TGTandra Ghose

Tandra Ghose

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tandra Ghose has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Convexity vs. Implied-Closure in Figure-Ground Organization

    by Tandra Ghose, Ananya Mukherjee

    Convexity is a well established figural cue for figure-ground organization. However, it has an inherent implicit confound with closure based on the observation that if the shared-contour is extended on the convex side it will form a closed region. Thus, the relative influence of convexity and implied-closure is unknown. Here we describe our attempt to minimize this confound and empirically investigate whether convexity or implied-closure has a greater impact on determining figure-ground organization. The critical segment, “wings”, of the contour is the part located near the top and bottom of the shared-contour that slightly curves around to intersect the perpendicular-borders of the bipartite image. We created conflict “incongruent” stimuli by flipping the wings about the vertical axis to imply closure on the side opposite to convexity. Control “congruent” conditions were created by moving the position of the flipped-wings away from the perpendicular-edge towards the center of the contour. This resulted in net convexity matched to the incongruent-condition while congruency between convexity and implied-closure was not affected. Stimuli consisted of 128 bipartite black-white images with: 2 shapes of shared-contour (circle/triangle) of 2 sizes each (small/large); 2 wing sizes depending on the base shared-contour size (range 7%–20% of entire length); position of wings along the shared-contour (1 incongruent “UpDown” and 3 congruent “Up”, “Center”, “Down”). They were black/white and left/right counterbalanced. The observers made a figure-ground judgment after viewing the stimulus for 1 second and responded with a mouse click on left/right response buttons. Data from 40 participants show that the percentage figural response for the side with both convexity and implied-closure is 70%. However, in case of conflict, figural response fell to 50% for convexity-only-side vs. implied-closure-only-side. We conclude that the convexity reported as the figural cue is effective only when present with implied-closure and not otherwise.

  • Open Access

    Canonical Viewpoints for Videos of Assembly Tasks

    by Tandra Ghose, Katharina Mura, Markus Huff

    Canonical-views for static objects are defined as preferred-views that provide richer spatial information and richer cognitive processing (Palmer, Rosch, & Chase, 1981; Blanz, Tarr, & Bülthoff, 1999; Ghose & Liu, 2013). For simple dynamic scenes consisting of three moving balls on a flat surface, canonical-views provide richer information about temporal changes in the spatial relationships (Garsoffky, Huff, & Schwan, 2007; Garsoffky, Schwan, & Huff, 2009). In this research we ask (1) if there is a single canonical-view for an entire movie depicting an assembly task, and (2) if the canonical-view depends on a specific assembly-step or action-type. The stimuli consisted of three complex assembly tasks taken from a technical construction toolkit. Each scenario was recorded from 5 different viewpoints, namely, self, opposite-to-self, left, right and top. The mean assembly time per scenario was 4 min and 14 sec. The actor in the video was right-handed. There were 66 assembly-steps with 7 action-types. Procedure: A pair of video clips showing the same step appeared successively at two different positions on the screen. After the first showing, the videos were played back in a loop until the participant responded. The task was to choose the “better-view” for learning the assembly-step. Data from 20 participants show that canonical-view varies to some extent from assembly-step to assembly-step. The self and the opposite-to-self views were most-preferred 74% of the time. Left and right views were least-preferred 76% of the time. That is, views along the median plane were rated as “better” for learning than frontal and top plane for every action-type. An “unambiguity measure” was calculated for each assembly-step as mean frequency of (most minus least) preferred-views. Higher unambiguity values mean that the best perspective is unambiguously preferred. The median views are unambiguously preferred over other views suggesting these are canonical-views of actions. Meeting presented at VSS 2015

  • Open Access

    IBES: a tool for creating instructions based on event segmentation

    by Katharina Mura, Nils Petersen, Markus Huff, Tandra Ghose

    Receiving informative, well-structured, and well-designed instructions supports performance and memory in assembly tasks. We describe IBES, a tool with which users can quickly and easily create multimedia, step-by-step instructions by segmenting a video of a task into segments. In a validation study we demonstrate that the step-by-step structure of the visual instructions created by the tool corresponds to the natural event boundaries, which are assessed by event segmentation and are known to play an important role in memory processes. In one part of the study, twenty participants created instructions based on videos of two different scenarios by using the proposed tool. In the other part of the study, ten and twelve participants respectively segmented videos of the same scenarios yielding event boundaries for coarse and fine events. We found that the visual steps chosen by the participants for creating the instruction manual had corresponding events in the event segmentation. The number of instructional steps was a compromise between the number of fine and coarse events. Our interpretation of results is that the tool picks up on natural human event perception processes of segmenting an ongoing activity into events and enables the convenient transfer into meaningful multimedia instructions for assembly tasks. We discuss the practical application of IBES, for example, creating manuals for differing expertise levels, and give suggestions for research on user-oriented instructional design based on this tool.