Tomohito Takubo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tomohito Takubo has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Tatsuo Arai
Osaka University
33 shared publications - Yasushi Mae
Osaka University
19 shared publications - Kenji Inoue
Yamagata University
17 shared publications - Kenichi Ohara
Osaka University
13 shared publications - Takahiro Miyauchi
Osaka University
3 shared publications Takuya Kaminade
3 shared publications
Latest Publications
- Open Access
- 1 January 2013
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 79 (797) , 1-16
Obstacle Avoidance for Multi-Legged Robot Using Virtual Impedance Model
- 1 January 2013
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 79 (797) , 1-16
Open AccessObstacle Avoidance for Multi-Legged Robot Using Virtual Impedance Model
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 78 (793) , 3186-3201
High Resolution Grid Map with Normal Distribution Transform Algorithm
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 78 (793) , 3186-3201
High Resolution Grid Map with Normal Distribution Transform Algorithm
- Open Access
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2010, _2A2-D18_1
2A2-D18 Personal space for the humanoid robot and a presentation method
Personal space between two human beings is very important. If humans and humanoid robots are to coexist in the same environment, the personal space between them has to be taken into consideration, too. We have evaluated the personal space between a person and a humanoid robot through an experiment using a real robot and a VR robot. If the results about a VR robot and a real robot are not different, the personal space can be evaluated in the future by VR only. As a result of our experiment, we have found that the personal space between a person and a humanoid robot matches to personal distance which is seen between two persons who are in a relationship of friendship/acquaintanceship. Also, no differences were seen in the shapes of personal space for a real robot and a VR robot, respectively.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2010, _2A2-D18_1
Open Access2A2-D18 Personal space for the humanoid robot and a presentation method
Personal space between two human beings is very important. If humans and humanoid robots are to coexist in the same environment, the personal space between them has to be taken into consideration, too. We have evaluated the personal space between a person and a humanoid robot through an experiment using a real robot and a VR robot. If the results about a VR robot and a real robot are not different, the personal space can be evaluated in the future by VR only. As a result of our experiment, we have found that the personal space between a person and a humanoid robot matches to personal distance which is seen between two persons who are in a relationship of friendship/acquaintanceship. Also, no differences were seen in the shapes of personal space for a real robot and a VR robot, respectively.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2010, _2P1-A29_1
2P1-A29 Development of automatic cell supply system with solenoid valve
Micro tasks dealing with live cells and tissues in bio science and technology require dexterous and skillful manipulation under microscope, and are mostly executed manually. Microfluidic cell manipulation techniques are being developed to achieve their automation to improve the manipulation productivity. We are developing a cell supply system, where devising efficient valve is the key issue. We propose a solenoid valve system to improve its breaking capability. The new valve has higher responsibility than our previous air actuated valve. We have integrated an automatic cell supply system with this valve and the experiments confirm successful cell supply.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2010, _2P1-A29_1
2P1-A29 Development of automatic cell supply system with solenoid valve
Micro tasks dealing with live cells and tissues in bio science and technology require dexterous and skillful manipulation under microscope, and are mostly executed manually. Microfluidic cell manipulation techniques are being developed to achieve their automation to improve the manipulation productivity. We are developing a cell supply system, where devising efficient valve is the key issue. We propose a solenoid valve system to improve its breaking capability. The new valve has higher responsibility than our previous air actuated valve. We have integrated an automatic cell supply system with this valve and the experiments confirm successful cell supply.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Abstracts of the international conference on advanced mechatronics : toward evolutionary fusion of IT and mechatronics : ICAM
- Vol. 2010.5, 545-550
Development of RSSI Measurement Sensor Modules for Robust Position Estimation of Wireless Sensor Network Node
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Abstracts of the international conference on advanced mechatronics : toward evolutionary fusion of IT and mechatronics : ICAM
- Vol. 2010.5, 545-550
Development of RSSI Measurement Sensor Modules for Robust Position Estimation of Wireless Sensor Network Node
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-H11_1
2A1-H11 Position Estimation Method Using RSSI Measuring Sensors
