Kamel Frigui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kamel Frigui has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Stephane Bila
University of Limoges, CNRS, XLIM UMR 7252, Limoges, France
6 shared publications - Corinne Dejous
Univ. Bordeaux, Bordeaux INP, CNRS, IMS, UMR 5218, 351 Cours de la Liberation, Talence, 33400, France
4 shared publications - Dominique Baillargeat
University of Limoges, CNRS, XLIM UMR 7252, F-87060 Limoges, France
4 shared publications - Hamida Hallil
Univ. Bordeaux, Bordeaux INP, CNRS, IMS UMR 5218, F-33405 Talence, France
4 shared publications - Aymen Abdelghani
University of Limoges/CNRS, XLIM, UMR 7252
3 shared publications - Carlos Paragua
University of Lille, CNRS, IEMN, UMR 8520
3 shared publications
Latest Publications
- Open Access
CNT-Based Inkjet-Printed RF Gas Sensor: Modification of Substrate Properties during the Fabrication Process
This paper presents the feasibility of a fully inkjet-printed, microwave flexible gas sensor based on a resonant electromagnetic transducer in microstrip technology and the impact of the printing process that affects the characteristics of the gas sensor. The sensor is fabricated using silver ink and multi-wall carbon nanotubes (MWCNTs) embedded in poly (3,4-ethylenedioxythiophene) polystyrene (PEDOT: PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. Particular attention is paid to the characterization of the printed materials and the paper substrate. The manufacturing process results in a change in relative permittivity of the paper substrate by nearly 20%. Electrical characterization, made in the presence of gas, validates our theoretical approach and the radiofrequency (RF) gas sensor proof of concept.
Open AccessCNT-Based Inkjet-Printed RF Gas Sensor: Modification of Substrate Properties during the Fabrication Process
This paper presents the feasibility of a fully inkjet-printed, microwave flexible gas sensor based on a resonant electromagnetic transducer in microstrip technology and the impact of the printing process that affects the characteristics of the gas sensor. The sensor is fabricated using silver ink and multi-wall carbon nanotubes (MWCNTs) embedded in poly (3,4-ethylenedioxythiophene) polystyrene (PEDOT: PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. Particular attention is paid to the characterization of the printed materials and the paper substrate. The manufacturing process results in a change in relative permittivity of the paper substrate by nearly 20%. Electrical characterization, made in the presence of gas, validates our theoretical approach and the radiofrequency (RF) gas sensor proof of concept.
- 6 September 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 28 (6) , 1365-1378
Chemical sensor based on a novel capacitive microwave flexible transducer with polymer nanocomposite-carbon nanotube sensitive film
- 6 September 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 28 (6) , 1365-1378
Chemical sensor based on a novel capacitive microwave flexible transducer with polymer nanocomposite-carbon nanotube sensitive film
- 18 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. PP (1536125X) , 1
VOCs monitoring using differential microwave capacitive resonant transducer and conductive PEDOT:PSS-MWCNTs nanocomposite film for environmental applications
This paper presents the feasibility of a low-cost fully inkjet printed capacitive microwave flexible gas sensor based on a resonant electromagnetic transducer in micro-strip technology with poly (3,4-ethylenedioxythiophene) polystyrene sulfonate and multi wall carbon nanotubes (PEDOT:PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. The design and simulation results of the device on paper substrate for differential measurements are first described. This theoretical study based on both analytical and Finite Element Model approaches, validates the operating principle. The fabrication process and experimental devices are then presented, as well as electrical characterization results, both in air and under selected vapor analytes. These experimental results show the good sensor repeatability and sensitivity according to the transmission S parameter resonant frequency shift equal to -2.153 kHz/ppm and -1.855 kHz/ppm for ethanol and toluene vapor concentrations from 500 to 1300 ppm, respectively. This leads to conclude on promising future of such passive sensors and further integration into real-time multi-sensing platform adaptable for the Internet of Things (IoT).
- 18 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. PP (1536125X) , 1
VOCs monitoring using differential microwave capacitive resonant transducer and conductive PEDOT:PSS-MWCNTs nanocomposite film for environmental applications
This paper presents the feasibility of a low-cost fully inkjet printed capacitive microwave flexible gas sensor based on a resonant electromagnetic transducer in micro-strip technology with poly (3,4-ethylenedioxythiophene) polystyrene sulfonate and multi wall carbon nanotubes (PEDOT:PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. The design and simulation results of the device on paper substrate for differential measurements are first described. This theoretical study based on both analytical and Finite Element Model approaches, validates the operating principle. The fabrication process and experimental devices are then presented, as well as electrical characterization results, both in air and under selected vapor analytes. These experimental results show the good sensor repeatability and sensitivity according to the transmission S parameter resonant frequency shift equal to -2.153 kHz/ppm and -1.855 kHz/ppm for ethanol and toluene vapor concentrations from 500 to 1300 ppm, respectively. This leads to conclude on promising future of such passive sensors and further integration into real-time multi-sensing platform adaptable for the Internet of Things (IoT).
