Piyush Upadhyay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Piyush Upadhyay has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Hrishikesh Das
Pacific Northwest National Laboratory, Richland, USA
9 shared publications Hrishikesh Das
Pacific Northwest National Laboratory
5 shared publications- Ayoub Soulami
Pacific Northwest National Laboratory
3 shared publications - Adam Powell
Worcester Polytechnic Institute
2 shared publications - Avik Samanta
Department of Mechanical and Aerospace Engineering, University of South Florida, Tampa, USA
2 shared publications - Bharat Gwalani
Department of Materials Science and Engineering, North Carolina State University, Raleigh, USA
2 shared publications
Latest Publications
- 23 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (11-12) , 5455-5471
A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling
- 23 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (11-12) , 5455-5471
A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling
- Open Access
- 20 November 2023
- Published by Office of Scientific and Technical Information (OSTI)
Phase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints
In this study, WPI and its partners sought to understand galvanic corrosion in Mg-Al friction stir weld (FSW) joints. Unlike fusion welds, FSW is done in the solid state. This limits (but does not eliminate) the formation of brittle Al-Mg intermetallics, resulting in better joint strength and corrosion resistance. This study aimed to understand corrosion behavior of Mg-Al FSW joints by using a Cahn-Hilliard phase field electrochemistry model based on the work of Pongsaksawad et al. Its context challenge problem was an ultra-light door designed by Magna with 6061-Al sheet outer and ZEK100-Mg sheet inner panels, joined by an adhesive and FSW. Unlike most FSW joints, which weld through the softer material into the harder one, the Al sheet’s hem joint around Mg required the FSW tool to through the harder Al into the softer Mg, which was itself a challenge. Despite this challenge, PNNL succeeded in consistently making very strong FSW lap joints, by using a triflute tool and power control. Characterization showed mostly separate Al and Mg regions in the weld, usually with a hook protruding from Al into Mg, which likely contributed to high joint strength. Nanohardness mapping showed higher hardness in thin Mg swirls into the Al nugget, likely due to the intermetallics. The study used the industry standard SAE J2334 Cyclic Corrosion Test (CCT) to simulate corrosion conditions over the life of a vehicle, as well as linear polarization testing and ASTM G71 pitting corrosion testing. Corrosion reactions were: H₂O + ½O₂ + 2e⁻ → 2OH⁻ at the Al cathode, and either Mg → Mg²⁺ + 2e⁻ or Mg + 2OH⁻ → Mg(OH)₂ + 2e⁻ at the Mg anode, with electron transfer through the joint. Mass loss increased with Al section length, supporting the hypothesis that galvanic corrosion in Al-Mg joints is limited by the cathodic reaction. Both pitting corrosion (first anode reaction) and hydroxide film formation (second reaction) were observed. The J2334 CCT test method was slightly modified, adding a chromium solution cleaning step after each week of corrosion testing, in order to remove Mg oxides and hydroxides and accurately measure mass loss over time. That said, FSW joints treated in this way did not did not exhibit significant reduction in lap shear strength of the joints vs. newly welded samples which had not undergone corrosion. Corrosion appeared to consist mainly of pitting in Mg in a way which did not directly affect the bond between the materials where the joints failed. A Cahn-Hilliard phase field model coupled with electrical potential described the electronically mediated galvanic corrosion electrochemical reactions described above in the four-component Al-Mg-H₂O-(H₂O+½O₂) system. This 2-D model successfully predicted Mg(OH)₂ formation at the anode in some circumstances, and Mg pitting corrosion in others, and showed the correct electric field directions in both cases. The model predicted Mg pit corrosion depth within a factor of two of measured pits.
