Yin Fong Yeong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yin Fong Yeong has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Kok Keong Lau
Center of Carbon Capture, Utilisation and Storage (CCCUS), Department of Chemical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia
10 shared publications - Azmi Mohd Shariff
Universiti Teknologi PETRONAS
7 shared publications Li Sze Lai
Universiti Teknologi PETRONAS Department of Chemical Engineering Bandar Seri Iskandar 32610 Perak Malaysia
7 shared publicationsMohd Shariff Azmi
Universiti Teknologi PETRONAS
3 shared publicationsNorwahyu Jusoh
Chemical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia
3 shared publicationsKok Keong Lau
Universiti Teknologi PETRONAS
2 shared publications
Latest Publications
- 3 April 2017
- Published by Wiley in Chemical Engineering & Technology
- Vol. 40 (6) , 1031-1042
Single and Binary CO2/CH4 Separation of a Zeolitic Imidazolate Framework‐8 Membrane
- 3 April 2017
- Published by Wiley in Chemical Engineering & Technology
- Vol. 40 (6) , 1031-1042
Single and Binary CO2/CH4 Separation of a Zeolitic Imidazolate Framework‐8 Membrane
- 1 January 2017
- Published by Elsevier in Ultrasonics Sonochemistry
- Vol. 34, 273-280
Rapid-synthesis of zeolite T via sonochemical-assisted hydrothermal growth method
- 1 January 2017
- Published by Elsevier in Ultrasonics Sonochemistry
- Vol. 34, 273-280
Rapid-synthesis of zeolite T via sonochemical-assisted hydrothermal growth method
- 10 May 2016
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (2) , 420-431
Synthesis of zeolitic imidazolate frameworks (ZIF)‐8 membrane and its process optimization study in separation ofCO2from natural gas
BACKGROUND: In this work, well‐intergrown zeolitic imidazolate frameworks‐8 (ZIF‐8) membrane was synthesized through a microwave‐assisted secondary solvothermal growth method. A solvent evaporation seeding method was applied prior to membrane growth. Subsequently, process optimization for the separation ofCO2from natural gas through theZIF‐8 membrane was studied using response surface methodology. The process variables studied includedCO2feed composition (36–83%), total pressure difference (100–700kPa) and temperature (303–343 K). Three empirical models were generated using a central composite design in order to study the interaction between the process variables and the responses, includingCO2permeance,CH4permeance andCO2/CH4separation factor. The optimum condition was then determined for maximumCO2permeance andCO2/CH4separation factor and minimumCH4permeance.RESULTS: Using this method,ZIF‐8 seeds of nano‐size were well distributed on the support due to high nucleation rate at the supersaturation condition. The presence of heavy hydrocarbons affectedCH4permeance, attributed to the molar mass and viscosity. An optimumCO2permeance of 2.76 × 10−8mol m−2s−1Pa−1andCO2/CH4separation factor of 3.72 was obtained at 312 K, 100kPaand 36%CO2feed composition. The experimental results were in agreement with the predicted values with an average error lower than ± 7%.CONCLUSION: SelectiveZIF‐8 membrane was successfully synthesized using a feasible and reproducible solvent evaporation seeding method. The experimental data for the optimum condition were in good agreement with the predicted data, showing the accuracy of the empirical models. © 2016 Society of Chemical Industry
- 10 May 2016
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (2) , 420-431
Synthesis of zeolitic imidazolate frameworks (ZIF)‐8 membrane and its process optimization study in separation ofCO2from natural gas
BACKGROUND: In this work, well‐intergrown zeolitic imidazolate frameworks‐8 (ZIF‐8) membrane was synthesized through a microwave‐assisted secondary solvothermal growth method. A solvent evaporation seeding method was applied prior to membrane growth. Subsequently, process optimization for the separation ofCO2from natural gas through theZIF‐8 membrane was studied using response surface methodology. The process variables studied includedCO2feed composition (36–83%), total pressure difference (100–700kPa) and temperature (303–343 K). Three empirical models were generated using a central composite design in order to study the interaction between the process variables and the responses, includingCO2permeance,CH4permeance andCO2/CH4separation factor. The optimum condition was then determined for maximumCO2permeance andCO2/CH4separation factor and minimumCH4permeance.RESULTS: Using this method,ZIF‐8 seeds of nano‐size were well distributed on the support due to high nucleation rate at the supersaturation condition. The presence of heavy hydrocarbons affectedCH4permeance, attributed to the molar mass and viscosity. An optimumCO2permeance of 2.76 × 10−8mol m−2s−1Pa−1andCO2/CH4separation factor of 3.72 was obtained at 312 K, 100kPaand 36%CO2feed composition. The experimental results were in agreement with the predicted values with an average error lower than ± 7%.CONCLUSION: SelectiveZIF‐8 membrane was successfully synthesized using a feasible and reproducible solvent evaporation seeding method. The experimental data for the optimum condition were in good agreement with the predicted data, showing the accuracy of the empirical models. © 2016 Society of Chemical Industry
- 25 January 2016
- Published by Taylor & Francis in Separation & Purification Reviews
