Takeshi Mitani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Takeshi Mitani has a total of 118 co-authors. Here are the top co-authors by number of shared publications:
- Hajime Okumura
National Institute of Advanced Industrial Science and Technology (AIST) 3 , 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568, Japan
28 shared publications Tomohisa Kato
National Institute of Advanced Industrial Science and Technology (AIST) Onogawa
27 shared publicationsNaoyoshi Komatsu
15 shared publicationsHajime Okumura
National Institute of Advanced Industrial Science and Technology
9 shared publicationsTetsuo Takahashi
9 shared publicationsS. Nakashima
National Institute of Advanced Industrial Science and Technology, Advanced Power Electronics Research Center 1 , Umezono 1-1-1, Central 2, Tsukuba, Ibaraki 305-8568, Japan
8 shared publications
Latest Publications
- 18 July 2026
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 26 (15) , 5847-5854
Macrostep Flow Behavior in 4H-SiC Solution Growth with Different Solvent Compositions and Its Correlation with the Conversion Efficiency of Threading Screw Dislocations
The influence of solvent additives on macrostep flow behavior during SiC solution growth was investigated with a particular emphasis on interactions between macrosteps and threading screw dislocations (TSDs). Using Si, Si–5 mol % Al, and Si–5 mol % Ti solvents, we found that the Si–Ti solvent showed a remarkable enhancement of lateral macrostep flow, with a flow distance per unit growth thickness approximately 1 order of magnitude larger than those for the other solvents. Morphological analyses revealed that macrosteps formed with the Si–Ti solvent exhibit smaller slope angles, which kinetically favor lateral macrostep flow under identical solute diffusion conditions. Ti addition also reduced the nanometer-scale step density on macroterraces by nearly 2 orders of magnitude compared with Al addition, thereby suppressing vertical growth on terraces. This reduced step density on macroterraces shifts solute consumption preferentially toward macrosteps, further enhancing their lateral growth. This increases the interaction frequency between the macrosteps and TSDs, thus improving the TSD conversion efficiency. These findings demonstrate that the TSD conversion efficiency is governed not by static macrostep geometry alone, but by the dynamic lateral macrostep flow behavior. This kinetic insight provides useful guidance for achieving effective dislocation reduction during SiC solution growth.
- 18 July 2026
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 26 (15) , 5847-5854
Macrostep Flow Behavior in 4H-SiC Solution Growth with Different Solvent Compositions and Its Correlation with the Conversion Efficiency of Threading Screw Dislocations
The influence of solvent additives on macrostep flow behavior during SiC solution growth was investigated with a particular emphasis on interactions between macrosteps and threading screw dislocations (TSDs). Using Si, Si–5 mol % Al, and Si–5 mol % Ti solvents, we found that the Si–Ti solvent showed a remarkable enhancement of lateral macrostep flow, with a flow distance per unit growth thickness approximately 1 order of magnitude larger than those for the other solvents. Morphological analyses revealed that macrosteps formed with the Si–Ti solvent exhibit smaller slope angles, which kinetically favor lateral macrostep flow under identical solute diffusion conditions. Ti addition also reduced the nanometer-scale step density on macroterraces by nearly 2 orders of magnitude compared with Al addition, thereby suppressing vertical growth on terraces. This reduced step density on macroterraces shifts solute consumption preferentially toward macrosteps, further enhancing their lateral growth. This increases the interaction frequency between the macrosteps and TSDs, thus improving the TSD conversion efficiency. These findings demonstrate that the TSD conversion efficiency is governed not by static macrostep geometry alone, but by the dynamic lateral macrostep flow behavior. This kinetic insight provides useful guidance for achieving effective dislocation reduction during SiC solution growth.
- 6 March 2024
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 24 (6) , 2526-2532
Suppression of SiC Inclusions in 4H-SiC Crystals Grown from Si–Cr–C-Based Solution Saturated with SiC
- 6 March 2024
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 24 (6) , 2526-2532
Suppression of SiC Inclusions in 4H-SiC Crystals Grown from Si–Cr–C-Based Solution Saturated with SiC
- Open Access
- 10 April 2023
- Published by Surface Science Society Japan in Vacuum and Surface Science
- Vol. 66 (4) , 215-220
Analysis of Defect Propagation in SiC Crystals Formed by Solution Growth and Sublimation Growth and High Quality SiC Crystal Growth by the Hybrid Method Combining both Growth Techniques
We have investigated the propagation of threading screw dislocations (TSD) in the hybrid growth that combines solution growth and sublimation growth. The higher TSD conversion ratio in solution growth is attributed not only to the macrostep height but also to the lateral flow speed of macrosteps which increases the interaction between TSDs and macrosteps. In sublimation growth in the hybrid process, the basal plane defect can be eliminated efficiently by 15° off growth. The energetic stability and activation barrier in the conversion between TSD and basal plane defect have been discussed.
