Olivera Popović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Olivera Popović has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandar Sedmak
University of Belgrade, Faculty of Mechanical Engineering, Belgrade, Serbia
5 shared publications - Radica Prokić Cvetković
Mašinski fakultet, Univerzitet u Beogradu, Kraljice Marije 16, 11000 Beograd, Srbija
4 shared publications - Marina Dojčinović
Faculty of Technology and Metallurgy, University of Belgrade, 11000 Belgrade, Serbia
3 shared publications - Ivana Cvetković
University of Belgrade — Faculty of Mechanical Engineering
2 shared publications - Marko Pavlović
Faculty of Mechanical Engineering, University of Belgrade - Innovation Center, Belgrade, Serbia
2 shared publications Radomir Jovičić
Univerzitet u Beogradu Inovacioni centar Mašinskog fakulteta Kraljice Marije 16 Beograd Srbija
2 shared publications
Latest Publications
- 30 December 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (3) , 393-398
Cavitation erosion - process and development of testing methods
The paper presents an ultrasonic vibration method for laboratory testing of the resistance of materials to the effect of cavitation. The description of the test method and device, the test procedure, and the interpretation of test results are given in accordance with ASTM G32 standard. A comparative overview of the test results of different types of materials is presented: metal (steel, aluminium alloys); ceramics (based on pure and mixed refractory fillers); composite materials with a polymer base; refractory castings and protective coatings. Based on the test results, the correlation of structural characteristics, mechanical properties of materials are determined as a basis for quick selection of materials in hydrodynamic conditions of application.
- 30 December 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (3) , 393-398
Cavitation erosion - process and development of testing methods
The paper presents an ultrasonic vibration method for laboratory testing of the resistance of materials to the effect of cavitation. The description of the test method and device, the test procedure, and the interpretation of test results are given in accordance with ASTM G32 standard. A comparative overview of the test results of different types of materials is presented: metal (steel, aluminium alloys); ceramics (based on pure and mixed refractory fillers); composite materials with a polymer base; refractory castings and protective coatings. Based on the test results, the correlation of structural characteristics, mechanical properties of materials are determined as a basis for quick selection of materials in hydrodynamic conditions of application.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 245-248
Influence of welding parameters on the geometric characteristics of surface weld metal obtained by handheld laser welding
The handheld laser welding process is the latest innovation in welding technology with an increasingly broad range of applications primarily due to the simplicity of the welder training, the minimal influence of the welder on joint quality, low heat input, high welding speed, and lower equipment costs. In this paper, the influence of selected welding parameters (wire feed rate and laser oscillation width) on the geometric characteristics of surface welds on low-carbon steel P235GH is presented. Additionally, based on the selected optimal parameters, a butt joint is performed by welding plates made of the same base material. The dependence of these parameters on weld metal width and weld metal reinforcement is determined. Furthermore, it is concluded that use of a higher power device would most likely be successful in a complete root penetration during butt welding.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 245-248
Influence of welding parameters on the geometric characteristics of surface weld metal obtained by handheld laser welding
The handheld laser welding process is the latest innovation in welding technology with an increasingly broad range of applications primarily due to the simplicity of the welder training, the minimal influence of the welder on joint quality, low heat input, high welding speed, and lower equipment costs. In this paper, the influence of selected welding parameters (wire feed rate and laser oscillation width) on the geometric characteristics of surface welds on low-carbon steel P235GH is presented. Additionally, based on the selected optimal parameters, a butt joint is performed by welding plates made of the same base material. The dependence of these parameters on weld metal width and weld metal reinforcement is determined. Furthermore, it is concluded that use of a higher power device would most likely be successful in a complete root penetration during butt welding.
- Open Access
- 15 April 2025
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 32 (2) , 683-691
Cracking of HSLA Steel Nioval 47 Caused by Exploitation Condition and Repair Welding
The metallurgical characteristics of high-strength low-alloyed (HSLA) steel and the effects that could lead to crack initiation, especially in the heat affected zone, have to be taken into account during defining welding technology. Primary aim of th...
- 15 April 2025
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 32 (2) , 683-691
Open AccessCracking of HSLA Steel Nioval 47 Caused by Exploitation Condition and Repair Welding
The metallurgical characteristics of high-strength low-alloyed (HSLA) steel and the effects that could lead to crack initiation, especially in the heat affected zone, have to be taken into account during defining welding technology. Primary aim of th...
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Science of Sintering
- Vol. 58 (00) , 30
Cavitation erosion of samples based on cordierite-talc ceramics
In the paper, the cavitation resistance of cordierite samples with the addition of 10%, 15% and 20% talc, sintered at 1200?C, was investigated. The ultrasonic vibration method with a stationary sample according to the ASTM G32 standard was applied. The formation and development of damage to the surface of the samples was monitored using a scanning electron microscope and the level of damage to the surface of the samples was quantified using image analysis. The change in the mass of the samples as a function of the cavitation time was monitored to determine the cavitation rate. By measuring the mass loss and morphological analysis of the pits formed on the surface of the sintered samples of the cordierite-talc ceramics, the mechanism of degradation and resistance to the effect of cavitation was monitored. The obtained results were compared with the results of earlier tests of cavitation resistance of sintered cordierite samples. The addition of talc in the mixture with cordierite significantly improved cavitation resistance of the sintered material compared to sintered pure cordierite. The tests were done to see the potential application of this material in hydrodynamic conditions, especially because of the strong corrosion resistance of these refractory materials.
