Toshiharu Kagawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Toshiharu Kagawa has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
Kenji Kawashima
35 shared publicationsToshinori Fujita
16 shared publications- Tatsuya Funaki
Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama, Japan. Tel : +81-45-924-5486
8 shared publications - Maolin Cai
School of Automation Science and Electrical Engineering, Beihang University, Beijing 100191, China
6 shared publications Tomonori Kato
5 shared publicationsKazutoshi Sakaki
4 shared publications
Latest Publications
- Open Access
- 13 September 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (9) , 941
A New Method for Analysing the Pressure Response Delay in a Pneumatic Brake System Caused by the Influence of Transmission Pipes
This study aims to propose an analysis method for resolving the pressure response of a pneumatic brake circuit considering the effect of a transmission pipe. Pneumatic brake systems (PBS) are widely used in commercial vehicles. The pressure response characteristic of the PBS is the key factor affecting braking performance. By using the thermodynamics of a variable-quality system, the pressure response model of the brake chamber is established, which includes the dynamic model of the pipe considering the unsteady friction and heat transfer. The partial-differential control equations of pipe are solved by introducing the constrained interpolation profile (CIP) method, and a virtual chamber model is proposed to set the boundary condition so as to solve the pressure response in the brake chamber simultaneously. Thus, the regularity of the brake pressure response is obtained by considering the influence of the pipe. Lastly, the model is verified experimentally. The present study indicates that the main factors that affect the pressure response delay are the pipe length and the combination forms of the sonic conductances of the orifices inlet and outlet. Furthermore, it helps to verify that the CIP method is an effective way of solving the pressure response of a brake circuit because of its high accuracy. The present study serves as a foundation for the design and analysis of a PBS.
- 13 September 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (9) , 941
Open AccessA New Method for Analysing the Pressure Response Delay in a Pneumatic Brake System Caused by the Influence of Transmission Pipes
This study aims to propose an analysis method for resolving the pressure response of a pneumatic brake circuit considering the effect of a transmission pipe. Pneumatic brake systems (PBS) are widely used in commercial vehicles. The pressure response characteristic of the PBS is the key factor affecting braking performance. By using the thermodynamics of a variable-quality system, the pressure response model of the brake chamber is established, which includes the dynamic model of the pipe considering the unsteady friction and heat transfer. The partial-differential control equations of pipe are solved by introducing the constrained interpolation profile (CIP) method, and a virtual chamber model is proposed to set the boundary condition so as to solve the pressure response in the brake chamber simultaneously. Thus, the regularity of the brake pressure response is obtained by considering the influence of the pipe. Lastly, the model is verified experimentally. The present study indicates that the main factors that affect the pressure response delay are the pipe length and the combination forms of the sonic conductances of the orifices inlet and outlet. Furthermore, it helps to verify that the CIP method is an effective way of solving the pressure response of a brake circuit because of its high accuracy. The present study serves as a foundation for the design and analysis of a PBS.
- Open Access
- 9 August 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (8) , 816
Analysis of the Energy Efficiency of a Pneumatic Booster Regulator with Energy Recovery
Pneumatic booster regulators (PBR) are in great demand in modern pneumatic systems for their energy-saving abilities. A new booster regulator with energy recovery (VBA-R) was proposed, and its energy efficiency was investigated by introducing the concept of air power. On the basis of quality-alterable gas thermodynamics, an energy efficiency assessment and pressure response model for VBA-R was proposed. First, a model was solved using MATLAB/Simulink software, and an alternative experiment was designed to verify the mathematical model and performance improvement. The results showed that the simulation was consistent with the experiment. We also can conclude that, first of all, the energy efficiency decreases with the increasing of supply pressure and flow-rate consumption; a VBA-R has the highest efficiency when its diameter ratio is closest to 1.3. Finally, a recovery chamber helped to improve the performance of the VBA-R, which included a boost ratio improvement of 15–25% and an efficiency improvement of 5–10% compared with a conventional VBA booster regulator. This research lays the foundation for optimism regarding the proposed booster regulator.
- 9 August 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (8) , 816
Open AccessAnalysis of the Energy Efficiency of a Pneumatic Booster Regulator with Energy Recovery
Pneumatic booster regulators (PBR) are in great demand in modern pneumatic systems for their energy-saving abilities. A new booster regulator with energy recovery (VBA-R) was proposed, and its energy efficiency was investigated by introducing the concept of air power. On the basis of quality-alterable gas thermodynamics, an energy efficiency assessment and pressure response model for VBA-R was proposed. First, a model was solved using MATLAB/Simulink software, and an alternative experiment was designed to verify the mathematical model and performance improvement. The results showed that the simulation was consistent with the experiment. We also can conclude that, first of all, the energy efficiency decreases with the increasing of supply pressure and flow-rate consumption; a VBA-R has the highest efficiency when its diameter ratio is closest to 1.3. Finally, a recovery chamber helped to improve the performance of the VBA-R, which included a boost ratio improvement of 15–25% and an efficiency improvement of 5–10% compared with a conventional VBA booster regulator. This research lays the foundation for optimism regarding the proposed booster regulator.
