Grzegorz Trzciński
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Grzegorz Trzciński has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Łukasz Tymendorf
Independent Researcher, 12-100 Szczytno, Poland
8 shared publications - Tadeusz Moskalik
Department of Forest Utilization, Geomatics and Spatial Management, Institute of Forest Sciences, Warsaw University of Life Sciences (SGGW), Nowoursynowska 159, 02-776 Warszawa, Poland
5 shared publications - Paweł Kozakiewicz
Department of Wood Science and Wood Preservation, Institute of Wood Science and Furniture, Warsaw University of Life Sciences, Nowoursynowska 159, 02-776 Warsaw, Poland
4 shared publications - Alejandro Olivera
University of the Republic Uruguay, Tacuarembó University Centre
1 shared publication - Allan Bradley
FPInnovations
1 shared publication - Andis Lazdins
Latvian State Forest Research Institute ‘Silava’, 2169 Salaspils, Latvia
1 shared publication
Latest Publications
- Open Access
Impact of Forest Operations Planning on Greenhouse Gas Emissions
This study investigates how key planning variables—the number of wood assortments, the geometric shape of clear-cut areas, and the extraction (forwarding) distance—influence greenhouse gas (GHG) emissions. Twelve plots formed a heterogeneous sample with similar site type and soil moisture conditions. A Komatsu 931 harvester and a 855 forwarder, driven by the experienced operators, were used to ensure consistency in operator skill. For each plot, the isoperimetric quotient was computed to quantify how plot shape correlated with labor hours, fuel consumption, and the resulting volume of GHG emitted. The number of assortments extracted per plot ranged from three to fourteen product groups. The results show that plots with more complex shapes require significantly more operator time and fuel. Increasing the number of assortments amplifies handling time and fuel use. Longer extraction distances further exacerbate the emissions. These findings underscore the importance of integrating spatial geometry and wood assortment planning into harvest scheduling to enhance productivity and reduce the carbon footprint of forest operations. Recommendations for practitioners include prioritizing more compact treatment units, optimizing assortment grouping, and minimizing extraction distances as key strategies for precision forestry.
Open AccessImpact of Forest Operations Planning on Greenhouse Gas Emissions
This study investigates how key planning variables—the number of wood assortments, the geometric shape of clear-cut areas, and the extraction (forwarding) distance—influence greenhouse gas (GHG) emissions. Twelve plots formed a heterogeneous sample with similar site type and soil moisture conditions. A Komatsu 931 harvester and a 855 forwarder, driven by the experienced operators, were used to ensure consistency in operator skill. For each plot, the isoperimetric quotient was computed to quantify how plot shape correlated with labor hours, fuel consumption, and the resulting volume of GHG emitted. The number of assortments extracted per plot ranged from three to fourteen product groups. The results show that plots with more complex shapes require significantly more operator time and fuel. Increasing the number of assortments amplifies handling time and fuel use. Longer extraction distances further exacerbate the emissions. These findings underscore the importance of integrating spatial geometry and wood assortment planning into harvest scheduling to enhance productivity and reduce the carbon footprint of forest operations. Recommendations for practitioners include prioritizing more compact treatment units, optimizing assortment grouping, and minimizing extraction distances as key strategies for precision forestry.
- Open Access
Parameters of Medium-Size Wood Deliveries Depending on the Season, Moisture Content and Assortment of the Load
In the years 2022 to 2023, the harvesting of medium-sized round wood by the State Forests Service in Poland was estimated at between 22.2 and 23.6 million solid cubic meters per year. This is a significant amount of timber to be transported by road. It is a challenge for both transport companies and round wood buyers. The high variability of wood density depending on the species in combination with its moisture content is a significant issue in logistics operations. This study focuses on the influence of the absolute moisture content on selected parameters of wood deliveries, taking into account the differences in the seasons. The total weight of a transport set (GVW) and empty set (Tare) and the weight of the load (Net) were determined on the basis of weighing the transports on stationary scales at the recipient. The moisture content of each wood load was determined using the dryer-weigher method for sawdust taken from the cutting of several logs from the delivery. This study analyzed a total of 13,602 transports of ten tree species and two wood assortments of pulpwood (S2a) and industrial wood (S2ap) in four seasons in the years 2020–2022. Pine was the dominant species in 5352 deliveries, and spruce was the dominant species in 3161. In terms of seasons, 3983 transports were recorded in the summer, 3650 were recorded in the spring, and 3492 were recorded in the autumn. The lowest number of 2475 was in winter. The mean volume of delivered wood (from 13,602 transports) was 28.18 m3, with a range of results from 19.00 to 51.29 m3 and SD = 2.40. The mean weight of the shipment was 24.95 Mg, with SD = 3.36. The range was from 13.92 Mg to 38.20 Mg. The mean absolute moisture content (AMC) of all wood loads (regardless of species and quality) was 42.91%. The results varied significantly (SD = 6.41). The minimum value was 15.64%, and the maximum value was 66.79%. The absolute moisture content of round wood is related to the season, species and assortment of transported wood. Loads of hardwood have lower average solid cubic meter values than softwood.
