Eiji Shamoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eiji Shamoto has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Norikazu Suzuki
Department of Mechanical Aerospace Engineering, Nagoya University, Nagoya, Japan
18 shared publications - Rei Hino
Kobe University
11 shared publications Toshimichi Moriwaki
7 shared publicationsDaisuke Uekawa
2 shared publicationsHideki Yoshida
2 shared publicationsMasanori Morikawa
2 shared publications
Latest Publications
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Nanomanufacturing
- Vol. 13 (4) , 351
Influence of clearance angle on micro/nano structure fabrication in elliptical vibration cutting of hardened steel
International publishers of academic, scientific and professional journals since 1979.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Nanomanufacturing
- Vol. 13 (4) , 351
Influence of clearance angle on micro/nano structure fabrication in elliptical vibration cutting of hardened steel
International publishers of academic, scientific and professional journals since 1979.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Proceedings of International Conference on Leading Edge Manufacturing in 21st century : LEM21
- Vol. 2017.9, 066
Simulation-based Concurrent Identification of Milling Process and Mechanical Dynamics with Sensor-integrated Multi-inertial System Disturbance Observer
Identification method of cutting process is developed with sensor-integrated disturbance observer for general machine tools with multi-inertial feed drive systems. An acceleration sensor is adopted to the developed disturbance observer to eliminate high frequency noise in estimated disturbance force. The developed disturbance observer is also featured that the acceleration signal is processed based on mode decoupling approach. Through a milling test of carbon steel, experimental results verified higher performance of the observer with respect to the conventional observer without sensor integration. By utilizing the developed observer, concurrent identification of milling process and mechanical dynamics is attained successfully.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Proceedings of International Conference on Leading Edge Manufacturing in 21st century : LEM21
- Vol. 2017.9, 066
Simulation-based Concurrent Identification of Milling Process and Mechanical Dynamics with Sensor-integrated Multi-inertial System Disturbance Observer
Identification method of cutting process is developed with sensor-integrated disturbance observer for general machine tools with multi-inertial feed drive systems. An acceleration sensor is adopted to the developed disturbance observer to eliminate high frequency noise in estimated disturbance force. The developed disturbance observer is also featured that the acceleration signal is processed based on mode decoupling approach. Through a milling test of carbon steel, experimental results verified higher performance of the observer with respect to the conventional observer without sensor integration. By utilizing the developed observer, concurrent identification of milling process and mechanical dynamics is attained successfully.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of The Manufacturing & Machine Tool Conference
- Vol. 2016.11, D21
Development of a milling cutter with SPRT for difficult-to-cut materials machining
In order to improve milling performance of difficult-to-cut materials, a unique milling cutter with SPRT (Self-Propelled-Rotary-Tool) was developed. Use of slide bearings enables a compact SPRT mechanism, while influence of bearing friction becomes not negligible. To attain self-revolution of a circular insert regardless of the bearing friction, the cutter geometry was optimized. Through face milling experiments of Inconel 718, superior tool wear resistance was verified as compared to the conventional milling without insert rotation. Analytical result of the measured cutting forces also indicated interesting phenomena in SPRT milling.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of The Manufacturing & Machine Tool Conference
- Vol. 2016.11, D21
Development of a milling cutter with SPRT for difficult-to-cut materials machining
In order to improve milling performance of difficult-to-cut materials, a unique milling cutter with SPRT (Self-Propelled-Rotary-Tool) was developed. Use of slide bearings enables a compact SPRT mechanism, while influence of bearing friction becomes not negligible. To attain self-revolution of a circular insert regardless of the bearing friction, the cutter geometry was optimized. Through face milling experiments of Inconel 718, superior tool wear resistance was verified as compared to the conventional milling without insert rotation. Analytical result of the measured cutting forces also indicated interesting phenomena in SPRT milling.
