Tomio Okawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tomio Okawa has a total of 144 co-authors. Here are the top co-authors by number of shared publications:
Isao Kataoka
Osaka University, Department of Mechanical Engineering, 2-1, Yamadaoka, Suita-shi Osaka 565-0871, Japan
23 shared publications- Koji Enoki
Yo Ishigaki is a director and professor at the Research Center for Realizing Sustainable Societies, University of Electro-communications, Chofu, Tokyo, Japan and can be reached at [ protected]
18 shared publications Michitsugu Mori
Tokyo Electric Power Company , Tsurumi-ku, Yokohama-shi, Kanagawa, Japan
8 shared publicationsMitsuhiro Aoyagi
7 shared publicationsYi Zhan
7 shared publicationsAkio Kotani
Osaka University, Department of Mechanical Engineering, 2-1, Yamadaoka, Suita-shi Osaka 565-0871, Japan
5 shared publications
Latest Publications
- 27 March 2026
- Published by Taylor & Francis in Nuclear Technology
- p. 1-12
Interpreting Thermally and Hydrodynamically Controlled Regions in Subcooled Flow Boiling
- 27 March 2026
- Published by Taylor & Francis in Nuclear Technology
- p. 1-12
Interpreting Thermally and Hydrodynamically Controlled Regions in Subcooled Flow Boiling
- 1 April 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 247
Interference effect of nearby nucleation sites on bubble release frequency in subcooled flow boiling
- 1 April 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 247
Interference effect of nearby nucleation sites on bubble release frequency in subcooled flow boiling
- 28 November 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 220
Experiments on the onset of boiling entrainment from a falling liquid film with gas sheared flow
- 28 November 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 220
Experiments on the onset of boiling entrainment from a falling liquid film with gas sheared flow
- 3 November 2023
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 151
Effects of nozzle orifice shape on jet breakup and splashing during liquid jet impact onto a horizontal plate
- 3 November 2023
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 151
Effects of nozzle orifice shape on jet breakup and splashing during liquid jet impact onto a horizontal plate
- Open Access
- 18 September 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 195
Semi-mechanistic prediction of DNB heat flux based on global bubble coalescence concept
- 18 September 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 195
Open AccessSemi-mechanistic prediction of DNB heat flux based on global bubble coalescence concept
- 17 July 2023
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 9 (4) , 1-11
A Simple Analytical Model to Predict the Freeze Plug Opening Time in Molten Salt Reactors
The Freeze plug is an important passive safety system used in molten salt reactor (MSR). It enables automatic drainage of the liquid fuel from the core to the storage tanks in an emergency to stop the nuclear fission chain reaction without any operator's action or electric power supply. The opening time, that is the time taken for the freeze plug to open, is therefore of considerable importance to ensure passive safety of MSR. In our previous studies, systematic numerical simulations were carried out to understand how the fundamental design parameters such as the tube diameter and wall thickness of the freeze plug affected the opening time. In this work, a simple analytical model was developed for rough estimation of the opening time. It was shown that the opening time calculated by the present simple model was in fairly good agreement with that by the full simulation using the mass, momentum, and energy conservation equations for the salt and the heat conduction equation within the wall material. The present simple model was hence shown to be useful particularly for the schematic design of the improved MSR freeze plugs.
- 17 July 2023
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 9 (4) , 1-11
A Simple Analytical Model to Predict the Freeze Plug Opening Time in Molten Salt Reactors
The Freeze plug is an important passive safety system used in molten salt reactor (MSR). It enables automatic drainage of the liquid fuel from the core to the storage tanks in an emergency to stop the nuclear fission chain reaction without any operator's action or electric power supply. The opening time, that is the time taken for the freeze plug to open, is therefore of considerable importance to ensure passive safety of MSR. In our previous studies, systematic numerical simulations were carried out to understand how the fundamental design parameters such as the tube diameter and wall thickness of the freeze plug affected the opening time. In this work, a simple analytical model was developed for rough estimation of the opening time. It was shown that the opening time calculated by the present simple model was in fairly good agreement with that by the full simulation using the mass, momentum, and energy conservation equations for the salt and the heat conduction equation within the wall material. The present simple model was hence shown to be useful particularly for the schematic design of the improved MSR freeze plugs.
- 5 April 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 228
Experiments on thermal performance of heat pipes using nanoparticle layer as the wick
- 5 April 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 228
Experiments on thermal performance of heat pipes using nanoparticle layer as the wick