Raoudha Gaha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Raoudha Gaha has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Abdelmajid Benamara
Université de Monastir
4 shared publications- Abdelmajid Benamara
University of Monastir
2 shared publications Bernard Yannou
Ecole Centrale Paris
2 shared publications- Bernard Yannou
CentraleSupélec, Université Paris-Saclay
2 shared publications Abdelfattah Mlika
Université de Sousse
1 shared publicationFaïda Mhenni
QUARTZ EA7393, SUPMECA-Paris
1 shared publication
Latest Publications
- Open Access
- 8 November 2022
- Published by IOS Press
- p. 173-178
Multi-Objective Optimization of Cutting Parameters and Toolpaths in Pocket Milling Considering Energy Savings and Machining Costs
Productivity gains and minimum environmental impacts is the new challenge faced by enterprises, industries, and researchers. Mechanical machining is one of the widely used techniques in manufacturing. So, it's important to accurately and effectively estimate and optimize the overall ecological and economic footprint. Since, cutting energy and machining cost is proportional to machining time, production-costs minimization could be achieved by embracing machining time reduction strategies. These may include the use of more efficient toolpath strategies that reduces machining time, therefore, ecological and economic costs. In the literature, many studies have focused on minimizing cost and environmental impact by examining the entire machining process, while the environmental/economic flow of toolpaths is relatively unexplored. The implementation and selection of a cutting path strategy with appropriate cutting parameters has a significant impact on machining costs. The purpose of this paper is to examine the impact of toolpath strategies in pocket machining. The cutting parameters considered are cutting speed, feed, depth of cut and feed. The aim will be addressed by means of using Taguchi parameter design. This could further raise the integrity of sustainable machining strategies in an earlier step of machining processes.
- 8 November 2022
- Published by IOS Press
- p. 173-178
Open AccessMulti-Objective Optimization of Cutting Parameters and Toolpaths in Pocket Milling Considering Energy Savings and Machining Costs
Productivity gains and minimum environmental impacts is the new challenge faced by enterprises, industries, and researchers. Mechanical machining is one of the widely used techniques in manufacturing. So, it's important to accurately and effectively estimate and optimize the overall ecological and economic footprint. Since, cutting energy and machining cost is proportional to machining time, production-costs minimization could be achieved by embracing machining time reduction strategies. These may include the use of more efficient toolpath strategies that reduces machining time, therefore, ecological and economic costs. In the literature, many studies have focused on minimizing cost and environmental impact by examining the entire machining process, while the environmental/economic flow of toolpaths is relatively unexplored. The implementation and selection of a cutting path strategy with appropriate cutting parameters has a significant impact on machining costs. The purpose of this paper is to examine the impact of toolpath strategies in pocket machining. The cutting parameters considered are cutting speed, feed, depth of cut and feed. The aim will be addressed by means of using Taguchi parameter design. This could further raise the integrity of sustainable machining strategies in an earlier step of machining processes.
- 27 February 2020
- Published by Springer Nature in Lecture Notes in Mechanical Engineering
- p. 55-63
Design of an Electronic Throttle Body Based on a New Knowledge Sharing Engineering Methodology
- 27 February 2020
- Published by Springer Nature in Lecture Notes in Mechanical Engineering
- p. 55-63
Design of an Electronic Throttle Body Based on a New Knowledge Sharing Engineering Methodology
- 4 December 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (3-4) , 1057-1068
Proposal of new eco-manufacturing feature interaction-based methodology in CAD phase
- 4 December 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (3-4) , 1057-1068
Proposal of new eco-manufacturing feature interaction-based methodology in CAD phase
- 25 November 2017
- Published by Springer Nature
- p. 763-770
Proposition of Eco-Feature: A New CAD/PLM Data Model for an LCA Tool
- 25 November 2017
- Published by Springer Nature
- p. 763-770
Proposition of Eco-Feature: A New CAD/PLM Data Model for an LCA Tool
- 9 July 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 87 (5-8) , 1335-1343
Selection of a green manufacturing process based on CAD features
- 9 July 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 87 (5-8) , 1335-1343
Selection of a green manufacturing process based on CAD features
- 1 January 2015
- Published by Springer Nature
- p. 21-27
An Environmental Impact/Cost Model for Evaluating Multiple Feature-Based Machining Methods
- 1 January 2015
- Published by Springer Nature
- p. 21-27
An Environmental Impact/Cost Model for Evaluating Multiple Feature-Based Machining Methods
- 1 July 2014
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 15 (7) , 1443-1451
A new eco-design approach on CAD systems
- 1 July 2014
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 15 (7) , 1443-1451
A new eco-design approach on CAD systems