Open AccessParameters of Medium-Size Wood Deliveries Depending on the Season, Moisture Content and Assortment of the Load
In the years 2022 to 2023, the harvesting of medium-sized round wood by the State Forests Service in Poland was estimated at between 22.2 and 23.6 million solid cubic meters per year. This is a significant amount of timber to be transported by road. It is a challenge for both transport companies and round wood buyers. The high variability of wood density depending on the species in combination with its moisture content is a significant issue in logistics operations. This study focuses on the influence of the absolute moisture content on selected parameters of wood deliveries, taking into account the differences in the seasons. The total weight of a transport set (GVW) and empty set (Tare) and the weight of the load (Net) were determined on the basis of weighing the transports on stationary scales at the recipient. The moisture content of each wood load was determined using the dryer-weigher method for sawdust taken from the cutting of several logs from the delivery. This study analyzed a total of 13,602 transports of ten tree species and two wood assortments of pulpwood (S2a) and industrial wood (S2ap) in four seasons in the years 2020–2022. Pine was the dominant species in 5352 deliveries, and spruce was the dominant species in 3161. In terms of seasons, 3983 transports were recorded in the summer, 3650 were recorded in the spring, and 3492 were recorded in the autumn. The lowest number of 2475 was in winter. The mean volume of delivered wood (from 13,602 transports) was 28.18 m3, with a range of results from 19.00 to 51.29 m3 and SD = 2.40. The mean weight of the shipment was 24.95 Mg, with SD = 3.36. The range was from 13.92 Mg to 38.20 Mg. The mean absolute moisture content (AMC) of all wood loads (regardless of species and quality) was 42.91%. The results varied significantly (SD = 6.41). The minimum value was 15.64%, and the maximum value was 66.79%. The absolute moisture content of round wood is related to the season, species and assortment of transported wood. Loads of hardwood have lower average solid cubic meter values than softwood.
- Open Access
- 10 November 2023
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Croatian journal of forest engineering
- Vol. 45 (1) , 217-236
Overview of Global Long-Distance Road Transportation of Industrial Roundwood
The aim of the study was to provide a comprehensive overview of global long-distance road transportation of industrial roundwood. The study focused on the maximum gross vehicle weight (GVW) limits allowed with different timber truck configurations, typical payloads in timber trucking, the road transportation share of the total industrial roundwood long-distance transportation volume, and the average long-distance transportation distances and costs of industrial roundwood. The study was carried out as a questionnaire survey. The questionnaire was sent to timber transportation logistics experts and research scientists in the 30 countries with the largest industrial roundwood removals in Europe, as well as selected major forestry countries in the world (Argentina, Australia, Brazil, Canada, Chile, China, Japan, New Zealand, South Africa, Türkiye, the United States of America and Uruguay) in February 2022, and closed in May 2022. A total of 31 countries took part in the survey. The survey illustrated that timber trucking was the main long-distance transportation method of industrial roundwood in almost every country surveyed. Road transportation averaged 89% of the total industrial roundwood long-distance transportation volume. Timber truck configurations of 4 to 9 axles with GVW limits of around 30 tonnes to over 70 tonnes were most commonly used. The results indicated that higher GVW limits allowed significantly higher payloads in timber trucking, with the lowest payloads at less than 25 tonnes, and the highest payloads more than 45 tonnes. The average road transportation distance with industrial roundwood was 128 km, and the average long-distance transportation cost in timber trucking was €11.1 per tonne of timber transported. In the entire survey material, there was a direct relationship between transportation distance and transportation costs and an inverse relationship between maximum GVW limits and transportation costs. Consequently, in order to reduce transportation costs, it is essential to maximise payloads (within legal limits) and minimise haul distances. Several measures to increase cost- and energy-efficiency, and to reduce greenhouse gas emissions in road transportation logistics, are discussed in the paper. On the basis of the survey, it is recommended that up-to-date statistical data and novel research studies on the long-distance transportation of industrial roundwood be conducted in some countries in the future.
