Youfang Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Youfang Hu has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Frederic Y. Gardes
Univ. of Southampton (United Kingdom)
3 shared publications- Goran Z. Mashanovich
Adv. Technol. Inst., Univ. of Surrey, Guildford
3 shared publications - Ali Z. Khokhar
Optoelectronics Research Centre, University of Southampton, Southampton, Hampshire United Kingdom of Great Britain and Northern Ireland
2 shared publications - Colin J. Mitchell
Optoelectronics Research Centre, University of Southampton, Southampton, SO17 1BJ, UK
2 shared publications D. J. Thomson
Optoelectronics Research Centre, University of Southampton, Southampton SO17 1BJ, UK
2 shared publications- David J. Thomson
Optoelectronics Research Centre, University of Southampton, Southampton, U.K.
2 shared publications
Latest Publications
- Open Access
Design Procedure and Fabrication of Reproducible Silicon Vernier Devices for High-Performance Refractive Index Sensing
In this paper, we propose a generalized procedure for the design of integrated Vernier devices for high performance chemical and biochemical sensing. In particular, we demonstrate the accurate control of the most critical design and fabrication parameters of silicon-on-insulator cascade-coupled racetrack resonators operating in the second regime of the Vernier effect, around 1.55 μm. The experimental implementation of our design strategies has allowed a rigorous and reliable investigation of the influence of racetrack resonator and directional coupler dimensions as well as of waveguide process variability on the operation of Vernier devices. Figures of merit of our Vernier architectures have been measured experimentally, evidencing a high reproducibility and a very good agreement with the theoretical predictions, as also confirmed by relative errors even lower than 1%. Finally, a Vernier gain as high as 30.3, average insertion loss of 2.1 dB and extinction ratio up to 30 dB have been achieved.
Open AccessDesign Procedure and Fabrication of Reproducible Silicon Vernier Devices for High-Performance Refractive Index Sensing
In this paper, we propose a generalized procedure for the design of integrated Vernier devices for high performance chemical and biochemical sensing. In particular, we demonstrate the accurate control of the most critical design and fabrication parameters of silicon-on-insulator cascade-coupled racetrack resonators operating in the second regime of the Vernier effect, around 1.55 μm. The experimental implementation of our design strategies has allowed a rigorous and reliable investigation of the influence of racetrack resonator and directional coupler dimensions as well as of waveguide process variability on the operation of Vernier devices. Figures of merit of our Vernier architectures have been measured experimentally, evidencing a high reproducibility and a very good agreement with the theoretical predictions, as also confirmed by relative errors even lower than 1%. Finally, a Vernier gain as high as 30.3, average insertion loss of 2.1 dB and extinction ratio up to 30 dB have been achieved.
- 27 February 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9367, 936704
Fabrication error tolerant SOI WDM device using bidirectional angled multimode interferometers
We have demonstrated a bidirectional wavelength division (de)multiplexer (WDM) on the silicon-on-insulator platform. An excellent match of the peak transmission wavelength of each channel between the two AMMIs was achieved. This type of device is ideal for integrated optical transceivers where the transmission wavelengths are required to match with the receiving wavelengths. The device also benefits from simple fabrication (as only a single lithography and etching step is required), improved convenience for the transceiver layout design, a reduction in tuning power and circuitry, and efficient use of layout space.
- 27 February 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9367, 936704
Fabrication error tolerant SOI WDM device using bidirectional angled multimode interferometers
We have demonstrated a bidirectional wavelength division (de)multiplexer (WDM) on the silicon-on-insulator platform. An excellent match of the peak transmission wavelength of each channel between the two AMMIs was achieved. This type of device is ideal for integrated optical transceivers where the transmission wavelengths are required to match with the receiving wavelengths. The device also benefits from simple fabrication (as only a single lithography and etching step is required), improved convenience for the transceiver layout design, a reduction in tuning power and circuitry, and efficient use of layout space.
- 5 March 2014
- Published by Optica Publishing Group in Optics Letters
- Vol. 39 (6) , 1406-1409
Mid-infrared wavelength division (de)multiplexer using an interleaved angled multimode interferometer on the silicon-on-insulator platform
A low-cost and high-performance wavelength division (de)multiplexing structure in the mid-IR wavelength range is demonstrated on the silicon-on-insulator platform using an interleaved angled multimode interferometer (AMMI). As compared to a single AMMI, the channel count was doubled and the channel spacing halved with negligible extra insertion loss and crosstalk and with only a slight increase in device footprint. The device requires only single lithography and etching steps for fabrication. Potential is also shown for achieving improved performance with further optimized design.
