Diana Cotoros
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diana Cotoros has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Anca Stanciu
7 shared publications- Adina Elena Stanciu
Carcinogenesis and Molecular Biology Department, Institute of Oncology “Prof. Dr. Alexandru Trestioreanu”, 022328 Bucharest, Romania
4 shared publications - Ioan Serban
Department of Electrical Engineering and Applied Physics, Transilvania University of Brasov, Brasov, Romania
3 shared publications - Angela Repanovici
Faculty of Product Design and Environment, Transilvania University of Brasov, 500036 Brasov, Romania
2 shared publications Corneliu Druga
Product Design Mechatronics and Environment department, University Transilvania of Brasov Brasov Romania
2 shared publicationsCorneliu Drugă
University Transilvania of Braşov
2 shared publications
Latest Publications
- Open Access
- 1 May 2021
- Published by IACSIT Press in International Journal of Modeling and Optimization
- p. 53-57
Continuously Variable Transmission Vehicle Modeling and Control Algorithm Considering Fuel Efficiency and Driveline Efficiency
The device presented in this paper was designed in order to give a hand to the deaf-mute community, by helping them to reintegrate in the society, using the modern technologies. We aim at manufacturing an intelligent glove based on the use of sensors in order to obtain a communication bridge with a decent speech level between the persons suffering hearing loss and the persons with normal hearing. The development and design of the glove represents an endeavor that aims at obtaining pertinent data from fingers’ motion. The prototype functionality can be easily compared with gloves for virtual applications as they work on the same principle, namely sensory activity and test subjects will verify the concept objectives.
- 1 May 2021
- Published by IACSIT Press in International Journal of Modeling and Optimization
- p. 53-57
Open AccessContinuously Variable Transmission Vehicle Modeling and Control Algorithm Considering Fuel Efficiency and Driveline Efficiency
The device presented in this paper was designed in order to give a hand to the deaf-mute community, by helping them to reintegrate in the society, using the modern technologies. We aim at manufacturing an intelligent glove based on the use of sensors in order to obtain a communication bridge with a decent speech level between the persons suffering hearing loss and the persons with normal hearing. The development and design of the glove represents an endeavor that aims at obtaining pertinent data from fingers’ motion. The prototype functionality can be easily compared with gloves for virtual applications as they work on the same principle, namely sensory activity and test subjects will verify the concept objectives.
- 16 April 2021
- Published by Wiley in Macromolecular Symposia
- Vol. 396 (1) , 2000260
Analysis of the Thermal Behavior of Materials for Orthopedic Heels
The present paper proposes an experiment meant to determine the change of dimensions that may occur due to the increase of temperature of the orthopedic heels. The 3D model is manufactured using ethylene‐vinyl acetyl, also known as EVA, a copolymer made of ethylene and vinyl acetyl, which is very flexible and light weighted, also impermeable and UV and shock resistant. Five of the most used materials are analyzed during the experiment Orange Support, Blue Comfort, Multicolor, Green Relax, and Yellow Soft. Dimensions measurements are also taken five times a day for 5 days and recorded in tables and diagrams using Excel tools.In order to perform a statistical analysis of the results, the F‐Anova test is used and applied upon the recorded values. The conclusion is that there is a significant change of dimensions in the orthopedic heels materials that might affect the comfort of the users in certain conditions.
- 16 April 2021
- Published by Wiley in Macromolecular Symposia
- Vol. 396 (1) , 2000260
Analysis of the Thermal Behavior of Materials for Orthopedic Heels
The present paper proposes an experiment meant to determine the change of dimensions that may occur due to the increase of temperature of the orthopedic heels. The 3D model is manufactured using ethylene‐vinyl acetyl, also known as EVA, a copolymer made of ethylene and vinyl acetyl, which is very flexible and light weighted, also impermeable and UV and shock resistant. Five of the most used materials are analyzed during the experiment Orange Support, Blue Comfort, Multicolor, Green Relax, and Yellow Soft. Dimensions measurements are also taken five times a day for 5 days and recorded in tables and diagrams using Excel tools.In order to perform a statistical analysis of the results, the F‐Anova test is used and applied upon the recorded values. The conclusion is that there is a significant change of dimensions in the orthopedic heels materials that might affect the comfort of the users in certain conditions.