- 10 November 2023
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Croatian journal of forest engineering
- Vol. 45 (1) , 217-236
Open AccessOverview of Global Long-Distance Road Transportation of Industrial Roundwood
The aim of the study was to provide a comprehensive overview of global long-distance road transportation of industrial roundwood. The study focused on the maximum gross vehicle weight (GVW) limits allowed with different timber truck configurations, typical payloads in timber trucking, the road transportation share of the total industrial roundwood long-distance transportation volume, and the average long-distance transportation distances and costs of industrial roundwood. The study was carried out as a questionnaire survey. The questionnaire was sent to timber transportation logistics experts and research scientists in the 30 countries with the largest industrial roundwood removals in Europe, as well as selected major forestry countries in the world (Argentina, Australia, Brazil, Canada, Chile, China, Japan, New Zealand, South Africa, Türkiye, the United States of America and Uruguay) in February 2022, and closed in May 2022. A total of 31 countries took part in the survey. The survey illustrated that timber trucking was the main long-distance transportation method of industrial roundwood in almost every country surveyed. Road transportation averaged 89% of the total industrial roundwood long-distance transportation volume. Timber truck configurations of 4 to 9 axles with GVW limits of around 30 tonnes to over 70 tonnes were most commonly used. The results indicated that higher GVW limits allowed significantly higher payloads in timber trucking, with the lowest payloads at less than 25 tonnes, and the highest payloads more than 45 tonnes. The average road transportation distance with industrial roundwood was 128 km, and the average long-distance transportation cost in timber trucking was €11.1 per tonne of timber transported. In the entire survey material, there was a direct relationship between transportation distance and transportation costs and an inverse relationship between maximum GVW limits and transportation costs. Consequently, in order to reduce transportation costs, it is essential to maximise payloads (within legal limits) and minimise haul distances. Several measures to increase cost- and energy-efficiency, and to reduce greenhouse gas emissions in road transportation logistics, are discussed in the paper. On the basis of the survey, it is recommended that up-to-date statistical data and novel research studies on the long-distance transportation of industrial roundwood be conducted in some countries in the future.
- Open Access
- 30 June 2023
- Published by Adam Mickiewicz University Poznan in Ruch Prawniczy, Ekonomiczny i Socjologiczny
- Vol. 85 (2) , 127-141
Drogi wewnętrzne i gruntowe w postępowaniach administracyjnych i orzecznictwie sądowoadministracyjnym w sprawach budowlanych: problemy interpretacyjne
Regulacja problematyki dróg wewnętrznych w Polsce jest wciąż niewystarczająca, a na jej tle widoczne są liczne rozbieżności orzecznicze. Status tych dróg jest odmienny aniżeli dróg publicznych, przejawia się to w zakresie zarządzania tymi drogami, w tym ich remontami. Zagadnienie to jest istotne z punktu widzenia praktyki, ponieważ nierzadko drogi wewnętrzne w rzeczywistości pełnią funkcje dróg publicznych. Celem artykułu jest ukazanie, że drogi wewnętrzne stanowią istotne trakty komunikacyjne. Artykuł koncentruje się na funkcjonowaniu dróg wewnętrznych w aspektach prawnych i technicznych. W pierwszej kolejności przedstawiono problematykę definicjidróg, w tym dróg wewnętrznych w różnych aktach normatywnych. Szeroko omówiono problematykę pojęcia pasa drogowego w odniesieniu do prawa budowlanego, a szczególnie w klasyfikacji robót budowlanych – przebudowy drogi. Wskazano, jak orzecznictwo organów i sądów rozumie przebudowę drogi, remont drogi w kontekście dróg wewnętrznych. Kolejno rozważano, czy drogi wewnętrzne są obiektami budowlanymi, a także jakie warunki wówczas muszą zostać zrealizowane dla remontu czy przebudowy drogi. Następnie przedstawione zostało studium przypadków ukazujące różną interpretację prawa przez organy administracji, zwłaszcza przebudowy drogi leśnej jako drogi wewnętrznej. Na tle stanu faktycznego i analizy orzecznictwa autorzy stwierdzają, że niezbędne jest kompleksowe uregulowanie tej problematyki w celu uzyskania stabilności orzeczniczej i pewności prawa jego adresatów, będących właścicielami czy zarządcami tych dróg.