- Open Access
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 439
Chemical Gas Sensor Based on a Flexible Capacitive Microwave Transducer Associated with a Sensitive Carbon Composite Polymer Film
This communication presents results on the feasibility of an inkjet printed chemical gas sensor suitable for a real time multi-sensing platform. The prototype targets volatile organic compounds (VOCs) such as ethanol vapor to monitor environmental pollution. The designed and ink-jet printed microwave sensor is presented. Preliminary results have shown the influence of ethanol vapor on the electrical properties of the sensor at microwave frequency range. The sensor’s sensitivity to ethanol vapor has been estimated to −2.48 kHz/ppm. The final aim of this work is to develop a low cost sensor for Internet of Things (IoT) applications.
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 439
Open AccessChemical Gas Sensor Based on a Flexible Capacitive Microwave Transducer Associated with a Sensitive Carbon Composite Polymer Film
This communication presents results on the feasibility of an inkjet printed chemical gas sensor suitable for a real time multi-sensing platform. The prototype targets volatile organic compounds (VOCs) such as ethanol vapor to monitor environmental pollution. The designed and ink-jet printed microwave sensor is presented. Preliminary results have shown the influence of ethanol vapor on the electrical properties of the sensor at microwave frequency range. The sensor’s sensitivity to ethanol vapor has been estimated to −2.48 kHz/ppm. The final aim of this work is to develop a low cost sensor for Internet of Things (IoT) applications.
- 12 July 2013
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 24 (2) , 249-258
Design and implementation of compact diplexers using dual-mode cavities
In this paper, the design of compact diplexers with dual-mode cavities for satellite payloads is detailed. Compact diplexers are composed of coupled resonators without additional waveguide element, leading to a more compact architecture. Two topologies are first implemented and compared with a standard manifold output diplexer, in terms of electrical performances, compactness, and power handling. Hardware prototypes are fabricated and measured for experimental verification. A third topology is finally introduced for the design of noncontiguous diplexers. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:249–258, 2014.
- 12 July 2013
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 24 (2) , 249-258
Design and implementation of compact diplexers using dual-mode cavities
In this paper, the design of compact diplexers with dual-mode cavities for satellite payloads is detailed. Compact diplexers are composed of coupled resonators without additional waveguide element, leading to a more compact architecture. Two topologies are first implemented and compared with a standard manifold output diplexer, in terms of electrical performances, compactness, and power handling. Hardware prototypes are fabricated and measured for experimental verification. A third topology is finally introduced for the design of noncontiguous diplexers. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:249–258, 2014.
- 18 January 2013
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 24 (1) , 46-54
Modeling and characterization of microwave breakdown at atmospheric pressure in OMUX filters
For output multiplexer (OMUX) filters placed in telecommunication satellites, microwave breakdown happens in an involuntary and undesirable way during tests at atmospheric pressure. This avalanche phenomenon is due to exponential growth of the electronic density caused by thermoelectronic emission under strong electromagnetic field magnitude. In this paper, our objective is to model and characterize experimentally multipole OMUX filters composed with coupled cavities. For identifying the element responsible for the breakdown, the electric field is calculated within each cavity and each iris. In order to characterize the breakdown phenomenon, we proposed an experimental test bench and we measured the power, both at the input and at the output of the filter. The article details the theoretical breakdown prediction and the experimental setup for such a structure. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:46–54, 2014.
- 18 January 2013
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 24 (1) , 46-54
Modeling and characterization of microwave breakdown at atmospheric pressure in OMUX filters
For output multiplexer (OMUX) filters placed in telecommunication satellites, microwave breakdown happens in an involuntary and undesirable way during tests at atmospheric pressure. This avalanche phenomenon is due to exponential growth of the electronic density caused by thermoelectronic emission under strong electromagnetic field magnitude. In this paper, our objective is to model and characterize experimentally multipole OMUX filters composed with coupled cavities. For identifying the element responsible for the breakdown, the electric field is calculated within each cavity and each iris. In order to characterize the breakdown phenomenon, we proposed an experimental test bench and we measured the power, both at the input and at the output of the filter. The article details the theoretical breakdown prediction and the experimental setup for such a structure. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:46–54, 2014.