- 1 January 2024
- Published by National Library of Serbia in Science of Sintering
- Vol. 58 (00) , 30
Open AccessCavitation erosion of samples based on cordierite-talc ceramics
In the paper, the cavitation resistance of cordierite samples with the addition of 10%, 15% and 20% talc, sintered at 1200?C, was investigated. The ultrasonic vibration method with a stationary sample according to the ASTM G32 standard was applied. The formation and development of damage to the surface of the samples was monitored using a scanning electron microscope and the level of damage to the surface of the samples was quantified using image analysis. The change in the mass of the samples as a function of the cavitation time was monitored to determine the cavitation rate. By measuring the mass loss and morphological analysis of the pits formed on the surface of the sintered samples of the cordierite-talc ceramics, the mechanism of degradation and resistance to the effect of cavitation was monitored. The obtained results were compared with the results of earlier tests of cavitation resistance of sintered cordierite samples. The addition of talc in the mixture with cordierite significantly improved cavitation resistance of the sintered material compared to sintered pure cordierite. The tests were done to see the potential application of this material in hydrodynamic conditions, especially because of the strong corrosion resistance of these refractory materials.
- Open Access
- 27 October 2023
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 29 (4) , 369-378
How to replace the original material for the welded structure manufacturing
Due to difficult pandemic situation with COVID-19 decease, as well as due to current geopolitical circumstances in the world, we are facing the shortage of steel and therefore the impossibility of delivering the contracted products within the agreed deadlines. It is thus necessary to find suitable steel for replacement. The procedure for selecting one such steel for substituting the deficit steel 25CrMo4, for the purposes of producing a responsible welded assembly, is described in this paper. After the careful analysis, the steel 42CrMo4 was taken into consideration as a possible substitute material. Prior to applying the new selected steel, it was necessary to perform the following tests: analyze its chemical composition, determine its most important mechanical properties and evaluate its weldability. Then, the optimal welding and heat treatment technologies were determined, so that the quality of the responsible welded structure would meet all the requirements, as the structure made of originally used steel. For the new steel, all the mentioned and some additional tests were conducted and the appropriate welding technology was prescribed. To verify the selected technology, appropriate tests were conducted on the model welded samples, the results of which are presented in this paper. Based on the analysis of the obtained results, it was concluded that the 25CrMo4 steel can be replaced by the 42CrMo4 steel, however, with the mandatory application of appropriate supplementary measures.
- 27 October 2023
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 29 (4) , 369-378
Open AccessHow to replace the original material for the welded structure manufacturing
Due to difficult pandemic situation with COVID-19 decease, as well as due to current geopolitical circumstances in the world, we are facing the shortage of steel and therefore the impossibility of delivering the contracted products within the agreed deadlines. It is thus necessary to find suitable steel for replacement. The procedure for selecting one such steel for substituting the deficit steel 25CrMo4, for the purposes of producing a responsible welded assembly, is described in this paper. After the careful analysis, the steel 42CrMo4 was taken into consideration as a possible substitute material. Prior to applying the new selected steel, it was necessary to perform the following tests: analyze its chemical composition, determine its most important mechanical properties and evaluate its weldability. Then, the optimal welding and heat treatment technologies were determined, so that the quality of the responsible welded structure would meet all the requirements, as the structure made of originally used steel. For the new steel, all the mentioned and some additional tests were conducted and the appropriate welding technology was prescribed. To verify the selected technology, appropriate tests were conducted on the model welded samples, the results of which are presented in this paper. Based on the analysis of the obtained results, it was concluded that the 25CrMo4 steel can be replaced by the 42CrMo4 steel, however, with the mandatory application of appropriate supplementary measures.
- Open Access
Effect of Shielding Gas Arc Welding Process on Cavitation Resistance of Welded Joints of AlMg4.5Mn Alloy
The effect of the shielding gas arc welding process on the cavitation resistance of the three-component aluminum alloy AlMg4.5Mn and its welded joints was investigated. Welding was performed using the GTAW and GMAW processes in a shielded atmosphere of pure argon. After the welding, metallographic tests were performed, and the hardness distribution in the welded joints was determined. The ultrasonic vibration method was used to evaluate the base metal’s and weld metal’s resistance to cavitation. The change in mass was monitored to determine the cavitation rates. The morphology of the surface damage of the base metal and weld metal due to cavitation was monitored using scanning electron microscopy to explain the effect of the shielding gas arc welding process on their resistance to cavitation.
