Takashi Tachiki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Takashi Tachiki has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- H. B. Wang
Research Institute of Electrical Communication, Tohoku University, Sendai 980-8577, Japan
3 shared publications J. Chen
Research Institute of Electrical Communication, Tohoku University, Sendai 980-8577, Japan
3 shared publicationsK. Nakajima
Research Institute of Electrical Communication, Tohoku University, Sendai 980-8577, Japan
3 shared publicationsT. Uchida
National Defense Academy
3 shared publicationsT. Yamashita
New Industry Creation Hatchery Center, Tohoku University, Sendai, Japan
3 shared publications- Yasushi Ishiguro
Department of Electrical and Electronic Engineering, National Defense Academy, 1-10-20, Hashirimizu, Yokosuka, Kanagawa 239-8686, Japan
3 shared publications
Latest Publications
- 7 October 2025
- Published by IOP Publishing in Nanotechnology
- Vol. 36 (41) , 415502
Effect of nitrogen-vacancy defects in graphitic carbon nitride on hydrogen adsorption in quartz-crystal microbalance sensor for hydrogen gas
A graphitic carbon nitride (g-C3N4) with nitrogen-vacancy defects was synthesized by calcination of a mixture of melamine and potassium hydroxide (KOH). The nitrogen/carbon ratio (N/C) of the g-C3N4 film decreased with the addition of KOH, indicating that the KOH addition could control the nitrogen-vacancy defects in the g-C3N4. The g-C3N4 films with nitrogen-vacancy defects were formed on a quartz crystal substrate. The change in the resonant frequency of the crystal was measured before and after the introduction of hydrogen gas, utilizing the quartz crystal microbalance (QCM) method. This approach was employed to characterize the hydrogen sensor effectively. The QCM-type sensor with the defective g-C3N4 film had a different frequency response to the hydrogen than the sensor with pristine g-C3N4 film synthesized without KOH addition. That is, the resonant frequency of the defective g-C3N4 decreased with the introduction of hydrogen, while that of pristine g-C3N4 was observed to increase. The reduced frequency of the defective g-C3N4 is probably due to the formation of chemical bonds with hydrogen (C-H) as observed in the FT-IR measurements. Our findings show that the introduction of nitrogen-vacancy defects into the g-C3N4 significantly impacts the characteristics of QCM-type hydrogen sensors. Moreover, controlling the amount of nitrogen vacancies introduced has a significant effect on the frequency response to the hydrogen gas. The QCM-type sensor utilizing g-C3N4 is anticipated to find applications in a range of gas sensors in the future, contingent upon the progress of research focused on controlling the precise number of nitrogen-vacancy defects.
- 7 October 2025
- Published by IOP Publishing in Nanotechnology
- Vol. 36 (41) , 415502
Effect of nitrogen-vacancy defects in graphitic carbon nitride on hydrogen adsorption in quartz-crystal microbalance sensor for hydrogen gas
A graphitic carbon nitride (g-C3N4) with nitrogen-vacancy defects was synthesized by calcination of a mixture of melamine and potassium hydroxide (KOH). The nitrogen/carbon ratio (N/C) of the g-C3N4 film decreased with the addition of KOH, indicating that the KOH addition could control the nitrogen-vacancy defects in the g-C3N4. The g-C3N4 films with nitrogen-vacancy defects were formed on a quartz crystal substrate. The change in the resonant frequency of the crystal was measured before and after the introduction of hydrogen gas, utilizing the quartz crystal microbalance (QCM) method. This approach was employed to characterize the hydrogen sensor effectively. The QCM-type sensor with the defective g-C3N4 film had a different frequency response to the hydrogen than the sensor with pristine g-C3N4 film synthesized without KOH addition. That is, the resonant frequency of the defective g-C3N4 decreased with the introduction of hydrogen, while that of pristine g-C3N4 was observed to increase. The reduced frequency of the defective g-C3N4 is probably due to the formation of chemical bonds with hydrogen (C-H) as observed in the FT-IR measurements. Our findings show that the introduction of nitrogen-vacancy defects into the g-C3N4 significantly impacts the characteristics of QCM-type hydrogen sensors. Moreover, controlling the amount of nitrogen vacancies introduced has a significant effect on the frequency response to the hydrogen gas. The QCM-type sensor utilizing g-C3N4 is anticipated to find applications in a range of gas sensors in the future, contingent upon the progress of research focused on controlling the precise number of nitrogen-vacancy defects.