- 20 November 2023
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessPhase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints
In this study, WPI and its partners sought to understand galvanic corrosion in Mg-Al friction stir weld (FSW) joints. Unlike fusion welds, FSW is done in the solid state. This limits (but does not eliminate) the formation of brittle Al-Mg intermetallics, resulting in better joint strength and corrosion resistance. This study aimed to understand corrosion behavior of Mg-Al FSW joints by using a Cahn-Hilliard phase field electrochemistry model based on the work of Pongsaksawad et al. Its context challenge problem was an ultra-light door designed by Magna with 6061-Al sheet outer and ZEK100-Mg sheet inner panels, joined by an adhesive and FSW. Unlike most FSW joints, which weld through the softer material into the harder one, the Al sheet’s hem joint around Mg required the FSW tool to through the harder Al into the softer Mg, which was itself a challenge. Despite this challenge, PNNL succeeded in consistently making very strong FSW lap joints, by using a triflute tool and power control. Characterization showed mostly separate Al and Mg regions in the weld, usually with a hook protruding from Al into Mg, which likely contributed to high joint strength. Nanohardness mapping showed higher hardness in thin Mg swirls into the Al nugget, likely due to the intermetallics. The study used the industry standard SAE J2334 Cyclic Corrosion Test (CCT) to simulate corrosion conditions over the life of a vehicle, as well as linear polarization testing and ASTM G71 pitting corrosion testing. Corrosion reactions were: H₂O + ½O₂ + 2e⁻ → 2OH⁻ at the Al cathode, and either Mg → Mg²⁺ + 2e⁻ or Mg + 2OH⁻ → Mg(OH)₂ + 2e⁻ at the Mg anode, with electron transfer through the joint. Mass loss increased with Al section length, supporting the hypothesis that galvanic corrosion in Al-Mg joints is limited by the cathodic reaction. Both pitting corrosion (first anode reaction) and hydroxide film formation (second reaction) were observed. The J2334 CCT test method was slightly modified, adding a chromium solution cleaning step after each week of corrosion testing, in order to remove Mg oxides and hydroxides and accurately measure mass loss over time. That said, FSW joints treated in this way did not did not exhibit significant reduction in lap shear strength of the joints vs. newly welded samples which had not undergone corrosion. Corrosion appeared to consist mainly of pitting in Mg in a way which did not directly affect the bond between the materials where the joints failed. A Cahn-Hilliard phase field model coupled with electrical potential described the electronically mediated galvanic corrosion electrochemical reactions described above in the four-component Al-Mg-H₂O-(H₂O+½O₂) system. This 2-D model successfully predicted Mg(OH)₂ formation at the anode in some circumstances, and Mg pitting corrosion in others, and showed the correct electric field directions in both cases. The model predicted Mg pit corrosion depth within a factor of two of measured pits.
- 15 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1775-1788
On the Utility of the Thermal-Pseudo Mechanical Model’s Residual Stress Prediction Capability for the Development of Friction Stir Processing
- 15 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1775-1788
On the Utility of the Thermal-Pseudo Mechanical Model’s Residual Stress Prediction Capability for the Development of Friction Stir Processing
- Open Access
- 23 February 2023
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 4 (1) , 142-157
Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints
Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.
- 23 February 2023
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 4 (1) , 142-157
Open AccessMicrostructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints
Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.
- 20 December 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 124 (7-8) , 2957-2967
Improving local formability of 6xxx and 7xxx aluminum alloy sheets using friction stir processing
- 20 December 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 124 (7-8) , 2957-2967
Improving local formability of 6xxx and 7xxx aluminum alloy sheets using friction stir processing
- Open Access
- 25 October 2022
- Published by Springer Nature in Research Square
Improving Local Formability of Aluminum 6xxx and 7xxx Alloy Sheets using Friction Stir Processing for Automotive Applications
Friction stir processing (FSP) on a gantry setup was implemented on various high-strength commercial aluminum sheet metals, including 7085-T76, 7075-T6, 7055-T6, and 6111-T6, to improve the local formability of each alloy. Samples subjected to FSP were bend tested over a safe-to-fracture range by incrementally decreasing the radii of bending to find the radius to thickness ratio (r/t) at fracture. The locally processed region showed a formability improvement of 20% in 7075, 37% in 7055, 41% in 7085, and 71% in 6111 compared to the base alloys. A natural aging study on the FSP alloys showed only 12 hours of natural aging had lowered the elongation-to-fracture back to the base level for 7075 alloy, showing limited shelf life for forming applications for that alloy, whereas 6111 and 7055 alloys retained their elongationto-fracture improvements above the base alloy even after 2 weeks of natural aging. Effects of surface roughness on bending performance was tested on the 7085 alloy where a polished surface after FSP showed a slight improvement in r/t at fracture. Furthermore, the top and bottom surfaces of the processed sheet were bend tested at tension and compression, and the results showed that specimens processed at lower tool-head rotational speeds tended to fracture under tension but not under compression. Finally, FSP was incorporated into a robot tool head to evaluate the feasibility of local FSP for commercial applications at higher welding speeds of up to 5 m/min compared to the current gantry setup with its maximum welding speed of 2.9 m/min.
