of exergy efficiency was obtained based on the experimental variables, which could be used to optimize the mirror positions at any time. As a result, a new system with a variable mirror on a parabolic curve was developed, which can yield up to 30% increased mean exergy efficiency. Validation of the results was carried out by both the variance analysis test and comparing with the experimental data. The experiments were carried out in Mashhad, Iran, at 37 latitude, 54 longitude, and a height of 985 m above sea level.
- 1 July 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 74, 391-402
Natural convection of Al2O3/water nanofluid in a square cavity: Effects of heterogeneous heating
- 1 July 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 74, 391-402
Natural convection of Al2O3/water nanofluid in a square cavity: Effects of heterogeneous heating
- 21 December 2012
- Published by ASME International in Journal of Fluids Engineering
- Vol. 135 (1) , 011301
The Optimum Design of a Cavitator for High-Speed Axisymmetric Bodies in Partially Cavitating Flows
In this paper, the partially cavitating flow over an axisymmetric projectile is studied in order to obtain the optimum cavitator such that, at a given cavitation number, the total drag coefficient of the projectile is minimum. For this purpose, the boundary element method and numerical simulations are used. A large number of cavitator profiles are produced using a parabolic expression with three geometric parameters. The potential flow around these cavitators is then solved using the boundary element method. In order to examine the optimization results, several cavitators with a total drag coefficient close to that of the optimum cavitators are also numerically simulated. Eventually, the optimum cavitator is selected using both the boundary element method and numerical simulations. The effects of the body radius and the length of the conical section of the projectile on the shape of the optimized cavitator are also investigated. The results show that for all cavitation numbers, the cavitator that creates a cavity covering the entire conical section of the projectile with a minimum total drag coefficient is optimal. It can be seen that increasing the cavitation number causes the optimum cavitator to approach the disk cavitator. The results also show that at a fixed cavitation number, the increase in both the radius and length of the conical section causes the cavitator shape to approach that of the disk cavitator.
- 21 December 2012
- Published by ASME International in Journal of Fluids Engineering
- Vol. 135 (1) , 011301
The Optimum Design of a Cavitator for High-Speed Axisymmetric Bodies in Partially Cavitating Flows
In this paper, the partially cavitating flow over an axisymmetric projectile is studied in order to obtain the optimum cavitator such that, at a given cavitation number, the total drag coefficient of the projectile is minimum. For this purpose, the boundary element method and numerical simulations are used. A large number of cavitator profiles are produced using a parabolic expression with three geometric parameters. The potential flow around these cavitators is then solved using the boundary element method. In order to examine the optimization results, several cavitators with a total drag coefficient close to that of the optimum cavitators are also numerically simulated. Eventually, the optimum cavitator is selected using both the boundary element method and numerical simulations. The effects of the body radius and the length of the conical section of the projectile on the shape of the optimized cavitator are also investigated. The results show that for all cavitation numbers, the cavitator that creates a cavity covering the entire conical section of the projectile with a minimum total drag coefficient is optimal. It can be seen that increasing the cavitation number causes the optimum cavitator to approach the disk cavitator. The results also show that at a fixed cavitation number, the increase in both the radius and length of the conical section causes the cavitator shape to approach that of the disk cavitator.