Recently, sensor network is one of the key technologies on robotic field. Especially, position estimation of sensor node is important technology on sensor network. However, in indoor environment, pisition estimation using radio signal strength indication (RSSI) is difficult, because of multipath fading. In this paper, to solve this problem and take advantage the RF communication, we propose distance measurement sensor using RSSI based on 125kHz, which is less subject to multipath fading. And, the stability of this sensor is shown through several expriments.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-H11_1
2A1-H11 Position Estimation Method Using RSSI Measuring Sensors
Recently, sensor network is one of the key technologies on robotic field. Especially, position estimation of sensor node is important technology on sensor network. However, in indoor environment, pisition estimation using radio signal strength indication (RSSI) is difficult, because of multipath fading. In this paper, to solve this problem and take advantage the RF communication, we propose distance measurement sensor using RSSI based on 125kHz, which is less subject to multipath fading. And, the stability of this sensor is shown through several expriments.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-D05_1
2A1-D05 Development of Robust Object Pose Estimation Component
The paper reports a RT Component for estimation 3D pose of a target object and design for usability by considering robot function. The RT Component extracts SIFT features from input images, and detect a target object by matching the SIFT features of the reference image to the SIFT features of the image. Then object pose is estimated based on correspondences of the features. Experimental results show the performance of the RT Component for several target objects. The RT component can detect a target object robustly in complex backgrounds of human daily life space.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-D05_1
2A1-D05 Development of Robust Object Pose Estimation Component
The paper reports a RT Component for estimation 3D pose of a target object and design for usability by considering robot function. The RT Component extracts SIFT features from input images, and detect a target object by matching the SIFT features of the reference image to the SIFT features of the image. Then object pose is estimated based on correspondences of the features. Experimental results show the performance of the RT Component for several target objects. The RT component can detect a target object robustly in complex backgrounds of human daily life space.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-C21_1
2A1-C21 Evaluation of Indications for Action Indication System in Emergency Situation
The paper describes presentation methods for action indication systems. Easy-to-understand presentation is required for a person in panic in emergency situations. Presentation methods using audio speakers and projectors have been proposed for a real-time action indication system. Audio and/or visual indications are considered and an experimental system is constructed. Basic presentation methods using audio and/or visual indications are evaluated by experiments.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-C21_1
2A1-C21 Evaluation of Indications for Action Indication System in Emergency Situation
The paper describes presentation methods for action indication systems. Easy-to-understand presentation is required for a person in panic in emergency situations. Presentation methods using audio speakers and projectors have been proposed for a real-time action indication system. Audio and/or visual indications are considered and an experimental system is constructed. Basic presentation methods using audio and/or visual indications are evaluated by experiments.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-E07_1
2A1-E07 Continuous Rough Terrain Walking by Using ZMP Criteria Map
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-E07_1
2A1-E07 Continuous Rough Terrain Walking by Using ZMP Criteria Map
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-J06_1
2A1-J06 Automated Cell Supply Module : The Design of Valve System and Branch Shape for Cell Transport in a Microfluidic Chip
We studied the cell supply system for automation of the cell cloning work. Our aim of this system is the efficient and stable supply some type of cells, egg cells or fibroblasts, to microfluidic chips.In this report, we present the design of air valve system and branch shape for cell transport. For valve system, we made two types of microfluidic chips, one is two layer chip and another is three layer chip. The pneumatic pressure valves were applied in or onto chips, blocked up the flow channel with each method, and changed flow passes.
- 1 January 2009
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2009, _2A1-J06_1
2A1-J06 Automated Cell Supply Module : The Design of Valve System and Branch Shape for Cell Transport in a Microfluidic Chip
We studied the cell supply system for automation of the cell cloning work. Our aim of this system is the efficient and stable supply some type of cells, egg cells or fibroblasts, to microfluidic chips.In this report, we present the design of air valve system and branch shape for cell transport. For valve system, we made two types of microfluidic chips, one is two layer chip and another is three layer chip. The pneumatic pressure valves were applied in or onto chips, blocked up the flow channel with each method, and changed flow passes.