Johnpaul Woodhead
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Johnpaul Woodhead has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
R. Grey
Department of Electronic and Electrical Engineering, University of Sheffield, Mappin Street, Sheffield, S1 3JD, United Kingdom
5 shared publications- Julian David Booker
University of Bristol, UK
3 shared publications A. S. Pabla
Department of Electronic and Electrical Engineering, University of Sheffield, P.O. Box 600, Mappin Street, Sheffield S1 4DU, United Kingdom
2 shared publicationsA.S. Pabla
Department of Electronic and Electrical Engineering, University of Sheffield, Mappin Street, Sheffield, S1 3JD, United Kingdom
2 shared publicationsG.J. Rees
Department of Electronic and Electrical Engineering, University of Sheffield, Mappin Street, Sheffield, S1 3JD, United Kingdom
2 shared publicationsJ.P.R. David
Department of Electronic and Electrical Engineering, University of Sheffield, Mappin Street, Sheffield, S1 3JD, United Kingdom
2 shared publications
Latest Publications
- Open Access
- 21 April 2015
- Published by WITPRESS LTD. in WIT transactions on engineering sciences
- Vol. 91, 141-152
Modelling of dynamic friction in the cold forming of plain spherical bearings
Nosing is a cold forming process used in the manufacture of plain spherical metal bearings. The process ensures the outer bearing race conforms to the...
- 21 April 2015
- Published by WITPRESS LTD. in WIT transactions on engineering sciences
- Vol. 91, 141-152
Open AccessModelling of dynamic friction in the cold forming of plain spherical bearings
Nosing is a cold forming process used in the manufacture of plain spherical metal bearings. The process ensures the outer bearing race conforms to the...
- 6 February 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 777, 58-64
Measurement of Forming Stresses in Plain Spherical Bearings Using Neutron Diffraction
Nosing is a cold metal-forming process used in the manufacture of plain spherical bearings. This process ensures the outer bearing race conforms to the shape of the inner race (a ball), with a composite liner in-between to provide a low frictional moment. These bearings must be precision engineered due to the large forces and demanding environments they operate within in service. The manufacture of these bearings and related process settings is very much an experiential route, although increasingly Finite Element simulations are used to predict and characterise complex material behaviour. It is imperative the numerical nosing models are validated against experimental measurements due to uncertainties in material properties, process variables and part manufacture variations. In this paper, neutron diffraction is used to determine the residual stresses in a large nosed bearing. Measurements were made on the POLDI instrument at PSI, Switzerland. This paper compares the predicted stresses with measurement results, and draws conclusions concerning the validity and usability of the models.
- 6 February 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 777, 58-64
Measurement of Forming Stresses in Plain Spherical Bearings Using Neutron Diffraction
Nosing is a cold metal-forming process used in the manufacture of plain spherical bearings. This process ensures the outer bearing race conforms to the shape of the inner race (a ball), with a composite liner in-between to provide a low frictional moment. These bearings must be precision engineered due to the large forces and demanding environments they operate within in service. The manufacture of these bearings and related process settings is very much an experiential route, although increasingly Finite Element simulations are used to predict and characterise complex material behaviour. It is imperative the numerical nosing models are validated against experimental measurements due to uncertainties in material properties, process variables and part manufacture variations. In this paper, neutron diffraction is used to determine the residual stresses in a large nosed bearing. Measurements were made on the POLDI instrument at PSI, Switzerland. This paper compares the predicted stresses with measurement results, and draws conclusions concerning the validity and usability of the models.
- 6 September 2012
- Published by Springer Nature
- p. 327-337
Modelling of Nosing for the Assembly of Aerospace Bearings
- 6 September 2012
- Published by Springer Nature
- p. 327-337
Modelling of Nosing for the Assembly of Aerospace Bearings
- 22 May 1997
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 33 (11) , 957-958
Low threshold InGaAs/AlGaAs lasers grown on (111)BGaAs substrate
The authors report the lowest threshold current density to date of a strained InGaAs/GaAs/AlGaAs single quantum well separate confinement heterostructure laser grown on a (111)B GaAs substrate. A Jth value as low as 87 A/cm2 has been obtained for a 2500 µm long broad area laser. The internal quantum efficiency is estimated to be 82% and the internal loss is 5.5 cm-1.
- 22 May 1997
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 33 (11) , 957-958
Low threshold InGaAs/AlGaAs lasers grown on (111)BGaAs substrate
The authors report the lowest threshold current density to date of a strained InGaAs/GaAs/AlGaAs single quantum well separate confinement heterostructure laser grown on a (111)B GaAs substrate. A Jth value as low as 87 A/cm2 has been obtained for a 2500 µm long broad area laser. The internal quantum efficiency is estimated to be 82% and the internal loss is 5.5 cm-1.