- 25 October 2022
- Published by Springer Nature in Research Square
Open AccessImproving Local Formability of Aluminum 6xxx and 7xxx Alloy Sheets using Friction Stir Processing for Automotive Applications
Friction stir processing (FSP) on a gantry setup was implemented on various high-strength commercial aluminum sheet metals, including 7085-T76, 7075-T6, 7055-T6, and 6111-T6, to improve the local formability of each alloy. Samples subjected to FSP were bend tested over a safe-to-fracture range by incrementally decreasing the radii of bending to find the radius to thickness ratio (r/t) at fracture. The locally processed region showed a formability improvement of 20% in 7075, 37% in 7055, 41% in 7085, and 71% in 6111 compared to the base alloys. A natural aging study on the FSP alloys showed only 12 hours of natural aging had lowered the elongation-to-fracture back to the base level for 7075 alloy, showing limited shelf life for forming applications for that alloy, whereas 6111 and 7055 alloys retained their elongationto-fracture improvements above the base alloy even after 2 weeks of natural aging. Effects of surface roughness on bending performance was tested on the 7085 alloy where a polished surface after FSP showed a slight improvement in r/t at fracture. Furthermore, the top and bottom surfaces of the processed sheet were bend tested at tension and compression, and the results showed that specimens processed at lower tool-head rotational speeds tended to fracture under tension but not under compression. Finally, FSP was incorporated into a robot tool head to evaluate the feasibility of local FSP for commercial applications at higher welding speeds of up to 5 m/min compared to the current gantry setup with its maximum welding speed of 2.9 m/min.
- Open Access
- 1 January 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (1) , 110-118
Friction-based riveting technique for AZ31 magnesium alloy
- 1 January 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (1) , 110-118
Open AccessFriction-based riveting technique for AZ31 magnesium alloy
- 1 July 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (12) , 1-29
Microstructure-Based Modeling of Friction Stir Welded Joint of Dissimilar Metals Using Crystal Plasticity
The friction stir welding (FSW) process shows promising results in joining dissimilar metals which are otherwise almost impossible to join using traditional welding techniques. Being a new technique, the deformation and the failure mechanism of the joints made by the FSW process needs to be investigated. In this work, a joint between AZ31 Mg alloy and DP590 steel is modeled using phenomenological crystal plasticity formulation on the mesoscale in the form of a representative volume element (RVE). The interface of the two materials is modeled using a cohesive zone model. A parametric study has been performed to understand the effect of grain size and interface fracture toughness as well as strength on the mechanical performance of the joint. It was found that the grain size of AZ31 Mg alloy, as well as DP590 steel, has little effect on the overall joint performance. On the other hand, interface fracture toughness and strength have a significant impact on the mechanical properties of the joint.
- 1 July 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (12) , 1-29
Microstructure-Based Modeling of Friction Stir Welded Joint of Dissimilar Metals Using Crystal Plasticity
The friction stir welding (FSW) process shows promising results in joining dissimilar metals which are otherwise almost impossible to join using traditional welding techniques. Being a new technique, the deformation and the failure mechanism of the joints made by the FSW process needs to be investigated. In this work, a joint between AZ31 Mg alloy and DP590 steel is modeled using phenomenological crystal plasticity formulation on the mesoscale in the form of a representative volume element (RVE). The interface of the two materials is modeled using a cohesive zone model. A parametric study has been performed to understand the effect of grain size and interface fracture toughness as well as strength on the mechanical performance of the joint. It was found that the grain size of AZ31 Mg alloy, as well as DP590 steel, has little effect on the overall joint performance. On the other hand, interface fracture toughness and strength have a significant impact on the mechanical properties of the joint.