- 13 August 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (9)
Growth of niobium thin films on C-plane and R-plane sapphire substrates for superconducting devices
Nb thin films were sputtered by heating C-plane and R-plane sapphire substrates to 800°C with a SiC heater and depositing the films via DC magnetron sputtering. XRD measurements confirmed that the films exhibited epitaxial growth, reflecting the crystal growth directions of Nb and sapphire. AFM revealed that triangular-shaped grains were present on the Nb thin films on the C-plane sapphire substrates and rectangular-shaped grains were present on the Nb thin films on the R-plane sapphire substrates. Resistivity-temperature measurements revealed that the RRR of Nb thin films on C-plane and R-plane sapphire substrates were 25.6 and 53.36, respectively. The RRR of Nb thin films on R-plane sapphire substrates was approximately twice higher than that of Nb thin films on C-plane sapphire substrates. Nb thin films on R-plane sapphire substrates can be used as materials for superconducting devices because they can form thin films with good crystallinity.
- 13 August 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (9)
Growth of niobium thin films on C-plane and R-plane sapphire substrates for superconducting devices
Nb thin films were sputtered by heating C-plane and R-plane sapphire substrates to 800°C with a SiC heater and depositing the films via DC magnetron sputtering. XRD measurements confirmed that the films exhibited epitaxial growth, reflecting the crystal growth directions of Nb and sapphire. AFM revealed that triangular-shaped grains were present on the Nb thin films on the C-plane sapphire substrates and rectangular-shaped grains were present on the Nb thin films on the R-plane sapphire substrates. Resistivity-temperature measurements revealed that the RRR of Nb thin films on C-plane and R-plane sapphire substrates were 25.6 and 53.36, respectively. The RRR of Nb thin films on R-plane sapphire substrates was approximately twice higher than that of Nb thin films on C-plane sapphire substrates. Nb thin films on R-plane sapphire substrates can be used as materials for superconducting devices because they can form thin films with good crystallinity.
- 1 May 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (5) , 056502
Detection of carbon monoxide and carbon dioxide gases using quartz crystal microbalance coated with a graphitic carbon nitride film
Graphitic carbon nitride (g-C3N4), a semiconducting material with a layered structure, has recently attracted attention as a gas sensing material because of its ability to adsorb various gas molecules. In this study, a g-C3N4 film was applied to a quartz crystal microbalance (QCM) to detect carbon monoxide (CO) and carbon dioxide (CO2) gases. The resonant frequency of the g-C3N4 film-coated quartz crystal changed with CO and CO2 gas introduction, and the frequency change increased linearly with gas concentration, suggesting quantitative detection is possible. In addition, the different rate constants for CO and CO2 gas introduction and ejection processes suggest that the g-C3N4-coated QCM electrode can identify gas molecular species based on their response rates. These results are expected to be useful for developing CO and CO2 gas sensors.
- 1 May 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (5) , 056502
Detection of carbon monoxide and carbon dioxide gases using quartz crystal microbalance coated with a graphitic carbon nitride film
Graphitic carbon nitride (g-C3N4), a semiconducting material with a layered structure, has recently attracted attention as a gas sensing material because of its ability to adsorb various gas molecules. In this study, a g-C3N4 film was applied to a quartz crystal microbalance (QCM) to detect carbon monoxide (CO) and carbon dioxide (CO2) gases. The resonant frequency of the g-C3N4 film-coated quartz crystal changed with CO and CO2 gas introduction, and the frequency change increased linearly with gas concentration, suggesting quantitative detection is possible. In addition, the different rate constants for CO and CO2 gas introduction and ejection processes suggest that the g-C3N4-coated QCM electrode can identify gas molecular species based on their response rates. These results are expected to be useful for developing CO and CO2 gas sensors.