- 30 June 2023
- Published by Adam Mickiewicz University Poznan in Ruch Prawniczy, Ekonomiczny i Socjologiczny
- Vol. 85 (2) , 127-141
Open AccessDrogi wewnętrzne i gruntowe w postępowaniach administracyjnych i orzecznictwie sądowoadministracyjnym w sprawach budowlanych: problemy interpretacyjne
Regulacja problematyki dróg wewnętrznych w Polsce jest wciąż niewystarczająca, a na jej tle widoczne są liczne rozbieżności orzecznicze. Status tych dróg jest odmienny aniżeli dróg publicznych, przejawia się to w zakresie zarządzania tymi drogami, w tym ich remontami. Zagadnienie to jest istotne z punktu widzenia praktyki, ponieważ nierzadko drogi wewnętrzne w rzeczywistości pełnią funkcje dróg publicznych. Celem artykułu jest ukazanie, że drogi wewnętrzne stanowią istotne trakty komunikacyjne. Artykuł koncentruje się na funkcjonowaniu dróg wewnętrznych w aspektach prawnych i technicznych. W pierwszej kolejności przedstawiono problematykę definicjidróg, w tym dróg wewnętrznych w różnych aktach normatywnych. Szeroko omówiono problematykę pojęcia pasa drogowego w odniesieniu do prawa budowlanego, a szczególnie w klasyfikacji robót budowlanych – przebudowy drogi. Wskazano, jak orzecznictwo organów i sądów rozumie przebudowę drogi, remont drogi w kontekście dróg wewnętrznych. Kolejno rozważano, czy drogi wewnętrzne są obiektami budowlanymi, a także jakie warunki wówczas muszą zostać zrealizowane dla remontu czy przebudowy drogi. Następnie przedstawione zostało studium przypadków ukazujące różną interpretację prawa przez organy administracji, zwłaszcza przebudowy drogi leśnej jako drogi wewnętrznej. Na tle stanu faktycznego i analizy orzecznictwa autorzy stwierdzają, że niezbędne jest kompleksowe uregulowanie tej problematyki w celu uzyskania stabilności orzeczniczej i pewności prawa jego adresatów, będących właścicielami czy zarządcami tych dróg.
- Open Access
Multifactorial Analysis of the Axle Load of Truck Sets during the Transport of Sawmill By-Products
The aim of the study was to investigate the actual axle loads of vehicles used for the transport of sawmill by-products, resulting from the total weight of the transport set (GVW) at different times of the year and depending on the type of sets and transported assortment. Sawmill by-product loads were divided into groups: wood chips, sawdust, slabs and recycled wood. The research was carried out at the recipient of the sawmill by-products as well as at the producer. The GVW was determined on the basis of weighing the entire set on a stationary scale at the premises of the companies. The load on the individual axles of high tonnage truck units was measured using Model DINI ARGEO WWSD portable truck scales with a 3590M309 weighing terminal. Almost 230 transports were analyzed. It was shown that the average GVW is 39.25 t for transport sets with a load of 22.44 t of sawmill by-products with the usage of the semi-trailer capacity of 0.85. For all transport sets, the average load on the individual axles range from 6.72 t (axle 5 in a six-axle truck and trailer-TT) to 10.29 t for axle 2 in a truck and semi-trailer (TST), where the highest occurs on axle 2 of the truck (drive axle). The influence of the type of transport set (TST or TT) and the type of the assortments on the axle load is shown, and the existing correlations are at the level of 0.604–0.669 for axles 3–5 in the TST set. The static axle loads of the transport sets for the sawmill by-products and the distribution of the total weight of the set among the axles are different from those for roundwood transport.
Open AccessMultifactorial Analysis of the Axle Load of Truck Sets during the Transport of Sawmill By-Products
The aim of the study was to investigate the actual axle loads of vehicles used for the transport of sawmill by-products, resulting from the total weight of the transport set (GVW) at different times of the year and depending on the type of sets and transported assortment. Sawmill by-product loads were divided into groups: wood chips, sawdust, slabs and recycled wood. The research was carried out at the recipient of the sawmill by-products as well as at the producer. The GVW was determined on the basis of weighing the entire set on a stationary scale at the premises of the companies. The load on the individual axles of high tonnage truck units was measured using Model DINI ARGEO WWSD portable truck scales with a 3590M309 weighing terminal. Almost 230 transports were analyzed. It was shown that the average GVW is 39.25 t for transport sets with a load of 22.44 t of sawmill by-products with the usage of the semi-trailer capacity of 0.85. For all transport sets, the average load on the individual axles range from 6.72 t (axle 5 in a six-axle truck and trailer-TT) to 10.29 t for axle 2 in a truck and semi-trailer (TST), where the highest occurs on axle 2 of the truck (drive axle). The influence of the type of transport set (TST or TT) and the type of the assortments on the axle load is shown, and the existing correlations are at the level of 0.604–0.669 for axles 3–5 in the TST set. The static axle loads of the transport sets for the sawmill by-products and the distribution of the total weight of the set among the axles are different from those for roundwood transport.
