Mariusz Twardawa
Research Subjects
Mariusz Twardawa has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Jerzy Okrajni
Faculty of Materials Engineering, Silesian University of Technology, 44-100 Gliwice, Poland
3 shared publications - Krzysztof Wacławiak
Faculty of Materials Engineering and Industrial Digitalization, Silesian University of Technology, Katowice, Poland
2 shared publications - Grzegorz Junak
Faculty of Materials Engineering, Silesian University of Technology, Krasińskiego 8, 40-019 Katowice, Poland
1 shared publication
Latest Publications
- Open Access
The Impact of Conventional Power Block Startup Procedures on the Fatigue Behavior of Drum Materials
Varying demands for electricity within the energy sector require the modification of operating modes to ensure both an uninterrupted electricity supply and the upholding of safety standards. This paper presents a method for the prediction of drum fatigue life, via the local analysis of stress–strain fields and low-cycle fatigue tests of the drum material. The analysis compares the fatigue properties of an unused material and a material that has undergone many years of operation. In addition, this paper suggests drum operating conditions based on the results of load testing under industrial conditions. The drum model was developed on the basis of technical documentation. The analysis includes the calculations of time-dependent temperature distributions, stresses, and strains for various drum startup modes. The drum material fatigue properties are determined under low-cycle conditions. Using the modeling results and fatigue properties, predictions of drum life for different startup modes are presented. The paper summarizes the impact of a range of startup procedures and the drum material fatigue properties on the fatigue life of a working drum, under various mechanical and thermal loads. In addition, this paper proposes a methodological approach to fatigue life assessment, as a combination of multiple research methods.
Open AccessThe Impact of Conventional Power Block Startup Procedures on the Fatigue Behavior of Drum Materials
Varying demands for electricity within the energy sector require the modification of operating modes to ensure both an uninterrupted electricity supply and the upholding of safety standards. This paper presents a method for the prediction of drum fatigue life, via the local analysis of stress–strain fields and low-cycle fatigue tests of the drum material. The analysis compares the fatigue properties of an unused material and a material that has undergone many years of operation. In addition, this paper suggests drum operating conditions based on the results of load testing under industrial conditions. The drum model was developed on the basis of technical documentation. The analysis includes the calculations of time-dependent temperature distributions, stresses, and strains for various drum startup modes. The drum material fatigue properties are determined under low-cycle conditions. Using the modeling results and fatigue properties, predictions of drum life for different startup modes are presented. The paper summarizes the impact of a range of startup procedures and the drum material fatigue properties on the fatigue life of a working drum, under various mechanical and thermal loads. In addition, this paper proposes a methodological approach to fatigue life assessment, as a combination of multiple research methods.
- Open Access
Impact of Heat Transfer on Transient Stress Fields in Power Plant Boiler Components
In boilers operating in modern power plants, thick-walled elements of complex shapes, such as valves, superheater headers, T-pipes, Y-pipes, four-way pipes, and elbows, are especially prone to fatigue processes. Higher operation parameters and more frequent startups may speed up fatigue damage in these elements. Such damage is a local phenomenon and is caused by thermomechanical fatigue (TMF). This paper presents a method designed for predicting the behavior of components subjected to variable temperature and mechanical loading conditions. This method combines the results of measurements of operating parameters of devices under industrial conditions with those obtained using finite element modeling (FEM). Particular attention was given to the influence of the time-dependent heat transfer coefficient on the local thermomechanical stress–strain behavior of the material. It was stated that heat transfer conditions have a significant impact on local transient stresses and depend on the operation parameters of boilers. Consistency of the temperature changes as a function of time, determined in industrial conditions and calculated on the basis of the model approach, was obtained. This developed and described in the work approach enables defining the conditions of heat transfer on the surface of models of considered components.
Open AccessImpact of Heat Transfer on Transient Stress Fields in Power Plant Boiler Components
In boilers operating in modern power plants, thick-walled elements of complex shapes, such as valves, superheater headers, T-pipes, Y-pipes, four-way pipes, and elbows, are especially prone to fatigue processes. Higher operation parameters and more frequent startups may speed up fatigue damage in these elements. Such damage is a local phenomenon and is caused by thermomechanical fatigue (TMF). This paper presents a method designed for predicting the behavior of components subjected to variable temperature and mechanical loading conditions. This method combines the results of measurements of operating parameters of devices under industrial conditions with those obtained using finite element modeling (FEM). Particular attention was given to the influence of the time-dependent heat transfer coefficient on the local thermomechanical stress–strain behavior of the material. It was stated that heat transfer conditions have a significant impact on local transient stresses and depend on the operation parameters of boilers. Consistency of the temperature changes as a function of time, determined in industrial conditions and calculated on the basis of the model approach, was obtained. This developed and described in the work approach enables defining the conditions of heat transfer on the surface of models of considered components.
- 15 April 2014
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 136 (4) , 041602
Influence of a Variable in Time Heat Transfer Coefficient on Stresses in Model of Power Plant Components
The paper discusses the issue of the modelling of strains and stresses resulting from heating and cooling processes of components in power plants. The main purpose of the work is to determine the mechanical behavior of power plant components operating under mechanical and thermal loading. The finite element method (FEM) has been used to evaluate the temperature and stresses changes in components as a function of time. Temperature fields in the components of power plants are dependent, among parameters, on variable heat-transfer conditions between components and the fluid medium, that may change its condition, flowing inside them. For this reason, an evaluation of the temperature field and the consequent stress fields requires the use of heat-transfer coefficients as time-dependent variables and techniques for determining appropriate values for these coefficients should be used. The methodology that combines computer modelling of the temperature fields with its measurements performed at selected points of the pipelines may be used in this case. The graphs of stress changes as a function of time have been determined for the chosen plant components. The influence of the heat transfer conditions on the temperature fields and mechanical behavior of components in question have been discussed.
- 15 April 2014
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 136 (4) , 041602
Influence of a Variable in Time Heat Transfer Coefficient on Stresses in Model of Power Plant Components
The paper discusses the issue of the modelling of strains and stresses resulting from heating and cooling processes of components in power plants. The main purpose of the work is to determine the mechanical behavior of power plant components operating under mechanical and thermal loading. The finite element method (FEM) has been used to evaluate the temperature and stresses changes in components as a function of time. Temperature fields in the components of power plants are dependent, among parameters, on variable heat-transfer conditions between components and the fluid medium, that may change its condition, flowing inside them. For this reason, an evaluation of the temperature field and the consequent stress fields requires the use of heat-transfer coefficients as time-dependent variables and techniques for determining appropriate values for these coefficients should be used. The methodology that combines computer modelling of the temperature fields with its measurements performed at selected points of the pipelines may be used in this case. The graphs of stress changes as a function of time have been determined for the chosen plant components. The influence of the heat transfer conditions on the temperature fields and mechanical behavior of components in question have been discussed.