Anna Sedláková
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anna Sedláková has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ladislav Tazky
Technical University of Košice
3 shared publications - Eva Krídlová Burdová
Technical University of Košice
2 shared publications - Pavol Majdlen
Institute of Architectural Engineering
2 shared publications - Silvia Vilčeková
Technical University of Košice
2 shared publications - Dušan Burák
Institute of Architectural Engineering, Faculty of Civil Engineering, Technical University of Kosice, 042 00 Kosice, Slovakia
1 shared publication - Iveta Selecká
Institute of Environmental Engineering, Faculty of Civil Engineering, Technical University of Kosice, Vysokoskolska 4, 042 00 Kosice, Slovakia
1 shared publication
Latest Publications
- Open Access
- 12 August 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (16) , 6524
Evaluation of Family Houses in Slovakia Using a Building Environmental Assessment System
The presented study is focused on the verification of a Building Environmental Assessment System (BEAS). A total of 13 detached family houses representing typical construction sites in Slovakia were chosen for analysis, evaluation and certification by using a BEAS which contains several main fields: A—Site Selection and Project Planning; B—Building Construction; C—Indoor Environment; D—Energy Performance; E—Water Management; and F—Waste Management. The results of this study show that the current construction method for family houses does not respect the criteria of sustainable construction as much as it possibly can. The reason for this is that investment costs for construction are prioritized over environmental and social aspects. Therefore, one house with a score of 1.10 is certified as BEAS BRONZE, ten family houses with scores of 1.56–2.88 are certified as BEAS SILVER and only two family houses with total scores of 3.59 and 3.87, respectively, are certified as BEAS GOLD. The overall results show that the weakest fields of sustainability are Waste management, Energy performance and Building construction. The best-rated fields are Site Selection and Project Planning, Indoor Environment and Water Management. In the future, it is essential to pay attention to those areas where the sustainability criteria have not been reached, as well as to raise project teams’ awareness of sustainability issues and subsequently to transfer them to building practices.
- 12 August 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (16) , 6524
Open AccessEvaluation of Family Houses in Slovakia Using a Building Environmental Assessment System
The presented study is focused on the verification of a Building Environmental Assessment System (BEAS). A total of 13 detached family houses representing typical construction sites in Slovakia were chosen for analysis, evaluation and certification by using a BEAS which contains several main fields: A—Site Selection and Project Planning; B—Building Construction; C—Indoor Environment; D—Energy Performance; E—Water Management; and F—Waste Management. The results of this study show that the current construction method for family houses does not respect the criteria of sustainable construction as much as it possibly can. The reason for this is that investment costs for construction are prioritized over environmental and social aspects. Therefore, one house with a score of 1.10 is certified as BEAS BRONZE, ten family houses with scores of 1.56–2.88 are certified as BEAS SILVER and only two family houses with total scores of 3.59 and 3.87, respectively, are certified as BEAS GOLD. The overall results show that the weakest fields of sustainability are Waste management, Energy performance and Building construction. The best-rated fields are Site Selection and Project Planning, Indoor Environment and Water Management. In the future, it is essential to pay attention to those areas where the sustainability criteria have not been reached, as well as to raise project teams’ awareness of sustainability issues and subsequently to transfer them to building practices.
- Open Access
- 1 December 2019
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 14 (2) , 51-60
Assessment of two different methods of calculating a heating demand
Phenomenon of today′s era is lowering overall energy performance and greenhouse gas emissions. European Union and its members came from an “uncontrollable” fossil fuel usage to an era of dependence reduction from fossil fuel usage. EU industry is now in era of utilizing renewable energy sources. Construction industry is responsible for 40% of total energy performance of EU; hence the great emphasis on energy effective design on new buildings as well as importance on energy effective renovation of already constructed buildings. Effort on lowering total energy performance in construction industry has signed on research on new project solutions, new insulation materials and new building services technologies which are maximizing energy gain from renewable energy sources. Simulation software and different engines are more than helpful tool when predicting building thermal behaviour. That is why simulation software is used more often in the process of designing energy efficient buildings or in the process of energy performance optimization of existing buildings. simulation and analytics itself, is dealing with simulation of chosen buildings (family houses) on heating demand based on the newest knowledge of constructions and materials. Results of heating demands of different family houses were confronted against heating demands calculated according national standards – using non-variable conditions. Next, the differences between two calculation approaches were characterized in percentages.