- Open Access
Bearing Capacity of Forest Roads on Poor-Bearing Road Subgrades following Six Years of Use
The research was conducted on a forest road on the territory of the State Forests in Poland, in the Brzeziny Forest District, where eight test sections with a total length of 422 m were created with different pavement system on a low-bearing soil substrate (clay, silt loam) as part of the road reconstruction in 2016. The bearing capacity of the pavement was evaluated based on the static strain modulus ME MN·m−2 by measuring with a statistic plate (VSS), the dynamic deformation modulus Evd MN·m−2 obtained from lightweight deflectometer measurements, and the elastic deflection of the pavement Us mm evaluated from Benkelaman beam measurements. It has been shown that pavements made of crushed aggregate and common gravel on timber roller substructure maintain good bearing capacity parameters, where the average values of secondary modulus of strain are above 130 MN·m−2, and in the case of pine rollers, this modulus has increased. Pavements on low-bearing soils reinforced with willow brushwood mattresses have low bearing capacity parameters, with averages of 26.09 ≤ MEII ≤ 53.93 and 22.1 ≤ Evd ≤ 39.1 MN·m−2, but the technical condition of the pavement makes it possible to continue carrying out forestry-related transportation. The research confirms the possibility of reinforcing soils with poor bearing capacity with wooden rollers, and in the case of willow mats for roads with light truck movements.
Open AccessBearing Capacity of Forest Roads on Poor-Bearing Road Subgrades following Six Years of Use
The research was conducted on a forest road on the territory of the State Forests in Poland, in the Brzeziny Forest District, where eight test sections with a total length of 422 m were created with different pavement system on a low-bearing soil substrate (clay, silt loam) as part of the road reconstruction in 2016. The bearing capacity of the pavement was evaluated based on the static strain modulus ME MN·m−2 by measuring with a statistic plate (VSS), the dynamic deformation modulus Evd MN·m−2 obtained from lightweight deflectometer measurements, and the elastic deflection of the pavement Us mm evaluated from Benkelaman beam measurements. It has been shown that pavements made of crushed aggregate and common gravel on timber roller substructure maintain good bearing capacity parameters, where the average values of secondary modulus of strain are above 130 MN·m−2, and in the case of pine rollers, this modulus has increased. Pavements on low-bearing soils reinforced with willow brushwood mattresses have low bearing capacity parameters, with averages of 26.09 ≤ MEII ≤ 53.93 and 22.1 ≤ Evd ≤ 39.1 MN·m−2, but the technical condition of the pavement makes it possible to continue carrying out forestry-related transportation. The research confirms the possibility of reinforcing soils with poor bearing capacity with wooden rollers, and in the case of willow mats for roads with light truck movements.
- Open Access
- 15 October 2022
- Published by MDPI AG in Environmental Sciences Proceedings
- Vol. 22 (1) , 12
Axle Load of Round Wood Transport Vehicles in Relation to Wood Assortment
The variety of wood loads and their parameters (humidity, density, assortment) are often the cause of the increased total weight of the vehicle (GVW). With significant GVW exceeding, forest roads are exposed to high-tonnage vehicles, which results in vehicle axle loads above the accepted design parameters for the pavement. The purpose of this study was to investigate the real axle loads of round wood transport vehicles arising from the gross vehicle weight (GVW) of the transport set in different seasons of the year and depending on the type of transport set and the type of wood assortments. Measurements of axle loads for round wood truck transport sets were carried out on the sites of three large wood industry companies from the north of Poland, which process different types of wood. The load on the individual axles of the high tonnage truck units was measured using model DINI ARGEO WWSD portable truck scales with a 3590M309 weighing terminal with 0.01 t graduation. In total, measurements were taken for 904 round wood deliveries made by different transport sets: a truck and trailer set with 473 deliveries, including 344 deliveries by six-axle sets, a truck, and semi-trailer with 334 deliveries, where 193 were made by six-axle sets. The lowest axle load for all the sets occurred on axle one in the range of average values 7.07–7.86 t with a spread of results from 4.49 to 10.20 t. The highest average axle loads of 9.15–12.43 t was found on the axle for all the observed transport sets, where a maximum value of 14.52 t was also found. There were statistically significant differences in the values of the loads on individual axles depending on the type of truck set and type of wood assortment. Comparative analysis by the Kruskal–Wallis test of all axle load results depending on the vehicle types and number of axles, showed statistically significant differences. When analyzing the axle loads in five-axle sets with respect to the delivery date, statistically significant differences were found for all the axles. These differences occurred mainly for measurements performed in the summer and other seasons, the most visible of which were on the second and third axle. The loads of transported wood (assortments) also influenced the resulting axle loads, which was confirmed by statistical analysis. For most axles, there are differences in the axle loads for sets with MS (medium-size, industrial wood) deliveries and other assortments. Additionally, on axles 4–5, there are differences between Ls (large-size) deliveries and other deliveries (multiple mean rank test). In the case of TS transport sets, there is no big difference between the axle loads, only in the case of short assortment Ms where the second and third axles have higher average axle loads of just over 10 t. In the truck and trailer combinations (TT), the highest average axle loads are on the fourth and fifth axle in the range 8.5–12.0 t, with lower values for shorter 3.7 m and Ms grades. The distribution of the total gross vehicle weight of the set is, on average, 58–60% to the truck (three axles) and 40–42% to the trailer/semi-trailer (two axles) in five-axle sets and in six-axle sets, the truck and trailer/semi-trailer (three axles).