- 27 December 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (1) , 01SP33
Fabrication of V1−x Ti x O2 microbolometers on Si3N4/SiO2 membranes
V1−x Ti x O2 thin films have been prepared on Si3N4/SiO2/Si substrates by the two-step process of (1) growth of VO2/TiO2 thin films by metal-organic decomposition with carbothermal reduction, and (2) the interdiffusion between V and Ti atoms at the interface between the VO2 and TiO2 thin films during the growth of the VO2 thin film. The abrupt resistance change and the thermal hysteresis due to the metal-insulator transition were gradually suppressed with increasing the firing temperature, and they completely disappeared for the V0.65Ti0.35O2 thin film prepared at 650 °C. A relatively high TCR of −4.2%/K was obtained from the film over a wide temperature range of 20 °C–90 °C. V0.65Ti0.35O2 microbolometers with a size of 5 μm × 15 μm were fabricated by photolithography and Ar ion milling, and a Si3N4/SiO2 membrane under the microbolometer was formed with an aqueous KOH solution. The DC sensitivity of the fabricated microbolometer on the membrane was estimated to be 9876 W−1 and 20 times higher than that of the microbolometer on the Si3N4/SiO2/Si substrate. The V0.65Ti0.35O2 microbolometer on the membrane is available for a terahertz detector operating over the wide temperature range.
- 27 December 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (1) , 01SP33
Fabrication of V1−x Ti x O2 microbolometers on Si3N4/SiO2 membranes
V1−x Ti x O2 thin films have been prepared on Si3N4/SiO2/Si substrates by the two-step process of (1) growth of VO2/TiO2 thin films by metal-organic decomposition with carbothermal reduction, and (2) the interdiffusion between V and Ti atoms at the interface between the VO2 and TiO2 thin films during the growth of the VO2 thin film. The abrupt resistance change and the thermal hysteresis due to the metal-insulator transition were gradually suppressed with increasing the firing temperature, and they completely disappeared for the V0.65Ti0.35O2 thin film prepared at 650 °C. A relatively high TCR of −4.2%/K was obtained from the film over a wide temperature range of 20 °C–90 °C. V0.65Ti0.35O2 microbolometers with a size of 5 μm × 15 μm were fabricated by photolithography and Ar ion milling, and a Si3N4/SiO2 membrane under the microbolometer was formed with an aqueous KOH solution. The DC sensitivity of the fabricated microbolometer on the membrane was estimated to be 9876 W−1 and 20 times higher than that of the microbolometer on the Si3N4/SiO2/Si substrate. The V0.65Ti0.35O2 microbolometer on the membrane is available for a terahertz detector operating over the wide temperature range.
- 12 February 2018
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 13 (6) , 876-881
Characteristics of thin‐film spiral antenna‐coupled Bi microbolometer fabricated on Si3N4/SiO2 membrane
A thin‐film spiral antenna‐coupled Bi microbolometer was fabricated on a Si3N4/SiO2 membrane. The membrane was realized by wet etching from the back of an Si substrate using a 26 wt% KOH solution. The antenna was designed in accordance with the current band theory so that it covers the frequency range of 140–220 GHz. The experimental patterns for antennas located on the membrane and on the membrane backed by a copper plate reflector were in good agreement with theoretical patterns for the antenna located in air. Furthermore, a wide band characteristic of the antenna ranging from 140 to 220 GHz was obtained. The responsivity of the Bi microbolometer on the membrane estimated from the DC sensitivity under the irradiation of 220 GHz electromagnetic wave was 110 V/W. This value is about one order of magnitude higher than that of a Bi bolometer fabricated on a dielectric substrate. © 2018 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.
- 12 February 2018
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 13 (6) , 876-881
Characteristics of thin‐film spiral antenna‐coupled Bi microbolometer fabricated on Si3N4/SiO2 membrane
A thin‐film spiral antenna‐coupled Bi microbolometer was fabricated on a Si3N4/SiO2 membrane. The membrane was realized by wet etching from the back of an Si substrate using a 26 wt% KOH solution. The antenna was designed in accordance with the current band theory so that it covers the frequency range of 140–220 GHz. The experimental patterns for antennas located on the membrane and on the membrane backed by a copper plate reflector were in good agreement with theoretical patterns for the antenna located in air. Furthermore, a wide band characteristic of the antenna ranging from 140 to 220 GHz was obtained. The responsivity of the Bi microbolometer on the membrane estimated from the DC sensitivity under the irradiation of 220 GHz electromagnetic wave was 110 V/W. This value is about one order of magnitude higher than that of a Bi bolometer fabricated on a dielectric substrate. © 2018 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-4
Effect of RF Isolation of Intrinsic Josephson Junctions Made of Solid Bi-2212 Film for Terahertz Radiation
This is the first report of THz radiation from intrinsic Josephson junction devices made of solid Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+\delta}$thin films. It is shown that in-situ laser trimming of the current lead structure could activate initially THz inactive devices. The trimming increased inductive reactance and improved RF isolation of intrinsic Josephson junctions. It is considered that the RF isolation is a key component to maintain a cavity resonance within intrinsic Josephson junctions essential to create THz waves from solid Bi-2212 film IJJ devices.