- 16 April 2021
- Published by Wiley in Macromolecular Symposia
- Vol. 396 (1) , 2100011
Experimental Analysis of Corrective Insoles Materials
The corrective static insole is a medical device meant to protect and support the locomotion system. In case of afflictions or lesions of this system, the insoles play a part in healing and rehabilitation. This study aims at analyzing a personalized insole, designed according to rapid prototyping approach with low expenses in order to assist the rehabilitation of pathologies like flat foot and adjacent complications, redistribution of plantar pressures at feet level but also adjusting postural attitude of walking and standing. The insole is developed following a thorough medical examination in order to establish a diagnosis and then an expert in biomechanics and medical engineering will design the product according to the subject's needs and anthropometric dimensions. The paper also performs the analysis of the materials used for manufacturing the corrective insoles, especially from mechanical point of view by determining the static and dynamic loads that may act upon the device. The study is conducted in Solidworks software environment and provides a finite element analysis of the material used for the personalized insole, in order to provide an efficient and convenient methodology in supporting feet imbalance following a pathology.
- 16 April 2021
- Published by Wiley in Macromolecular Symposia
- Vol. 396 (1) , 2100011
Experimental Analysis of Corrective Insoles Materials
The corrective static insole is a medical device meant to protect and support the locomotion system. In case of afflictions or lesions of this system, the insoles play a part in healing and rehabilitation. This study aims at analyzing a personalized insole, designed according to rapid prototyping approach with low expenses in order to assist the rehabilitation of pathologies like flat foot and adjacent complications, redistribution of plantar pressures at feet level but also adjusting postural attitude of walking and standing. The insole is developed following a thorough medical examination in order to establish a diagnosis and then an expert in biomechanics and medical engineering will design the product according to the subject's needs and anthropometric dimensions. The paper also performs the analysis of the materials used for manufacturing the corrective insoles, especially from mechanical point of view by determining the static and dynamic loads that may act upon the device. The study is conducted in Solidworks software environment and provides a finite element analysis of the material used for the personalized insole, in order to provide an efficient and convenient methodology in supporting feet imbalance following a pathology.
- 20 November 2020
- Published by Springer Nature
- p. 217-223
Research on Speech Changes Due to Environmental Noise
- 20 November 2020
- Published by Springer Nature
- p. 217-223
Research on Speech Changes Due to Environmental Noise
- 20 November 2020
- Published by Springer Nature
- p. 297-303
Human Factor Balance Under the Influence of Variable Sound Frequency and Orientation
- 20 November 2020
- Published by Springer Nature
- p. 297-303
Human Factor Balance Under the Influence of Variable Sound Frequency and Orientation
- 17 May 2019
- Published by Springer Nature
- p. 335-339
Identifying Relevant Research Directions for Graduation Projects in Medical Engineering
- 17 May 2019
- Published by Springer Nature
- p. 335-339
Identifying Relevant Research Directions for Graduation Projects in Medical Engineering
- 17 May 2019
- Published by Springer Nature
- p. 29-34
Analysis of Postural Imbalance Due to Handling Weights During Physical Activities
- 17 May 2019
- Published by Springer Nature
- p. 29-34
Analysis of Postural Imbalance Due to Handling Weights During Physical Activities
- 21 December 2017
- Published by Springer Nature
- p. 189-199
Influence of Sound Physical Characteristics on Some Human Physiological Parameters
- 21 December 2017
- Published by Springer Nature
- p. 189-199
Influence of Sound Physical Characteristics on Some Human Physiological Parameters
- 21 December 2017
- Published by Springer Nature
- p. 113-119
Analysis of Acoustic Response and Treatment of a Rehabilitated Lecture Room
- 21 December 2017
- Published by Springer Nature
- p. 113-119
Analysis of Acoustic Response and Treatment of a Rehabilitated Lecture Room
- 16 March 2017
- Published by Springer Nature
- p. 345-350
Study upon the Mechanical Properties of Most Used Dental Restoration Materials
- 16 March 2017
- Published by Springer Nature
- p. 345-350
Study upon the Mechanical Properties of Most Used Dental Restoration Materials