- 1 December 2019
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 14 (2) , 51-60
Open AccessAssessment of two different methods of calculating a heating demand
Phenomenon of today′s era is lowering overall energy performance and greenhouse gas emissions. European Union and its members came from an “uncontrollable” fossil fuel usage to an era of dependence reduction from fossil fuel usage. EU industry is now in era of utilizing renewable energy sources. Construction industry is responsible for 40% of total energy performance of EU; hence the great emphasis on energy effective design on new buildings as well as importance on energy effective renovation of already constructed buildings. Effort on lowering total energy performance in construction industry has signed on research on new project solutions, new insulation materials and new building services technologies which are maximizing energy gain from renewable energy sources. Simulation software and different engines are more than helpful tool when predicting building thermal behaviour. That is why simulation software is used more often in the process of designing energy efficient buildings or in the process of energy performance optimization of existing buildings. simulation and analytics itself, is dealing with simulation of chosen buildings (family houses) on heating demand based on the newest knowledge of constructions and materials. Results of heating demands of different family houses were confronted against heating demands calculated according national standards – using non-variable conditions. Next, the differences between two calculation approaches were characterized in percentages.
- 23 June 2015
- Published by Springer Nature
- p. 541-546
Solutions of Ground Floor for Energy Efficient Buildings—Economic Evaluation
- 23 June 2015
- Published by Springer Nature
- p. 541-546
Solutions of Ground Floor for Energy Efficient Buildings—Economic Evaluation
- 23 June 2015
- Published by Springer Nature
- p. 299-304
Modeling the Air Channel Ventilation in Ansys CFX of a Romanesque Church
- 23 June 2015
- Published by Springer Nature
- p. 299-304
Modeling the Air Channel Ventilation in Ansys CFX of a Romanesque Church
- 11 April 2015
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 17 (5) , 1323-1332
Analysis of material solutions for design of construction details of foundation, wall and floor for energy and environmental impacts
- 11 April 2015
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 17 (5) , 1323-1332
Analysis of material solutions for design of construction details of foundation, wall and floor for energy and environmental impacts
- 10 January 2015
- Published by Rzeszow University of Technology in Journal of Civil Engineering, Environment and Architecture
- Vol. XXXII (4/2015) , 195-200
REQUIREMENT ТO THE FRESH AIR IN THE CONGREGATION ROOM
- 10 January 2015
- Published by Rzeszow University of Technology in Journal of Civil Engineering, Environment and Architecture
- Vol. XXXII (4/2015) , 195-200
REQUIREMENT ТO THE FRESH AIR IN THE CONGREGATION ROOM
- 27 October 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1041, 105-108
Possible Solutions for Ground Slabs of Energy Efficient Buildings
The building envelope is a barrier that separates the internal environment from the effects of weather. This barrier ought to facilitate the optimal comfort of the interior environment in winter as well as summer. It has been shown in practice that most building defects occur within the building envelope. This includes external walls, roofs and floors too, and is impartial to new or renovated buildings. Heat losses of buildings through external constructions – roof, external walls, ground slabs are not negligible. It is therefore important to pay more attention to these construction elements. Basementless buildings situated on the ground are in direct contact with the subgrade and its thermal state. An amount of heat primarily destined for the creation of thermal comfort in the interior escapes from the baseplate to the cooler subgrade. The outgoing heat represents heat losses, which unfavourably affect the overall energy efficiency of the building. The heat losses represent approximately 15 to 20 % of the overall heat losses of the building. This number is a clear antecedent for the need to isolate and minimalize heat flow from the building to the subgrade.
