Charles F. Kutscher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Charles F. Kutscher has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Frank Burkholder
National Renewable Energy Laboratory, MS 5202, 1617 Cole Boulevard, Golden, CO 80401
1 shared publicationJ. Kathleen Stynes
Department of Mechanical Engineering, University of Colorado, Boulder, CO 80301
1 shared publication- Judy C. Netter
National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, CO 80401, USA
1 shared publication
Latest Publications
- 8 January 2014
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 136 (1) , 010907
A Method for Measuring the Optical Efficiency of Evacuated Receivers
Evacuated receivers used with parabolic trough solar collectors can be characterized in terms of their heat loss and optical efficiency. The optical efficiency is the ratio of the energy collected to the incident solar radiation when operating at ambient temperature. If one restricts attention to the active portion of the absorber receiving incident sunlight, this is equal to the product of the transmittance of the glass cover (τ) and the absorptance of the absorber surface (α). This paper describes a new outdoor transient test method for measuring the optical efficiency. An aluminum tube is inserted into the center of the stainless steel absorber tube, and the annulus between the two tubes is filled with a measured mass of aluminum shot. The receiver is precooled and then exposed on an outdoor test rig to solar radiation. The slopes of the temperature versus time curves for the aluminum filler and the steel tube are taken during a period of steady solar radiation and near the point at which the average glass temperature is close to the average absorber temperature (i.e., when there is minimal heat loss from the absorber tube to ambient). The slopes are then used to determine the optical efficiency. This method has the advantage of using the actual solar spectrum and has an uncertainty of about ±3%, which can be improved upon if a reference receiver is used for comparison. When this method was applied to the active section of the receiver tube, measurements of an actual receiver tube yielded a τα that, to within experimental uncertainty, is consistent with the manufacturer's values of τ and α.
- 8 January 2014
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 136 (1) , 010907
A Method for Measuring the Optical Efficiency of Evacuated Receivers
Evacuated receivers used with parabolic trough solar collectors can be characterized in terms of their heat loss and optical efficiency. The optical efficiency is the ratio of the energy collected to the incident solar radiation when operating at ambient temperature. If one restricts attention to the active portion of the absorber receiving incident sunlight, this is equal to the product of the transmittance of the glass cover (τ) and the absorptance of the absorber surface (α). This paper describes a new outdoor transient test method for measuring the optical efficiency. An aluminum tube is inserted into the center of the stainless steel absorber tube, and the annulus between the two tubes is filled with a measured mass of aluminum shot. The receiver is precooled and then exposed on an outdoor test rig to solar radiation. The slopes of the temperature versus time curves for the aluminum filler and the steel tube are taken during a period of steady solar radiation and near the point at which the average glass temperature is close to the average absorber temperature (i.e., when there is minimal heat loss from the absorber tube to ambient). The slopes are then used to determine the optical efficiency. This method has the advantage of using the actual solar spectrum and has an uncertainty of about ±3%, which can be improved upon if a reference receiver is used for comparison. When this method was applied to the active section of the receiver tube, measurements of an actual receiver tube yielded a τα that, to within experimental uncertainty, is consistent with the manufacturer's values of τ and α.
- 29 November 2011
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 134 (1) , 011012
Generation of a Parabolic Trough Collector Efficiency Curve From Separate Measurements of Outdoor Optical Efficiency and Indoor Receiver Heat Loss
The thermal efficiency of a parabolic trough collector is a function of both the fraction of direct normal radiation absorbed by the receiver (the optical efficiency) and the heat lost to the environment when the receiver is at operating temperature. The thermal efficiency can be determined by testing the collector under actual operating conditions or by separately measuring these two components. This paper describes how outdoor measurement of the optical efficiency is combined with laboratory measurements of receiver heat loss to obtain the thermal efficiency curve. This paper describes this approach and also makes the case that there are advantages to plotting collector efficiency versus the difference between the operating temperature and the ambient temperature at which the receiver heat loss was measured divided by radiation to a fractional power (on the order of 1/3 but obtained via data regression)—as opposed to the difference between operating and ambient temperatures divided by the radiation. The results are shown to be robust over wide ranges of ambient temperature, sky temperature, and wind speed.
- 29 November 2011
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 134 (1) , 011012
Generation of a Parabolic Trough Collector Efficiency Curve From Separate Measurements of Outdoor Optical Efficiency and Indoor Receiver Heat Loss
The thermal efficiency of a parabolic trough collector is a function of both the fraction of direct normal radiation absorbed by the receiver (the optical efficiency) and the heat lost to the environment when the receiver is at operating temperature. The thermal efficiency can be determined by testing the collector under actual operating conditions or by separately measuring these two components. This paper describes how outdoor measurement of the optical efficiency is combined with laboratory measurements of receiver heat loss to obtain the thermal efficiency curve. This paper describes this approach and also makes the case that there are advantages to plotting collector efficiency versus the difference between the operating temperature and the ambient temperature at which the receiver heat loss was measured divided by radiation to a fractional power (on the order of 1/3 but obtained via data regression)—as opposed to the difference between operating and ambient temperatures divided by the radiation. The results are shown to be robust over wide ranges of ambient temperature, sky temperature, and wind speed.