- Vol. 45 (4) , 321-344
Current Development and Challenges of Mixed Matrix Membranes for CO2/CH4Separation
In the early stage of membrane technology development in gas separation, utilization of polymeric membranes has gained attention due to their robustness and ease of fabrication. However, the performance of polymeric membranes is limited by the trade-off between permeability and selectivity. Meanwhile, inorganic membrane is capable to exhibit great enhancement in separation performance but unfortunately its fabrication process is hard and costly. Thus, development of mixed matrix membranes (MMMs) by incorporating inorganic fillers into the polymer matrix has become a potential alternative to overcome the limitations of polymeric and inorganic membranes in gas separation. Nevertheless, fabrication of defect-free MMMs with improved separation performance and without compromising the mechanical and thermal stability is extremely difficult and challenging. In the current review paper, various types of inorganic fillers for MMMs fabrication and recent reported efforts to tailor the underlying problems on MMMs fabrication were discussed. The future outlook to advance the performance of MMMs in gas separation especially for CO2/CH4 separation was highlighted.
- 25 January 2016
- Published by Taylor & Francis in Separation & Purification Reviews
- Vol. 45 (4) , 321-344
Current Development and Challenges of Mixed Matrix Membranes for CO2/CH4Separation
In the early stage of membrane technology development in gas separation, utilization of polymeric membranes has gained attention due to their robustness and ease of fabrication. However, the performance of polymeric membranes is limited by the trade-off between permeability and selectivity. Meanwhile, inorganic membrane is capable to exhibit great enhancement in separation performance but unfortunately its fabrication process is hard and costly. Thus, development of mixed matrix membranes (MMMs) by incorporating inorganic fillers into the polymer matrix has become a potential alternative to overcome the limitations of polymeric and inorganic membranes in gas separation. Nevertheless, fabrication of defect-free MMMs with improved separation performance and without compromising the mechanical and thermal stability is extremely difficult and challenging. In the current review paper, various types of inorganic fillers for MMMs fabrication and recent reported efforts to tailor the underlying problems on MMMs fabrication were discussed. The future outlook to advance the performance of MMMs in gas separation especially for CO2/CH4 separation was highlighted.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1787 (1) , 040008
Spent coffee grounds-based activated carbon preparation for sequestering of malachite green
The key of reported work was to optimize the fabricating factors of spent coffee grounds-based activated carbon (SCG-bAC) used to sequester Malachite Green (MG) form aqueous solution via adsorption process. The fabricating factors of impregnation ratio with ortho-phosphoric acid, activation temperature and activation time were simultaneously optimized by central composite design (CCD) of response surface methodology (RSM) targeting on maximum removal of MG. At the optimum condition, 96.3% of MG was successfully removed by SCG-bAC at the impregnation ratio with ortho-phosphoric acid of 0.50, activation temperature of 554°C and activation time of 31.4 min. Statistical model that could predict the MG removal percentage was also derived and had been statistically confirmed to be significant. Subsequently, the MG adsorption equilibrium data was found well-fitted to Langmuir isotherm model, indicating the predominance of monolayer adsorption of MG on SCG-bAC surface. To conclude, the findings from the this study unveil the potential of spent coffee grounds as an alternative precursor in fabricating low-cost AC for the treatment of wastewater loaded with MG pollutant.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1787 (1) , 040008
Spent coffee grounds-based activated carbon preparation for sequestering of malachite green
The key of reported work was to optimize the fabricating factors of spent coffee grounds-based activated carbon (SCG-bAC) used to sequester Malachite Green (MG) form aqueous solution via adsorption process. The fabricating factors of impregnation ratio with ortho-phosphoric acid, activation temperature and activation time were simultaneously optimized by central composite design (CCD) of response surface methodology (RSM) targeting on maximum removal of MG. At the optimum condition, 96.3% of MG was successfully removed by SCG-bAC at the impregnation ratio with ortho-phosphoric acid of 0.50, activation temperature of 554°C and activation time of 31.4 min. Statistical model that could predict the MG removal percentage was also derived and had been statistically confirmed to be significant. Subsequently, the MG adsorption equilibrium data was found well-fitted to Langmuir isotherm model, indicating the predominance of monolayer adsorption of MG on SCG-bAC surface. To conclude, the findings from the this study unveil the potential of spent coffee grounds as an alternative precursor in fabricating low-cost AC for the treatment of wastewater loaded with MG pollutant.
