Ralph W. Moir
Ralph W. Moir has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
M Z Youssef
2 shared publicationsR H Bulmer
2 shared publicationsT K Fowler
2 shared publications- T. D. Rognlien
Lawrence Livermore National Laboratory
1 shared publication - T. Kenneth Fowler
University of California Berkeley Nuclear Engineering, USA
1 shared publication - Thomas C. Simonen
Lawrence Livermore National Laboratory, Berkeley, CA, United States of America
1 shared publication
Latest Publications
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1771 (1) , 080003
Prospects for an axisymmetric advanced fuel tandem mirror
We describe a new axisymmetric tandem mirror concept which incorporates advances in physics understanding, recent experimental results and developing technologies. The tandem mirror concept consists of two small high magnetic field axisymmetric mirrors at the ends a solenoidal central cell which axially confines a high beta fusion plasma. High energy neutral beam Injection and high frequency electron cyclotron heating power are applied to the end cells which operate at higher density and temperature to provide both magnetic mirror as well as electrostatic axial plasma confinement of the ignited central cell plasma. Designs fueled with DT and, cat-DD are considered indicating a wide design space warranting further analysis as well as experimental investigations.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1771 (1) , 080003
Prospects for an axisymmetric advanced fuel tandem mirror
We describe a new axisymmetric tandem mirror concept which incorporates advances in physics understanding, recent experimental results and developing technologies. The tandem mirror concept consists of two small high magnetic field axisymmetric mirrors at the ends a solenoidal central cell which axially confines a high beta fusion plasma. High energy neutral beam Injection and high frequency electron cyclotron heating power are applied to the end cells which operate at higher density and temperature to provide both magnetic mirror as well as electrostatic axial plasma confinement of the ignited central cell plasma. Designs fueled with DT and, cat-DD are considered indicating a wide design space warranting further analysis as well as experimental investigations.
- 8 April 2002
- Published by Office of Scientific and Technical Information (OSTI)
Thick Liquid-Walled Spheromak Magnetic Fusion Power Plant
We assume a spheromak configuration can be made and sustained by a steady gun current, which injects particles, current and magnetic field, i.e., helicity injection. The equilibrium is calculated with an MHD equilibrium code, where an average beta of 10% is found. The toroidal current of 40 MA is sustained by an injection current of 100 kA (125 MW of gun power). The flux linking the gun is 1/1000th that of the flux in the spheromak. The geometry allows a flow of liquid, either molten salt, (flibe-Li{sub 2}BeF{sub 4} or flinabe-LiNaBeF{sub 4}) or liquid metal such as SnLi which protects most of the walls and structures from neutron damage. The free surface between the liquid and the burning plasma is heated by bremsstrahlung and optical radiation and neutrons from the plasma. The temperature of the free surface of the liquid is calculated and then the evaporation rate is estimated. The impurity concentration in the burning plasma is estimated and limited to a 20% reduction in the fusion power. For a high radiating edge plasma, the divertor power density of 460 MW/m{sup 2} is handled by high-speed (20 m/s), liquid jets. For low radiating edge plasmas, the divertor-power density of 1860more » MW/m{sup 2} is too high to handle for flibe but possibly acceptable for SnLi with jets of 100 m/s flow speed. Calculations show the tritium breeding is adequate with enriched Li and appropriate design of the walls not covered by flowing liquid 15% of the total. We have come up with a number of problem areas needing further study to make the design self consistent and workable. « less
- 8 April 2002
- Published by Office of Scientific and Technical Information (OSTI)
Thick Liquid-Walled Spheromak Magnetic Fusion Power Plant
We assume a spheromak configuration can be made and sustained by a steady gun current, which injects particles, current and magnetic field, i.e., helicity injection. The equilibrium is calculated with an MHD equilibrium code, where an average beta of 10% is found. The toroidal current of 40 MA is sustained by an injection current of 100 kA (125 MW of gun power). The flux linking the gun is 1/1000th that of the flux in the spheromak. The geometry allows a flow of liquid, either molten salt, (flibe-Li{sub 2}BeF{sub 4} or flinabe-LiNaBeF{sub 4}) or liquid metal such as SnLi which protects most of the walls and structures from neutron damage. The free surface between the liquid and the burning plasma is heated by bremsstrahlung and optical radiation and neutrons from the plasma. The temperature of the free surface of the liquid is calculated and then the evaporation rate is estimated. The impurity concentration in the burning plasma is estimated and limited to a 20% reduction in the fusion power. For a high radiating edge plasma, the divertor power density of 460 MW/m{sup 2} is handled by high-speed (20 m/s), liquid jets. For low radiating edge plasmas, the divertor-power density of 1860more » MW/m{sup 2} is too high to handle for flibe but possibly acceptable for SnLi with jets of 100 m/s flow speed. Calculations show the tritium breeding is adequate with enriched Li and appropriate design of the walls not covered by flowing liquid 15% of the total. We have come up with a number of problem areas needing further study to make the design self consistent and workable. « less