Yi Wan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yi Wan has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Hongtao Ye
AVIC Shenyang Liming Aero-Engine Group Corporation Ltd, Shenyang, People’s Republic of China
1 shared publicationK Cheng
AMEE Department, School of Engineering and Design, Brunel University, Uxbridge, UK
1 shared publicationKai Cheng
AMEE Department, School of Engineering and Design, Brunel University, Uxbridge, UK
1 shared publicationXl Fu
Department of Mechanical Engineering, University of Jinan, Jinan, People’s Republic of China
1 shared publicationZhanqiang Liu
Key Laboratory of High Efficiency and Clean Manufacturing, School of Mechanical Engineering, Shandong University, Shandong, People’s Republic of China
1 shared publication- Zhanqiang Liu
School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication
Latest Publications
- 16 August 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (12) , 1916-1920
An investigation on machinability assessment of difficult-to-cut materials based on radar charts
A scientific understanding of all the factors affecting machinability and machining is essential for tool selection and process planning, particularly in Computer Numerical Control (CNC) machining of difficult-to-cut materials. This article proposed a radar chart–based method to assess material machinability by taking into account of multiple process variables quantitatively and to reveal comparison indexes visually. Key steps of this method included the reference material and indexes selection, normalization process and machinability assessment. Finally, a case study on using this method was given to assess three different types of titanium alloys. The order of machinability from good to poor is TC4, TC11 and TC17 supported with quantitative analysis.
- 16 August 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (12) , 1916-1920
An investigation on machinability assessment of difficult-to-cut materials based on radar charts
A scientific understanding of all the factors affecting machinability and machining is essential for tool selection and process planning, particularly in Computer Numerical Control (CNC) machining of difficult-to-cut materials. This article proposed a radar chart–based method to assess material machinability by taking into account of multiple process variables quantitatively and to reveal comparison indexes visually. Key steps of this method included the reference material and indexes selection, normalization process and machinability assessment. Finally, a case study on using this method was given to assess three different types of titanium alloys. The order of machinability from good to poor is TC4, TC11 and TC17 supported with quantitative analysis.
- 25 June 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 227 (11) , 1297-1305
An experiment-based investigation on surface corrosion resistance behaviors of aluminum alloy 7050-T7451 after end milling
High-strength aluminum alloys are widely used in the aeronautic industry because of their excellent combined performance including good corrosion resistance. In this paper, an experiment-based study on the surface characteristics is presented including residual stress and surface defects induced by end milling processes. Salt-spray corrosion tests are carried out on the end machined surfaces and corrosion morphologies during different corrosion periods are achieved. Observations from microscopy and energy dispersive X-ray spectrometer (EDS) analysis support the existence of micro-cracks, leading to occluded corrosion cells, which accelerate the corrosion. It is found that residual stress, micro-cracks and their combination are important to the corrosion resistance performance of machined aluminum alloy parts. Experiments show that while feed speed vf = 750 mm/min and rotational speed n = 4500 rpm, larger compressive stresses and lower corrosion depths are achieved.
- 25 June 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 227 (11) , 1297-1305
An experiment-based investigation on surface corrosion resistance behaviors of aluminum alloy 7050-T7451 after end milling
High-strength aluminum alloys are widely used in the aeronautic industry because of their excellent combined performance including good corrosion resistance. In this paper, an experiment-based study on the surface characteristics is presented including residual stress and surface defects induced by end milling processes. Salt-spray corrosion tests are carried out on the end machined surfaces and corrosion morphologies during different corrosion periods are achieved. Observations from microscopy and energy dispersive X-ray spectrometer (EDS) analysis support the existence of micro-cracks, leading to occluded corrosion cells, which accelerate the corrosion. It is found that residual stress, micro-cracks and their combination are important to the corrosion resistance performance of machined aluminum alloy parts. Experiments show that while feed speed vf = 750 mm/min and rotational speed n = 4500 rpm, larger compressive stresses and lower corrosion depths are achieved.