- 15 October 2022
- Published by MDPI AG in Environmental Sciences Proceedings
- Vol. 22 (1) , 12
Open AccessAxle Load of Round Wood Transport Vehicles in Relation to Wood Assortment
The variety of wood loads and their parameters (humidity, density, assortment) are often the cause of the increased total weight of the vehicle (GVW). With significant GVW exceeding, forest roads are exposed to high-tonnage vehicles, which results in vehicle axle loads above the accepted design parameters for the pavement. The purpose of this study was to investigate the real axle loads of round wood transport vehicles arising from the gross vehicle weight (GVW) of the transport set in different seasons of the year and depending on the type of transport set and the type of wood assortments. Measurements of axle loads for round wood truck transport sets were carried out on the sites of three large wood industry companies from the north of Poland, which process different types of wood. The load on the individual axles of the high tonnage truck units was measured using model DINI ARGEO WWSD portable truck scales with a 3590M309 weighing terminal with 0.01 t graduation. In total, measurements were taken for 904 round wood deliveries made by different transport sets: a truck and trailer set with 473 deliveries, including 344 deliveries by six-axle sets, a truck, and semi-trailer with 334 deliveries, where 193 were made by six-axle sets. The lowest axle load for all the sets occurred on axle one in the range of average values 7.07–7.86 t with a spread of results from 4.49 to 10.20 t. The highest average axle loads of 9.15–12.43 t was found on the axle for all the observed transport sets, where a maximum value of 14.52 t was also found. There were statistically significant differences in the values of the loads on individual axles depending on the type of truck set and type of wood assortment. Comparative analysis by the Kruskal–Wallis test of all axle load results depending on the vehicle types and number of axles, showed statistically significant differences. When analyzing the axle loads in five-axle sets with respect to the delivery date, statistically significant differences were found for all the axles. These differences occurred mainly for measurements performed in the summer and other seasons, the most visible of which were on the second and third axle. The loads of transported wood (assortments) also influenced the resulting axle loads, which was confirmed by statistical analysis. For most axles, there are differences in the axle loads for sets with MS (medium-size, industrial wood) deliveries and other assortments. Additionally, on axles 4–5, there are differences between Ls (large-size) deliveries and other deliveries (multiple mean rank test). In the case of TS transport sets, there is no big difference between the axle loads, only in the case of short assortment Ms where the second and third axles have higher average axle loads of just over 10 t. In the truck and trailer combinations (TT), the highest average axle loads are on the fourth and fifth axle in the range 8.5–12.0 t, with lower values for shorter 3.7 m and Ms grades. The distribution of the total gross vehicle weight of the set is, on average, 58–60% to the truck (three axles) and 40–42% to the trailer/semi-trailer (two axles) in five-axle sets and in six-axle sets, the truck and trailer/semi-trailer (three axles).