- 22 April 2016
- Published by ASME International in Journal of Fluids Engineering
- Vol. 138 (7) , 071102
Experimental Study of Pressure Drop-Flow Rate Characteristics of Heated Tight Porous Materials
Tight porous materials are used as pneumatic components in a wide range of industrial applications. Such porous materials contain thousands of interconnected irregular micropores, which produce a large pressure drop (ΔP) between the upstream and downstream sides of the porous material when a fluid flows through it. The relationship between the pressure drop and flow rate (i.e., ΔP-G characteristics) is a very important basic characteristic. Temperature is one of the factors that affect the ΔP-G characteristics because variations in temperature change the viscosity and density of the fluid. In this study, we experimentally analyzed the ΔP-G characteristics of tight porous materials by heating them using an electromagnetic system. First, we experimentally investigated the change in the ΔP-G curve under the condition of constant heating power. Then, based on the Darcy–Forchheimer theory, we introduced an experimental method to determine the average temperature of the fluid. The results show that the temperature reaches approximately 500 K in the small flow rate range, which produces considerable changes in the ΔP-G curve. As the flow rate increases, the temperature decreases, and thus, the ΔP-G curve at constant heating power converges to the curve for the room temperature. Furthermore, we compared three porous materials with different permeability coefficients and porosities and analyzed the effect of these parameters on the ΔP-G characteristics. We also performed experiments at different downstream pressures to study the effect of the average density on the ΔP-G characteristics.
- 22 April 2016
- Published by ASME International in Journal of Fluids Engineering
- Vol. 138 (7) , 071102
Experimental Study of Pressure Drop-Flow Rate Characteristics of Heated Tight Porous Materials
Tight porous materials are used as pneumatic components in a wide range of industrial applications. Such porous materials contain thousands of interconnected irregular micropores, which produce a large pressure drop (ΔP) between the upstream and downstream sides of the porous material when a fluid flows through it. The relationship between the pressure drop and flow rate (i.e., ΔP-G characteristics) is a very important basic characteristic. Temperature is one of the factors that affect the ΔP-G characteristics because variations in temperature change the viscosity and density of the fluid. In this study, we experimentally analyzed the ΔP-G characteristics of tight porous materials by heating them using an electromagnetic system. First, we experimentally investigated the change in the ΔP-G curve under the condition of constant heating power. Then, based on the Darcy–Forchheimer theory, we introduced an experimental method to determine the average temperature of the fluid. The results show that the temperature reaches approximately 500 K in the small flow rate range, which produces considerable changes in the ΔP-G curve. As the flow rate increases, the temperature decreases, and thus, the ΔP-G curve at constant heating power converges to the curve for the room temperature. Furthermore, we compared three porous materials with different permeability coefficients and porosities and analyzed the effect of these parameters on the ΔP-G characteristics. We also performed experiments at different downstream pressures to study the effect of the average density on the ΔP-G characteristics.