Open AccessEffect of Shielding Gas Arc Welding Process on Cavitation Resistance of Welded Joints of AlMg4.5Mn Alloy
The effect of the shielding gas arc welding process on the cavitation resistance of the three-component aluminum alloy AlMg4.5Mn and its welded joints was investigated. Welding was performed using the GTAW and GMAW processes in a shielded atmosphere of pure argon. After the welding, metallographic tests were performed, and the hardness distribution in the welded joints was determined. The ultrasonic vibration method was used to evaluate the base metal’s and weld metal’s resistance to cavitation. The change in mass was monitored to determine the cavitation rates. The morphology of the surface damage of the base metal and weld metal due to cavitation was monitored using scanning electron microscopy to explain the effect of the shielding gas arc welding process on their resistance to cavitation.
- Open Access
- 13 January 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (2) , 1550
Fracture Behavior of AlMg4.5Mn Weld Metal at Different Temperatures under Impact Loading
This paper deals with a three-component aluminum alloy AlMg4.5Mn that was welded using a GTAW process in the shielded atmosphere of Ar+70%He+0.015%N2. The weld-metal toughness was evaluated at three different temperatures using instrumental Charpy pendulum impact testing to measure not only the total energy, but also the crack initiation energy and the crack growth energy. Fractographic analysis of the fracture surfaces and EDS analysis of large second-phase particles on fractured surfaces at each temperature were also carried out. Fractographic analysis at different temperatures indicated a clearly distinguishable fracture mechanism. It was inferred that the absorbed energy was closely correlated with the fracturing of surfaces. Moreover, it was concluded that with decrease in the amount of microscopic voids and dimples, the total energy absorbed also decreased.
- 13 January 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (2) , 1550
Open AccessFracture Behavior of AlMg4.5Mn Weld Metal at Different Temperatures under Impact Loading
This paper deals with a three-component aluminum alloy AlMg4.5Mn that was welded using a GTAW process in the shielded atmosphere of Ar+70%He+0.015%N2. The weld-metal toughness was evaluated at three different temperatures using instrumental Charpy pendulum impact testing to measure not only the total energy, but also the crack initiation energy and the crack growth energy. Fractographic analysis of the fracture surfaces and EDS analysis of large second-phase particles on fractured surfaces at each temperature were also carried out. Fractographic analysis at different temperatures indicated a clearly distinguishable fracture mechanism. It was inferred that the absorbed energy was closely correlated with the fracturing of surfaces. Moreover, it was concluded that with decrease in the amount of microscopic voids and dimples, the total energy absorbed also decreased.
- Open Access
- 1 January 2020
- Published by Singidunum University
- p. 181-187
Possibilities of the Application of ghe Software for Welding in Virtual Reality on the Welders Training
Welding in virtual reality is an artificial, computer generated, environment where the welder is located with a goal of the successful realization of the welding process
- 1 January 2020
- Published by Singidunum University
- p. 181-187
Open AccessPossibilities of the Application of ghe Software for Welding in Virtual Reality on the Welders Training
Welding in virtual reality is an artificial, computer generated, environment where the welder is located with a goal of the successful realization of the welding process
- Open Access
- 1 January 2018
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 63 (3) , 119-129
Welding of thick-walled steels in a narrow groove
Reduction in groove opening can significantly contribute to welding efficiency and productivity of heavy metal structures. It is common practice to use welded joint groove angles of 45° and 60°. Reduction of the groove opening angle decreases the necessary number of welding passes, thus decreasing the welding duration, filler material consumption and residual stresses and strain. However, groove angle reduction leads to certain difficulties. It is hard to control the arc in a narrow groove, which could lead to welded joint quality issues. In this paper, welding of butt joints made of 22 mm thick steel with the groove angle of 20° is shown. Welding was performed using the MAG procedure, with software controlled ar.
- 1 January 2018
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 63 (3) , 119-129
Open AccessWelding of thick-walled steels in a narrow groove
Reduction in groove opening can significantly contribute to welding efficiency and productivity of heavy metal structures. It is common practice to use welded joint groove angles of 45° and 60°. Reduction of the groove opening angle decreases the necessary number of welding passes, thus decreasing the welding duration, filler material consumption and residual stresses and strain. However, groove angle reduction leads to certain difficulties. It is hard to control the arc in a narrow groove, which could lead to welded joint quality issues. In this paper, welding of butt joints made of 22 mm thick steel with the groove angle of 20° is shown. Welding was performed using the MAG procedure, with software controlled ar.
- Open Access
- 1 January 2015
- Published by Singidunum University
- p. 760-762
Jezik struke: zavarivanje danas
U inženjerstvu, kao i u drugim oblastima nauke, veoma je važno precizno i jasno definisati određene pojmove
- 1 January 2015
- Published by Singidunum University
- p. 760-762
Open AccessJezik struke: zavarivanje danas
U inženjerstvu, kao i u drugim oblastima nauke, veoma je važno precizno i jasno definisati određene pojmove