- Open Access
Methods of Wood Volume Determining and Its Implications for Forest Transport
Proper measurements are extremely significant for the forest owner, the harvesting company, the hauler, the final buyer, and the wood processing company. The accuracy of round wood volume determination is of fundamental importance in planning and accounting for individual processes related to the wood trade. It is the basis for determining the maximum quantity in single load of wood that allows for using the permissible total gross vehicle weight. The determination of wood load in cubic meters does not allow unequivocally determining its weight, which often leads to overloading of vehicles. This paper presents a comparison of the photo-optical method for determining the volume of wood to be transported with the real measurement and determination of the weight of a load and the total gross vehicle weight (GVW) with the simultaneous application of conversion factors determining the weight of the load from the volume of wood. The measurement included 23 broadleaf round wood piles (193.73 m3) and 14 coniferous round wood piles (149.23 m3). The measurement error for broadleaf wood piles ranges from −47.67% to 63.16%, and from −43.31% to 24.72% for coniferous wood piles. Determination of the volume of a broadleaf wood pile using the iFOVEA method had an average error of 1.34%, while the Timbeter method had an average error of −1.83%. In the coniferous wood pile measurement, the error is −12.82% and 2.41%, respectively. Verification of the volume of the large-sized wood indicated on the delivery note (reference value) on the log sorting line (by laser scanning) showed larger volumes by 0.10 m3 to 2.54 m3, giving a percentage error of 0.35% and 8.62%, respectively. As a consequence of the application of such methods for determining the weight of wood loads, the transport truck sets are often significantly overloaded, which has a significant impact on the accelerated degradation of roads and safety in traffic and timber transportation.
Open AccessMethods of Wood Volume Determining and Its Implications for Forest Transport
Proper measurements are extremely significant for the forest owner, the harvesting company, the hauler, the final buyer, and the wood processing company. The accuracy of round wood volume determination is of fundamental importance in planning and accounting for individual processes related to the wood trade. It is the basis for determining the maximum quantity in single load of wood that allows for using the permissible total gross vehicle weight. The determination of wood load in cubic meters does not allow unequivocally determining its weight, which often leads to overloading of vehicles. This paper presents a comparison of the photo-optical method for determining the volume of wood to be transported with the real measurement and determination of the weight of a load and the total gross vehicle weight (GVW) with the simultaneous application of conversion factors determining the weight of the load from the volume of wood. The measurement included 23 broadleaf round wood piles (193.73 m3) and 14 coniferous round wood piles (149.23 m3). The measurement error for broadleaf wood piles ranges from −47.67% to 63.16%, and from −43.31% to 24.72% for coniferous wood piles. Determination of the volume of a broadleaf wood pile using the iFOVEA method had an average error of 1.34%, while the Timbeter method had an average error of −1.83%. In the coniferous wood pile measurement, the error is −12.82% and 2.41%, respectively. Verification of the volume of the large-sized wood indicated on the delivery note (reference value) on the log sorting line (by laser scanning) showed larger volumes by 0.10 m3 to 2.54 m3, giving a percentage error of 0.35% and 8.62%, respectively. As a consequence of the application of such methods for determining the weight of wood loads, the transport truck sets are often significantly overloaded, which has a significant impact on the accelerated degradation of roads and safety in traffic and timber transportation.
- Open Access
Importance of the Moisture Content of Large-Sized Scots Pine (Pinus sylvestris L.) Roundwood in Its Road Transport
Scots pine (Pinus sylvestris L.) is one of the most important forest tree species in Europe, and its wood is a main raw material in the wood industry of many countries of the region. The high variability of pine wood density in connection with its moisture content is a challenge in transport operations. An important part of the roundwood transport of pine wood by trucks is the transport of large-size roundwood (sawlogs). As part of the research, an analysis was carried out of the influence of absolute wood moisture content, determined in various ways, on selected truck transport parameters of large-size pine wood. The analyses of the supply of wood to a large sawmill in northern Poland took into account different seasons. The results indicate that the average moisture content of the transported pine wood is at a level of approximately 95% (determined by dry weight) and the density at 0.878 Mg m−3 (determined using the stereometric method). Quick measurement with the use of a resistance hygrometer gives significantly lower results both on the side surface and on the cross-cut end of the log. Regardless of the method of measurement, the absolute moisture content of wood in loads depends on the date of delivery (season), which is reflected in the variability of the density and weight of the loads. The indicated strong correlations between the selected, tested characteristics of roundwood transports are important for forestry practice too. It is the possibility of using the methods of quick determination of fresh wood moisture to estimate the density of wood and to predict and determine the mass of the load.
Open AccessImportance of the Moisture Content of Large-Sized Scots Pine (Pinus sylvestris L.) Roundwood in Its Road Transport
Scots pine (Pinus sylvestris L.) is one of the most important forest tree species in Europe, and its wood is a main raw material in the wood industry of many countries of the region. The high variability of pine wood density in connection with its moisture content is a challenge in transport operations. An important part of the roundwood transport of pine wood by trucks is the transport of large-size roundwood (sawlogs). As part of the research, an analysis was carried out of the influence of absolute wood moisture content, determined in various ways, on selected truck transport parameters of large-size pine wood. The analyses of the supply of wood to a large sawmill in northern Poland took into account different seasons. The results indicate that the average moisture content of the transported pine wood is at a level of approximately 95% (determined by dry weight) and the density at 0.878 Mg m−3 (determined using the stereometric method). Quick measurement with the use of a resistance hygrometer gives significantly lower results both on the side surface and on the cross-cut end of the log. Regardless of the method of measurement, the absolute moisture content of wood in loads depends on the date of delivery (season), which is reflected in the variability of the density and weight of the loads. The indicated strong correlations between the selected, tested characteristics of roundwood transports are important for forestry practice too. It is the possibility of using the methods of quick determination of fresh wood moisture to estimate the density of wood and to predict and determine the mass of the load.