- 1 February 2015
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 61, 59-65
A method to suppress temperature increase in pneumatic artificial rubber muscles
- 1 February 2015
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 61, 59-65
A method to suppress temperature increase in pneumatic artificial rubber muscles
- 1 January 2014
- Published by The Japan Fluid Power Systems Society in TRANSACTIONS OF THE JAPAN FLUID POWER SYSTEM SOCIETY
- Vol. 45 (5) , 73-78
On the Leak Testing of Vessels by Compressed Air Charging
- 1 January 2014
- Published by The Japan Fluid Power Systems Society in TRANSACTIONS OF THE JAPAN FLUID POWER SYSTEM SOCIETY
- Vol. 45 (5) , 73-78
On the Leak Testing of Vessels by Compressed Air Charging
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _J113031-1
J113031 Ultra Precise Positioning of Air Guide Slight Movement Stage Driven by Pneumatic Bellows
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _J113031-1
J113031 Ultra Precise Positioning of Air Guide Slight Movement Stage Driven by Pneumatic Bellows
- 1 January 2012
- Published by The Visualization Society of Japan in Transactions of the Visualization Society of Japan
- Vol. 32 (6) , 9-14
Visualization of inward flow between two parallel disks
- 1 January 2012
- Published by The Visualization Society of Japan in Transactions of the Visualization Society of Japan
- Vol. 32 (6) , 9-14
Visualization of inward flow between two parallel disks
- 1 January 2011
- Published by The Japan Fluid Power Systems Society in TRANSACTIONS OF THE JAPAN FLUID POWER SYSTEM SOCIETY
- Vol. 42 (6) , 114-119
Proposal and Analysis of a Pneumatic Artificial Rubber Muscle with High-Damping Characteristics that uses a Rubber Bellows
- 1 January 2011
- Published by The Japan Fluid Power Systems Society in TRANSACTIONS OF THE JAPAN FLUID POWER SYSTEM SOCIETY
- Vol. 42 (6) , 114-119
Proposal and Analysis of a Pneumatic Artificial Rubber Muscle with High-Damping Characteristics that uses a Rubber Bellows
- 1 January 2010
- Published by ASME International
- p. 241-247
Computation of an Unsteady Orifice Flow in a Circular Pipe From Wall Pressure Measurements Based on Measurement-Integrated Simulation Using a Turbulent Model
Visualizing the state of real turbulent flow is important in many applications such as safe operation and fault diagnosis in plant or pipeline. Two approaches to this purpose exist: experimental measurement and numerical simulation. In experimental measurement, reliability of the result at measured point is easy to evaluate. However, information of the whole flow field is difficult to obtain. On the other hand, numerical simulation easily obtains any information of the flow field. However, the reliability of the result strongly depends on the numerical model and boundary condition and/or the initial condition. In general, the more precise results are needed, the heavier computation load we spend. None of these approaches is superior, and combination methods of them are subjected to extensive research. Above all, we particularly paid attention to measurement-integrated (MI) simulation proposed by Hayase et al. MI simulation can expect to reduce computational load. We have applied MI simulation to unsteady oscillatory airflows passing through an orifice. In our previous study, a standard k-ε model was used for MI simulation. Estimation error remained due to inadequate consideration of the feedback law. In our latest study, the feedback law was decided considering an effect of computation grid on CFD of contracted flow. As a result, wall pressures near the orifice plate and axial velocities on vena contracta estimated with MI simulation showed good agreement with that of measurement. In the present paper, we deal with visualization of unsteady oscillatory airflows passing through an orifice from wall pressure measurement based on MI simulation using a turbulent model. The former studies have used measured inlet flow rate which is unknown in many actual case. Compared with the flow rate measurement, wall pressure measurement is simple. Therefore, we consider MI simulation using only wall pressure are of practical use. The developed MI simulation was performed with unsteady flow rate with the frequency up to 10 Hz. Computation results obtained with the developed MI simulation using coarse computation grid is compared with experimental results. It is confirmed that flow field obtained with the developed MI simulation is close to that of experiment.
- 1 January 2010
- Published by ASME International
- p. 241-247
Computation of an Unsteady Orifice Flow in a Circular Pipe From Wall Pressure Measurements Based on Measurement-Integrated Simulation Using a Turbulent Model
Visualizing the state of real turbulent flow is important in many applications such as safe operation and fault diagnosis in plant or pipeline. Two approaches to this purpose exist: experimental measurement and numerical simulation. In experimental measurement, reliability of the result at measured point is easy to evaluate. However, information of the whole flow field is difficult to obtain. On the other hand, numerical simulation easily obtains any information of the flow field. However, the reliability of the result strongly depends on the numerical model and boundary condition and/or the initial condition. In general, the more precise results are needed, the heavier computation load we spend. None of these approaches is superior, and combination methods of them are subjected to extensive research. Above all, we particularly paid attention to measurement-integrated (MI) simulation proposed by Hayase et al. MI simulation can expect to reduce computational load. We have applied MI simulation to unsteady oscillatory airflows passing through an orifice. In our previous study, a standard k-ε model was used for MI simulation. Estimation error remained due to inadequate consideration of the feedback law. In our latest study, the feedback law was decided considering an effect of computation grid on CFD of contracted flow. As a result, wall pressures near the orifice plate and axial velocities on vena contracta estimated with MI simulation showed good agreement with that of measurement. In the present paper, we deal with visualization of unsteady oscillatory airflows passing through an orifice from wall pressure measurement based on MI simulation using a turbulent model. The former studies have used measured inlet flow rate which is unknown in many actual case. Compared with the flow rate measurement, wall pressure measurement is simple. Therefore, we consider MI simulation using only wall pressure are of practical use. The developed MI simulation was performed with unsteady flow rate with the frequency up to 10 Hz. Computation results obtained with the developed MI simulation using coarse computation grid is compared with experimental results. It is confirmed that flow field obtained with the developed MI simulation is close to that of experiment.