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-4
Effect of RF Isolation of Intrinsic Josephson Junctions Made of Solid Bi-2212 Film for Terahertz Radiation
This is the first report of THz radiation from intrinsic Josephson junction devices made of solid Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+\delta}$thin films. It is shown that in-situ laser trimming of the current lead structure could activate initially THz inactive devices. The trimming increased inductive reactance and improved RF isolation of intrinsic Josephson junctions. It is considered that the RF isolation is a key component to maintain a cavity resonance within intrinsic Josephson junctions essential to create THz waves from solid Bi-2212 film IJJ devices.
- 18 April 2014
- Published by Springer Nature in Journal of Infrared, Millimeter, and Terahertz Waves
- Vol. 35 (6-7) , 509-516
Evaluation of Cavity Modes in Superconducting Intrinsic-Josephson-Junction Oscillators for Terahertz-wave Generation
- 18 April 2014
- Published by Springer Nature in Journal of Infrared, Millimeter, and Terahertz Waves
- Vol. 35 (6-7) , 509-516
Evaluation of Cavity Modes in Superconducting Intrinsic-Josephson-Junction Oscillators for Terahertz-wave Generation
- 30 November 2011
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 471 (21-22) , 1206-1209
Influence of thermal noise on terahertz-wave radiation from intrinsic Josephson junctions
- 30 November 2011
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 471 (21-22) , 1206-1209
Influence of thermal noise on terahertz-wave radiation from intrinsic Josephson junctions
- 18 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 21 (3) , 168-171
Intrinsic Josephson Junctions in Bi-2212 Thin Films Fabricated by Metal-Organic Decomposition
We fabricated a mesa 10 μm × 10 μm in area and ~ 150 nm in height on a single grain in a 240-nm Bi2Sr2CaCu2O8+δ/MgO thin-film grown by metal-organic decomposition (MOD) with face-to-face annealing. A multi-branch structure peculiar to intrinsic Josephson junctions (IJJs) was observed in the I-V characteristics of the fabricated mesa, and this structure was characterized by approximately 100 quasiparticle branches with critical current densities of 1 kA/cm2 and voltage-jump intervals of 20 mV. Moreover, the temperature dependence of the critical current was in good agreement with a theoretical result based on c-axis Josephson tunneling in d-wave superconductors. These results imply that the thin films grown by MOD have sufficient quality to fabricate IJJs for practical terahertz applications.
- 18 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 21 (3) , 168-171
Intrinsic Josephson Junctions in Bi-2212 Thin Films Fabricated by Metal-Organic Decomposition
We fabricated a mesa 10 μm × 10 μm in area and ~ 150 nm in height on a single grain in a 240-nm Bi2Sr2CaCu2O8+δ/MgO thin-film grown by metal-organic decomposition (MOD) with face-to-face annealing. A multi-branch structure peculiar to intrinsic Josephson junctions (IJJs) was observed in the I-V characteristics of the fabricated mesa, and this structure was characterized by approximately 100 quasiparticle branches with critical current densities of 1 kA/cm2 and voltage-jump intervals of 20 mV. Moreover, the temperature dependence of the critical current was in good agreement with a theoretical result based on c-axis Josephson tunneling in d-wave superconductors. These results imply that the thin films grown by MOD have sufficient quality to fabricate IJJs for practical terahertz applications.
- 31 May 2009
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 469 (15-20) , 1604-1607
Investigation of I–V characteristics of Bi-2212 intrinsic Josephson junctions for THz-wave generation
- 31 May 2009
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 469 (15-20) , 1604-1607
Investigation of I–V characteristics of Bi-2212 intrinsic Josephson junctions for THz-wave generation