- Open Access
Parameters of Trucks and Loads in the Transport of Scots Pine Wood Biomass Depending on the Season and Moisture Content of the Load
Transport of wood biomass is one of the key operations in forestry and in the wood industry. An important part is the transport of shredded wood, where the most common forms are chips and sawdust. The aim of the research was to present the variability of the total weight of trucks (gross vehicle weight, GVW), the weight of the empty trucks (tare), and loads of chips and sawdust in different periods of the year. Changes in specific parameters were analyzed: GVW; tare weight; trailer capacity; use of the trailer load capacity; bulk volume and bulk density of wood biomass loads; solid cubic meter (m3) and weight of 1m3 of the load; and load weight depending on the season, with simultaneous measurements of wood chips and sawdust moisture. More than 250 transports from four seasons of the year were analyzed in the research. It was found that the total weight of trucks (GVW) was at a comparable level, on average from 39.42 to 39.64 Mg with slight differences (with SD 0.29 and 0.39). The weight of empty trucks was 16.15 Mg for chip-bearing trucks and 15.93 Mg for sawdust-bearing trucks (with SD 0.604 and 0.526). The type of wood material has an influence on the transported volume. The average quantity of load in the bulk cubic meter was 64.783 m3 for wood chips (SD 3.127) and 70.465 m3 (SD 2.516) for sawdust. Over 30% differences in the volume of transported wood chips and approximately 18% for sawdust were observed. The use of the loading capacity of the trailer was on average 72.58% (SD 5.567) for the transport of wood chips and 77.42% (SD 3.019) for the transport of sawdust. The sawdust bulk density was from 0.3050 to 0.4265 Mg⋅m−3 for wood chips and 0.3200 to 0.3556 Mg⋅m−3 for sawdust. This parameter is significantly dependent on moisture content, and the determined correlation functions can be used for estimating and predicting bulk density. The abovementioned absolute moisture content of chips and sawdust also depends on the season, which also affects the selected parameters of wood biomass loads.
Open AccessParameters of Trucks and Loads in the Transport of Scots Pine Wood Biomass Depending on the Season and Moisture Content of the Load
Transport of wood biomass is one of the key operations in forestry and in the wood industry. An important part is the transport of shredded wood, where the most common forms are chips and sawdust. The aim of the research was to present the variability of the total weight of trucks (gross vehicle weight, GVW), the weight of the empty trucks (tare), and loads of chips and sawdust in different periods of the year. Changes in specific parameters were analyzed: GVW; tare weight; trailer capacity; use of the trailer load capacity; bulk volume and bulk density of wood biomass loads; solid cubic meter (m3) and weight of 1m3 of the load; and load weight depending on the season, with simultaneous measurements of wood chips and sawdust moisture. More than 250 transports from four seasons of the year were analyzed in the research. It was found that the total weight of trucks (GVW) was at a comparable level, on average from 39.42 to 39.64 Mg with slight differences (with SD 0.29 and 0.39). The weight of empty trucks was 16.15 Mg for chip-bearing trucks and 15.93 Mg for sawdust-bearing trucks (with SD 0.604 and 0.526). The type of wood material has an influence on the transported volume. The average quantity of load in the bulk cubic meter was 64.783 m3 for wood chips (SD 3.127) and 70.465 m3 (SD 2.516) for sawdust. Over 30% differences in the volume of transported wood chips and approximately 18% for sawdust were observed. The use of the loading capacity of the trailer was on average 72.58% (SD 5.567) for the transport of wood chips and 77.42% (SD 3.019) for the transport of sawdust. The sawdust bulk density was from 0.3050 to 0.4265 Mg⋅m−3 for wood chips and 0.3200 to 0.3556 Mg⋅m−3 for sawdust. This parameter is significantly dependent on moisture content, and the determined correlation functions can be used for estimating and predicting bulk density. The abovementioned absolute moisture content of chips and sawdust also depends on the season, which also affects the selected parameters of wood biomass loads.