- 10 April 2023
- Published by Surface Science Society Japan in Vacuum and Surface Science
- Vol. 66 (4) , 215-220
Open AccessAnalysis of Defect Propagation in SiC Crystals Formed by Solution Growth and Sublimation Growth and High Quality SiC Crystal Growth by the Hybrid Method Combining both Growth Techniques
We have investigated the propagation of threading screw dislocations (TSD) in the hybrid growth that combines solution growth and sublimation growth. The higher TSD conversion ratio in solution growth is attributed not only to the macrostep height but also to the lateral flow speed of macrosteps which increases the interaction between TSDs and macrosteps. In sublimation growth in the hybrid process, the basal plane defect can be eliminated efficiently by 15° off growth. The energetic stability and activation barrier in the conversion between TSD and basal plane defect have been discussed.
- 1 August 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 568-569
Reduction of threading screw dislocations in 4H-SiC crystals by a hybrid method with solution growth and physical vapor transport growth
- 1 August 2021
- Published by Elsevier in Journal of Crystal Growth
- Vol. 568-569
Reduction of threading screw dislocations in 4H-SiC crystals by a hybrid method with solution growth and physical vapor transport growth
- 28 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1004, 427-432
Formation of Double Shockley Stacking Faults in Heavily Nitrogen Doped 4H-SiC Crystal with Reduction of Residual Stress around Scratch Damage
The scratch damage that caused the generation of double Shockley stacking faults (DSFs) in heavily nitrogen doped 4H-SiC crystal was investigated quantitatively. Scratch tests were carried out on 4H-SiC substrates with a nitrogen concentration of 2.6 × 1019 cm-3. A residual tensile stress of 40 MPa was detected around the scratch loaded at 30 mN with a diamond tip. DSFs were generated from this scratch by annealing at 1100°C for 2 h in Ar atmosphere. After annealing, the residual stress around the scratch was reduced to a tensile stress of 10 MPa. This result suggests that the reduction of residual stress around the scratch coincided with the formation of DSFs.
- 28 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1004, 427-432
Formation of Double Shockley Stacking Faults in Heavily Nitrogen Doped 4H-SiC Crystal with Reduction of Residual Stress around Scratch Damage
The scratch damage that caused the generation of double Shockley stacking faults (DSFs) in heavily nitrogen doped 4H-SiC crystal was investigated quantitatively. Scratch tests were carried out on 4H-SiC substrates with a nitrogen concentration of 2.6 × 1019 cm-3. A residual tensile stress of 40 MPa was detected around the scratch loaded at 30 mN with a diamond tip. DSFs were generated from this scratch by annealing at 1100°C for 2 h in Ar atmosphere. After annealing, the residual stress around the scratch was reduced to a tensile stress of 10 MPa. This result suggests that the reduction of residual stress around the scratch coincided with the formation of DSFs.
- 28 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1004, 224-230
Anomalous Conduction between the Band and Nearest-Neighbor Hopping Conduction Regions in Heavily Al-Doped p-Type 4H-SiC
We measure the temperature-dependent resistivity (ρ(T)) for thick heavily Al- and Ncodoped p-type 4H-SiC samples grown by chemical vapor deposition (CVD), physical vapor transport (PVT), and solution growth (SG), and investigate their conduction mechanisms. For samples with an Al concentration (CAl) of 3.5×1019 to 1×1020 cm-3 grown by CVD, PVT, and SG, the conduction mechanisms at high and low temperatures are band and nearest-neighbor hopping (NNH) conduction, respectively. In the range CAl of 1×1019 to 3.5×1019 cm-3, on the other hand, an anomalous conduction, referred to as X conduction here, is observed between the band and NNH conduction regions for the samples grown by CVD and PVT, but not those grown by SG. One of the differences between the samples grown by CVD and PVT and those grown by SG is the off-orientation toward [11-20] of the (0001) 4H-SiC substrate. We discuss the reason for the appearance of X conduction, which appears to be consistent with dopant-concentration inhomogeneity model.
- 28 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1004, 224-230
Anomalous Conduction between the Band and Nearest-Neighbor Hopping Conduction Regions in Heavily Al-Doped p-Type 4H-SiC
We measure the temperature-dependent resistivity (ρ(T)) for thick heavily Al- and Ncodoped p-type 4H-SiC samples grown by chemical vapor deposition (CVD), physical vapor transport (PVT), and solution growth (SG), and investigate their conduction mechanisms. For samples with an Al concentration (CAl) of 3.5×1019 to 1×1020 cm-3 grown by CVD, PVT, and SG, the conduction mechanisms at high and low temperatures are band and nearest-neighbor hopping (NNH) conduction, respectively. In the range CAl of 1×1019 to 3.5×1019 cm-3, on the other hand, an anomalous conduction, referred to as X conduction here, is observed between the band and NNH conduction regions for the samples grown by CVD and PVT, but not those grown by SG. One of the differences between the samples grown by CVD and PVT and those grown by SG is the off-orientation toward [11-20] of the (0001) 4H-SiC substrate. We discuss the reason for the appearance of X conduction, which appears to be consistent with dopant-concentration inhomogeneity model.