- 18 September 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (96) , 79098-79106
CO 2 and CH 4 permeation through zeolitic imidazolate framework (ZIF)-8 membrane synthesized via in situ layer-by-layer growth: an experimental and modeling study
In this work, a general model representing the permeation of CO 2 and CH 4 through Zeolitic Imidazole Framework-8 (ZIF-8) membrane synthesized via in situ layer-by-layer growth under microwave irradiation is developed.
- 18 September 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (96) , 79098-79106
CO 2 and CH 4 permeation through zeolitic imidazolate framework (ZIF)-8 membrane synthesized via in situ layer-by-layer growth: an experimental and modeling study
In this work, a general model representing the permeation of CO 2 and CH 4 through Zeolitic Imidazole Framework-8 (ZIF-8) membrane synthesized via in situ layer-by-layer growth under microwave irradiation is developed.
- Open Access
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1133-1137
Fast Synthesis of Highly Crystalline ZIF-8 Using Microwave-Assisted Solvothermal Method
This paper presents the formation of highly crystalline ZIF-8 using microwave-assisted solvothermal method. The crystallinity of the ZIF-8 particles was characterized using X-ray diffraction. The lattice vibrations of the structure in the ZIF-8 framework were determined through Fourier transforms infrared spectroscopy. The morphology of the ZIF-8 particles was observed through scanning electron microscopy. The results showed that, 0.5 hour was sufficient for the formation of highly crystalline ZIF-8 particles using microwave-assisted solvothermal method under temperature 120 oC.
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1133-1137
Open AccessFast Synthesis of Highly Crystalline ZIF-8 Using Microwave-Assisted Solvothermal Method
This paper presents the formation of highly crystalline ZIF-8 using microwave-assisted solvothermal method. The crystallinity of the ZIF-8 particles was characterized using X-ray diffraction. The lattice vibrations of the structure in the ZIF-8 framework were determined through Fourier transforms infrared spectroscopy. The morphology of the ZIF-8 particles was observed through scanning electron microscopy. The results showed that, 0.5 hour was sufficient for the formation of highly crystalline ZIF-8 particles using microwave-assisted solvothermal method under temperature 120 oC.
- Open Access
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1096-1100
Methods Comparison for the Synthesis of Deca-Dodecasil 3 Rhombohedral (DDR3) Zeolite Crystals
In the present work, DDR3 zeolite crystals were synthesized using two different methods. The silica sources used to synthesize DDR3 crystals were tetramethoxysilane (TMOS) and Ludox-40. The resultant samples were characterized using X-ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM). The XRD results showed that the peaks representing DDR3 structure were not obtained for the sample synthesized in 5 days at room temperature with ultrasonic pre-treatment of 3h using Ludox-40 as silica source. On the other hand, the XRD pattern obtained for the sample synthesized in 25 days at 160 o C using TMOS as a silica source were similar with the XRD peaks reported in the literature. From these results, it can be concluded that the synthesis conditions of 25 days at 160 o C using TMOS as silica source were the favorable conditions in obtaining DDR3 crystal structure.
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1096-1100
Open AccessMethods Comparison for the Synthesis of Deca-Dodecasil 3 Rhombohedral (DDR3) Zeolite Crystals
In the present work, DDR3 zeolite crystals were synthesized using two different methods. The silica sources used to synthesize DDR3 crystals were tetramethoxysilane (TMOS) and Ludox-40. The resultant samples were characterized using X-ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM). The XRD results showed that the peaks representing DDR3 structure were not obtained for the sample synthesized in 5 days at room temperature with ultrasonic pre-treatment of 3h using Ludox-40 as silica source. On the other hand, the XRD pattern obtained for the sample synthesized in 25 days at 160 o C using TMOS as a silica source were similar with the XRD peaks reported in the literature. From these results, it can be concluded that the synthesis conditions of 25 days at 160 o C using TMOS as silica source were the favorable conditions in obtaining DDR3 crystal structure.