- 5 March 2014
- Published by Optica Publishing Group in Optics Letters
- Vol. 39 (6) , 1406-1409
Mid-infrared wavelength division (de)multiplexer using an interleaved angled multimode interferometer on the silicon-on-insulator platform
A low-cost and high-performance wavelength division (de)multiplexing structure in the mid-IR wavelength range is demonstrated on the silicon-on-insulator platform using an interleaved angled multimode interferometer (AMMI). As compared to a single AMMI, the channel count was doubled and the channel spacing halved with negligible extra insertion loss and crosstalk and with only a slight increase in device footprint. The device requires only single lithography and etching steps for fabrication. Potential is also shown for achieving improved performance with further optimized design.
- 29 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 26 (7) , 714-717
50 Gb/s Silicon Photonics Receiver With Low Insertion Loss
Optical (de)multiplexers that can provide low insertion loss, low crosstalk, high thermal stability, and insensitivity to fabrication tolerances are essential components for silicon photonics integration. In this letter, we demonstrate the integration of an angled multimode interferometer coarse wavelength division multiplexer with germanium p-i-n photodetectors to form a 50 Gb/s receiver with a low insertion loss of <;-0.5 dB and crosstalk of <;-15 dB. The angled multimode interferometer has the flexibility to be designed on a platform with a wide range of waveguide thicknesses with little variation in performance, which allows for the optimization of other optical components in the photonics integrated circuit.
- 29 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 26 (7) , 714-717
50 Gb/s Silicon Photonics Receiver With Low Insertion Loss
Optical (de)multiplexers that can provide low insertion loss, low crosstalk, high thermal stability, and insensitivity to fabrication tolerances are essential components for silicon photonics integration. In this letter, we demonstrate the integration of an angled multimode interferometer coarse wavelength division multiplexer with germanium p-i-n photodetectors to form a 50 Gb/s receiver with a low insertion loss of <;-0.5 dB and crosstalk of <;-15 dB. The angled multimode interferometer has the flexibility to be designed on a platform with a wide range of waveguide thicknesses with little variation in performance, which allows for the optimization of other optical components in the photonics integrated circuit.
- 24 June 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (25) , 251116
Coarse wavelength division (de)multiplexer using an interleaved angled multimode interferometer structure
We have demonstrated a coarse wavelength (de)multiplexing structure on the silicon-on-insulator platform. It comprises two 4-channel angled multimode interferometers interleaved with an imbalanced Mach-Zehnder interferometer (MZI) leading to an 8-channel multiplexing device. The device requires only single lithography and etching steps for fabrication and has a good tolerance to fabrication errors in terms of waveguide width. The insertion loss and crosstalk achieved are 3-4 dB and –(15–20) dB, respectively. Potential is shown for achieving improved performance using larger waveguide bending radii in the MZI arms and/or (a) local heater(s) for refractive index tuning.
- 24 June 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (25) , 251116
Coarse wavelength division (de)multiplexer using an interleaved angled multimode interferometer structure
We have demonstrated a coarse wavelength (de)multiplexing structure on the silicon-on-insulator platform. It comprises two 4-channel angled multimode interferometers interleaved with an imbalanced Mach-Zehnder interferometer (MZI) leading to an 8-channel multiplexing device. The device requires only single lithography and etching steps for fabrication and has a good tolerance to fabrication errors in terms of waveguide width. The insertion loss and crosstalk achieved are 3-4 dB and –(15–20) dB, respectively. Potential is shown for achieving improved performance using larger waveguide bending radii in the MZI arms and/or (a) local heater(s) for refractive index tuning.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7606
Athermal and low loss ridge silicon waveguides
In this paper, we investigate athermal and low propagation loss silicon-on-insulator (SOI) rib waveguides. Propagation losses have been modeled for different dimensions of ridge waveguides achieving good agreement with experimental measurements. At certain waveguide widths, it is possible to obtain low propagation losses for both TE (transverse electric) and TM (transverse magnetic) modes. Racetrack ring resonator structures based on ridge waveguides covered by a polymer have been fabricated, aiming for an athermal design and therefore, a very small temperature dependent wavelength shift. Design guidelines for temperature insensitive and small propagation loss ridge waveguides are presented in this paper together with experimental data.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7606
Athermal and low loss ridge silicon waveguides
In this paper, we investigate athermal and low propagation loss silicon-on-insulator (SOI) rib waveguides. Propagation losses have been modeled for different dimensions of ridge waveguides achieving good agreement with experimental measurements. At certain waveguide widths, it is possible to obtain low propagation losses for both TE (transverse electric) and TM (transverse magnetic) modes. Racetrack ring resonator structures based on ridge waveguides covered by a polymer have been fabricated, aiming for an athermal design and therefore, a very small temperature dependent wavelength shift. Design guidelines for temperature insensitive and small propagation loss ridge waveguides are presented in this paper together with experimental data.