- 1 December 1995
- Published by Elsevier in Microelectronics Journal
- Vol. 26 (8) , 811-820
Growth of pseudomorphic InGaAs/GaAs quantum wells on [111]B GaAs for strained layer, piezoelectric, optoelectronic devices
- 1 December 1995
- Published by Elsevier in Microelectronics Journal
- Vol. 26 (8) , 811-820
Growth of pseudomorphic InGaAs/GaAs quantum wells on [111]B GaAs for strained layer, piezoelectric, optoelectronic devices
- 1 November 1994
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 76 (9) , 5447-5452
Carrier screening effects in piezoelectric strained InGaAs/GaAs quantum wells grown on the [111]B axis
Excitation‐power‐dependent blue shifts in photoluminescence and electroluminescence are studied in piezoelectric strained layer multiple quantum wells (MQWs) incorporated in p‐i‐n diodes. By investigating MQWs with different geometric structures and controlling external bias it is demonstrated that, in contrast to previous studies, these blue shifts cannot always be attributed to long‐range screening across a MQW and that screening must take place due to charge redistribution within individual wells. The results provide design rules to ensure this latter screening mechanism, which is subject to fast recovery.
- 1 November 1994
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 76 (9) , 5447-5452
Carrier screening effects in piezoelectric strained InGaAs/GaAs quantum wells grown on the [111]B axis
Excitation‐power‐dependent blue shifts in photoluminescence and electroluminescence are studied in piezoelectric strained layer multiple quantum wells (MQWs) incorporated in p‐i‐n diodes. By investigating MQWs with different geometric structures and controlling external bias it is demonstrated that, in contrast to previous studies, these blue shifts cannot always be attributed to long‐range screening across a MQW and that screening must take place due to charge redistribution within individual wells. The results provide design rules to ensure this latter screening mechanism, which is subject to fast recovery.
- 1 November 1992
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 4 (11) , 1192-1194
Wide operating wavelength range and low threshold current In/sub 0.24/Ga/sub 0.76/As/GaAs vertical-cavity surface-emitting lasers
Very low threshold current density operation of triple quantum well vertical-cavity surface-emitting lasers (VCSELs) is reported. The active wells are strained In/sub 0.24/Ga/sub 0.76/As in GaAs. Devices from the same wafer operate at room temperature over a wavelength range of 958-1042 nm, with a minimum threshold current density of 366 A-cm/sup -2/ at 1018 nm. The dependence of threshold current on wavelength gives an insight into the optical gain spectrum of the quantum wells. It was shown that 50- mu m-diameter devices operate CW without heatsinking.
- 1 November 1992
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 4 (11) , 1192-1194
Wide operating wavelength range and low threshold current In/sub 0.24/Ga/sub 0.76/As/GaAs vertical-cavity surface-emitting lasers
Very low threshold current density operation of triple quantum well vertical-cavity surface-emitting lasers (VCSELs) is reported. The active wells are strained In/sub 0.24/Ga/sub 0.76/As in GaAs. Devices from the same wafer operate at room temperature over a wavelength range of 958-1042 nm, with a minimum threshold current density of 366 A-cm/sup -2/ at 1018 nm. The dependence of threshold current on wavelength gives an insight into the optical gain spectrum of the quantum wells. It was shown that 50- mu m-diameter devices operate CW without heatsinking.
- Open Access
- 30 September 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 59 (14) , 1670-1672
Bistable self-electro-optic operation of strained In0.1Ga0.9As/GaAs asymmetric Fabry–Perot modulators
We report bistable operation of a strained‐layer InGaAs/GaAs asymmetric Fabry–Perot optical modulator configured as a self‐electro‐optic effect device (SEED) operating in reflection mode. Bistable loops are observed from 949 to 962 nm with switching powers down to submicrowatt levels. The contrast ratio between on and off states is as large as 5:1 (7 dB) and the device will hold in either state indefinitely. A 600‐μm‐diam device has a switching time of 20 μs for 2.1 fJ μm−2 switching energy. Large optical latch arrays are envisaged using this device.
- 30 September 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 59 (14) , 1670-1672
Open AccessBistable self-electro-optic operation of strained In0.1Ga0.9As/GaAs asymmetric Fabry–Perot modulators
We report bistable operation of a strained‐layer InGaAs/GaAs asymmetric Fabry–Perot optical modulator configured as a self‐electro‐optic effect device (SEED) operating in reflection mode. Bistable loops are observed from 949 to 962 nm with switching powers down to submicrowatt levels. The contrast ratio between on and off states is as large as 5:1 (7 dB) and the device will hold in either state indefinitely. A 600‐μm‐diam device has a switching time of 20 μs for 2.1 fJ μm−2 switching energy. Large optical latch arrays are envisaged using this device.