- 27 October 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1041, 105-108
Possible Solutions for Ground Slabs of Energy Efficient Buildings
The building envelope is a barrier that separates the internal environment from the effects of weather. This barrier ought to facilitate the optimal comfort of the interior environment in winter as well as summer. It has been shown in practice that most building defects occur within the building envelope. This includes external walls, roofs and floors too, and is impartial to new or renovated buildings. Heat losses of buildings through external constructions – roof, external walls, ground slabs are not negligible. It is therefore important to pay more attention to these construction elements. Basementless buildings situated on the ground are in direct contact with the subgrade and its thermal state. An amount of heat primarily destined for the creation of thermal comfort in the interior escapes from the baseplate to the cooler subgrade. The outgoing heat represents heat losses, which unfavourably affect the overall energy efficiency of the building. The heat losses represent approximately 15 to 20 % of the overall heat losses of the building. This number is a clear antecedent for the need to isolate and minimalize heat flow from the building to the subgrade.
- Open Access
- 1 November 2013
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 8 (2) , 115-122
Optimization of the Energy Performance of a Low Energy House Based on Sensitivity Analysis
For buildings with for heating requirements, energy balance is based on the difference between two similarly large numbers (heat gain and heat loss) in which the calculation becomes increasingly sensitive to changes in parameters. The output of the hourly simulation method illustrates the temperature in “free-floating” mode, which unlike the requirement for heating provides better information on the thermal behavior of the building itself in order to model the dynamic response of the object to certain changes in the input data. For the purpose of the evaluation the minimum and maximum acceptable temperature and the area within the boundaries called comfort zone. In this paper a low energy house is evaluated in terms of energy performance and thermal comfort, where some parameters are altered in order to determine its sensitivity to fluctuations. The methodology is based on a sensitivity analysis (SA) and Monte Carlo simulation based on a stochastic random selection. Thermal comfort is evaluated using an adaptive thermal comfort.
- 1 November 2013
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 8 (2) , 115-122
Open AccessOptimization of the Energy Performance of a Low Energy House Based on Sensitivity Analysis
For buildings with for heating requirements, energy balance is based on the difference between two similarly large numbers (heat gain and heat loss) in which the calculation becomes increasingly sensitive to changes in parameters. The output of the hourly simulation method illustrates the temperature in “free-floating” mode, which unlike the requirement for heating provides better information on the thermal behavior of the building itself in order to model the dynamic response of the object to certain changes in the input data. For the purpose of the evaluation the minimum and maximum acceptable temperature and the area within the boundaries called comfort zone. In this paper a low energy house is evaluated in terms of energy performance and thermal comfort, where some parameters are altered in order to determine its sensitivity to fluctuations. The methodology is based on a sensitivity analysis (SA) and Monte Carlo simulation based on a stochastic random selection. Thermal comfort is evaluated using an adaptive thermal comfort.
- Open Access
- 1 November 2013
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 8 (2) , 51-60
CFD Proposals for the Layout of Air Vents for Realization of Underfloor Air Cavity Created from Special Fittings
In basement acting humidity can be removed using ventilated flooring created from special fittings. Particular attention should be paid to the design layout of inlet and outlet of openings. The aim of the correct proposal is the even distribution of air flow over the whole surface of the cavity. To achieve this state and to objective evaluate the air flow in the gaps, which are made up of shaped objects, the work uses CFD simulations. Based on computational simulations, structural designs of underfloor air cavities created using special fittings are designed. As results are the proposals for the layout of air vents for historic buildings for realization in Kosice.
- 1 November 2013
- Published by Walter de Gruyter GmbH in Selected Scientific Papers - Journal of Civil Engineering
- Vol. 8 (2) , 51-60
Open AccessCFD Proposals for the Layout of Air Vents for Realization of Underfloor Air Cavity Created from Special Fittings
In basement acting humidity can be removed using ventilated flooring created from special fittings. Particular attention should be paid to the design layout of inlet and outlet of openings. The aim of the correct proposal is the even distribution of air flow over the whole surface of the cavity. To achieve this state and to objective evaluate the air flow in the gaps, which are made up of shaped objects, the work uses CFD simulations. Based on computational simulations, structural designs of underfloor air cavities created using special fittings are designed. As results are the proposals for the layout of air vents for historic buildings for realization in Kosice.