- Open Access
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1085-1090
Membranes for Gas Separation Current Development and Challenges
—A new bang of natural gas demand has opened up the opportunities towards the utilization of membrane technology for the purification process.The advantages in terms of smaller footprint, lower weight, minimum utility requirement and low labor intensity make them appropriate for wide scale applications. Polymeric membrane is one of the greatest emerging fields in membrane material development. Nevertheless, the separation performance of the existing polymeric materials were reached a limit in the trade-off between permeability and selectivity. The development of inorganic material gives a significance improvement in membrane performance but it outrageously expensive for many applications and having complicated procedure during fabrication process have limit the application of inorganic membrane in gas separation. Thus, a rapid demand in membrane technology for gas separation and the effort toward seeking the membranes with higher permeability and selectivity has motivated the development of mixed matrix membrane. Mixed matrix membrane (MMM) which incorporating inorganic fillers in a polymer matrix is expected to overcome the limitations of the polymeric and inorganic membranes. Apart from an overview of the different membrane materials for gas separation, this paper also highlights the development of mixed matrix membrane and challenges in fabrication of mixed matrix membranes.
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 773-774, 1085-1090
Open AccessMembranes for Gas Separation Current Development and Challenges
—A new bang of natural gas demand has opened up the opportunities towards the utilization of membrane technology for the purification process.The advantages in terms of smaller footprint, lower weight, minimum utility requirement and low labor intensity make them appropriate for wide scale applications. Polymeric membrane is one of the greatest emerging fields in membrane material development. Nevertheless, the separation performance of the existing polymeric materials were reached a limit in the trade-off between permeability and selectivity. The development of inorganic material gives a significance improvement in membrane performance but it outrageously expensive for many applications and having complicated procedure during fabrication process have limit the application of inorganic membrane in gas separation. Thus, a rapid demand in membrane technology for gas separation and the effort toward seeking the membranes with higher permeability and selectivity has motivated the development of mixed matrix membrane. Mixed matrix membrane (MMM) which incorporating inorganic fillers in a polymer matrix is expected to overcome the limitations of the polymeric and inorganic membranes. Apart from an overview of the different membrane materials for gas separation, this paper also highlights the development of mixed matrix membrane and challenges in fabrication of mixed matrix membranes.
- 23 February 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (29) , 22658-22664
Accelerated synthesis of deca-dodecasil 3 rhombohedral (DDR3) zeolite crystals via hydrothermal growth coupled with ultrasonic irradiation method
In the present work, DDR3 zeolite crystals were synthesized via hydrothermal heating coupled with ultrasonic irradiation method. The duration of hydrothermal heating was varied from 0.5–10 days and the temperature was maintained at 160 °C. Meanwhile, the duration of ultrasonic irradiation was varied from 1 h to 3 h. The crystallinity, surface morphology and bond vibration of the resultant samples were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR), respectively. The XRD results showed that the peaks representing DDR3 structure were obtained for the sample synthesized in 10 days with ultrasonic irradiation of 3 h. XRD peaks of the sample synthesized in 5 days with ultrasonic irradiation of 2 h also demonstrated the structure of DDR3 topology. Samples synthesized in 1, 2 and 5 days with ultrasonic irradiation of 1 h also demonstrated the structure of DDR3 topology. However, the sample synthesized in 0.5 day with 1 h of ultrasonic irradiation didn't showed DDR3 topology due to absence of major peaks in XRD pattern. For comparison purpose, reference DDR3 crystals were synthesized in 25 days without ultrasonic irradiation. From these results, it can be concluded that conventional hydrothermal heating coupled with ultrasonic irradiation has successfully reduced the synthesis duration of DDR3 zeolite from 25 days to 1 day.
- 23 February 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (29) , 22658-22664
Accelerated synthesis of deca-dodecasil 3 rhombohedral (DDR3) zeolite crystals via hydrothermal growth coupled with ultrasonic irradiation method
In the present work, DDR3 zeolite crystals were synthesized via hydrothermal heating coupled with ultrasonic irradiation method. The duration of hydrothermal heating was varied from 0.5–10 days and the temperature was maintained at 160 °C. Meanwhile, the duration of ultrasonic irradiation was varied from 1 h to 3 h. The crystallinity, surface morphology and bond vibration of the resultant samples were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR), respectively. The XRD results showed that the peaks representing DDR3 structure were obtained for the sample synthesized in 10 days with ultrasonic irradiation of 3 h. XRD peaks of the sample synthesized in 5 days with ultrasonic irradiation of 2 h also demonstrated the structure of DDR3 topology. Samples synthesized in 1, 2 and 5 days with ultrasonic irradiation of 1 h also demonstrated the structure of DDR3 topology. However, the sample synthesized in 0.5 day with 1 h of ultrasonic irradiation didn't showed DDR3 topology due to absence of major peaks in XRD pattern. For comparison purpose, reference DDR3 crystals were synthesized in 25 days without ultrasonic irradiation. From these results, it can be concluded that conventional hydrothermal heating coupled with ultrasonic irradiation has successfully reduced the synthesis duration of DDR3 zeolite from 25 days to 1 day.