- 15 April 2014
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 53 (5) , 05GB01
Primary study on nonlinear viscoelasticity measurement of chemical mechanical polishing pads by applying on-machine compression test
- 15 April 2014
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 53 (5) , 05GB01
Primary study on nonlinear viscoelasticity measurement of chemical mechanical polishing pads by applying on-machine compression test
- 1 January 2014
- Published by Springer Nature
- p. 1289-1294
Vibration
- 17 July 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (4) , 041001
Analysis of Three-Dimensional Cutting Process With Thin Shear Plane Model
A new and basic analytical model of three-dimensional cutting is proposed by assuming multiple thin shear planes with either the maximum shear stress or minimum energy principle. The three-dimensional cutting process with an arbitrarily shaped cutting edge in a flat rake face is formulated with simple vector equations in order to understand and quickly simulate the process. The cutting edge and workpiece profile are discretized and expressed by their position vectors. Two equations among three unknown vectors, which show the directions of shear, chip flow, and resultant cutting force, are derived from the geometric relations of velocities and forces. The last vector equation required to solve the three unknown vectors is obtained by applying either the maximum shear stress or minimum energy principle. It is confirmed that the directions and the cutting forces simulated by solving the proposed vector equations agree with experimentally measured data. Furthermore, the developed model is applied to consider the three-dimensional cutting mechanics, i.e., how the chip is formed in the three-dimensional cutting with compressive stress acting between the discrete chips, as an example.
- 17 July 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (4) , 041001
Analysis of Three-Dimensional Cutting Process With Thin Shear Plane Model
A new and basic analytical model of three-dimensional cutting is proposed by assuming multiple thin shear planes with either the maximum shear stress or minimum energy principle. The three-dimensional cutting process with an arbitrarily shaped cutting edge in a flat rake face is formulated with simple vector equations in order to understand and quickly simulate the process. The cutting edge and workpiece profile are discretized and expressed by their position vectors. Two equations among three unknown vectors, which show the directions of shear, chip flow, and resultant cutting force, are derived from the geometric relations of velocities and forces. The last vector equation required to solve the three unknown vectors is obtained by applying either the maximum shear stress or minimum energy principle. It is confirmed that the directions and the cutting forces simulated by solving the proposed vector equations agree with experimentally measured data. Furthermore, the developed model is applied to consider the three-dimensional cutting mechanics, i.e., how the chip is formed in the three-dimensional cutting with compressive stress acting between the discrete chips, as an example.
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series B
- Vol. 78 (788) , 762-768
Development of Mass-Producible Rapid Mixer Based on Baker's Transformation
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series B
- Vol. 78 (788) , 762-768
Open AccessDevelopment of Mass-Producible Rapid Mixer Based on Baker's Transformation
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2011.60, _568-1_
568 Study on Cutting of Difficult-to-Cut Materials with Rotary Tools
Rotary cutting process is modeled and its cutting performances are discussed in the present study. Actively or passively driven rotary cutting can be equivalent to oblique cutting. Assuming bearing resistance is negligible, passively driven rotary cutting can be further simplified as orthogonal cutting. Rotary milling tool is developed and applied to face milling tests of Inconel 718. Comparing with the conventional milling, experimental results indicated the feasibility of higher performance machining of Inconel 718 by the rotary tool.
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2011.60, _568-1_
568 Study on Cutting of Difficult-to-Cut Materials with Rotary Tools
Rotary cutting process is modeled and its cutting performances are discussed in the present study. Actively or passively driven rotary cutting can be equivalent to oblique cutting. Assuming bearing resistance is negligible, passively driven rotary cutting can be further simplified as orthogonal cutting. Rotary milling tool is developed and applied to face milling tests of Inconel 718. Comparing with the conventional milling, experimental results indicated the feasibility of higher performance machining of Inconel 718 by the rotary tool.
- 1 January 2011
- Published by Japan Society for Precision Engineering in Journal of the Japan Society for Precision Engineering
- Vol. 77 (1) , 97-104
Chatter Stability Limits in End Milling with Anisotropic Flexible Tools
- 1 January 2011
- Published by Japan Society for Precision Engineering in Journal of the Japan Society for Precision Engineering
- Vol. 77 (1) , 97-104
Chatter Stability Limits in End Milling with Anisotropic Flexible Tools