WZWeizheng Zhang

Weizheng Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Weizheng Zhang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:

  • J. Yan

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, 100081, China

    3 shared publications
  • S. Jin

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, 100081, China

    3 shared publications
  • Y. Yuan

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, 100081, China

    3 shared publications
  • Yanpeng Yuan

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China

    3 shared publications
  • Z. Guo

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, 100081, China

    3 shared publications
  • Shuang Jin

    School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China

    2 shared publications

Latest Publications

  • Open Access

    Study on the Influence of Diesel Fuel Substitution Ratio on the Characteristics of Dual-Fuel Free-Piston Engines

    by Zhaoju Qin, Zhiao Zhang, Weihong Weng, Chenyang Yin, Zhen Han, Weizheng Zhang

    The diesel substitution ratio is a key parameter influencing the combustion characteristics and energy conversion efficiency of hydrogen diesel dual-fuel free-piston engines. This study develops a thermodynamic hydrodynamic coupled model for a dual-fuel free engine to investigate the effects of five substitution ratios (15%, 20%, 25%, 30%, and 35%) on in-cylinder mixture formation, combustion characteristics, and emission performance. The key novelty of this work lies in employing this fully coupled combustion-dynamics model to systematically optimize the hydrogen–diesel substitution ratio, which explicitly captures the critical feedback between combustion and the piston’s unique motion. The cumulative heat release served as the key quantitative metric. The analyzed parameters included the gas mixture fraction, turbulent kinetic energy, flow trajectories, in-cylinder pressure and temperature, combustion reaction rate, unburned equivalent ratio, cumulative heat release and its rate, heat release rate, and emission mass. The results demonstrate that the engine’s overall performance is optimal at a substitution ratio of 25%. At this ratio, a peak volumetric mixture fraction of 0.0088 was achieved with a broad distribution range, indicating significantly improved spatial fuel uniformity. The flow field exhibited organized swirl patterns that enhanced fuel dispersion. The peak in-cylinder pressure reached 7.2 MPa, which was 0.044 MPa higher than that of the 20% group. The combustion temperature remained stable, with a peak value of 1606 K, exceeding the 20% and 30% groups by 7 K and 16 K, respectively. The heat release phase was well-synchronized with the piston motion, ensuring a high proportion of premixed combustion for thorough fuel oxidation. Although nitrogen oxide (NOx) emissions were slightly higher, the reduction in soot was substantially greater than in the 20% group, leading to overall superior performance compared to the other substitution ratios. This study develops a thermodynamic hydrodynamic coupled model for a dual-fuel free-piston engine by leveraging the interaction between piston motion and combustion. This paper presents a novel strategy for optimizing the substitution ratio in a free piston engine via a fully coupled combustion-dynamics model.

  • Open Access

    Experimental Investigation of Fuel Film Characteristics after Spray Impacting on Ultra-cold Surface

    by S. Jin, W. Zhang, Z. Guo, Y. Yuan, J. Yan, Y. Liu

    In extremely cold environments, the phenomenon of spray impacting on surfaces is unavoidable and the fuel film attached to the surface is one of the crucial factors influencing emission, stability, and cold-start performance in internal combustion engines. However, there is currently a lack of research on the effects of spray impacting on ultra-cold surfaces. In this study, researchers investigated the effect of surface temperature on impinging spray and fuel film area with different values of injection pressure, injection duration, and surface roughness visually using backlight and scattering methods. The penetration and diameter of the impinging spray were not affected by the low surface temperature due to the ample momentum, whereas the height was slightly decreased at the ultra-cold surface. The fuel film area significantly decreased with the lower surface temperature and the shorter injection duration. An empirical correlation for the fuel film area was established for reflecting the relationship between the fuel film area and the low surface temperature or injection conditions. The decrease in fuel film area was more noticeable on the surface with lower temperature and higher surface roughness (Ra=17.69μm). Nevertheless, the longer injection duration weakened this decreasing trend. With the increasing number of injections, the fuel film area rose while the area on the ultra-cold surface, increased more slowly because of the higher viscosity and thickness of the previous residual film.

  • Dynamic Characteristics of the Droplet Impact on the Ultracold Surface under the Engine Cold Start Conditions

    by S. Jin, W. Zhang, Z. Guo, Y. Yuan, Z. Shi, Y. Liu, J. Yan

    The impact of liquid droplets on the ultracold surface affects significantly the cold start performance of internal combustion engines but the splash and spreading characteristics after impacting on the ultracold surface are not clearly understood. Therefore, droplets with various physical parameters impacting on the Al–Si alloy surface have been selected for the study under various surface temperatures (–40°C ≤ \(~{{T}_{s}}~\) ≤ 25°C) and droplet impact velocities (0.96 m/s ≤ \(~{{V}_{0}}~\) ≤ 3.52 m/s). The ultracold surface (\({{T}_{s}}\) = –40°C) is beneficial for corona splash, and droplets with the higher Oh number impacting on the ultracold surface easily produce corona splash as the main splash pattern. The ultracold surface assisted in enhancing the stability of the levitated lamella formation, and avoided the effects of rough surfaces, so the upper splash criterion is established to predict the transition from spreading to splash. The decreasing surface temperature reduces the maximum spreading diameter (\({{{{\beta }}}_{{{\text{max}},{\text{lt}}}}}\)) of low solidification point droplets (ethanol, n-propanol, and winter diesel). Based on the assumptions of qualitative temperature, the empirical correlation of the \({{{{\beta }}}_{{{\text{max}},{\text{lt}}}}}\) is created for the Ts from 25 to –40°C.


  • Experimental Study on a Water Droplet Impacting on the Heated Glycerol Surface

    by S. Jin, W. Zhang, Z. Guo, Y. Yuan, Z. Shi, J. Yan

    The phenomena of droplet impact on the heated liquid surface are difficult to unify due to complexity of the interaction, but this process has significance for the study such as direct fuel injection in internal-combustion engines or pool fire suppression. A series of experiments on a water droplet impacting on the heated glycerol surface are carried under various surface temperatures (111.4°C ≤ Tgly ≤ 270.6°C) and impact Weber number (50.5 ≤ We ≤ 297.9). Four regimes, including penetration, crater–jet, vapor explosion and crater–jet–vapor explosion, are discussed in detail. With increase in the Tgly and We, the phenomena transform easier from penetration to crater–jet. The jet formation is affected by the interaction of vapor explosion (Tgly ≥ 222.3°C) and this process is mainly caused by two factors: the vapor explosion appears at the liquid-liquid interface and the vapor explosion time is equal to 4.8–15.8 ms. Increase in Tgly and We prolongs the crater evolution process and leads to growth of the maximum dimensionless crater depth (hmax). The contribution index shows that hmax is significantly increased by the vapor explosion and continued to increase for the higher We. Furthermore, the secondary breakup of droplets is observed at Tgly ≥ 222.3°C and this phenomenon mainly includes the processes of puffing, sputtering, vaporization and deformation.

  • Open Access

    Experimental investigation of heat transfer for diesel spray impingement on a high temperature wall

    by Zhenyao Guo, Weizheng Zhang, Shuang Jin, Zhicheng Shi, Yanpeng Yuan

    In this paper, the heat transfer characteristics of spray-wall impingement on a high temperature wall were studied by using a transient thermocouple and a one-dimensional finite-difference conduction model to obtain variations of wall temperature and heat flux. Results showed that increasing the injection pressure and decreasing the ambient temperature both caused an increase in surface heat flux and heat transfer coefficient. However, with the increase of the initial surface temperature from 200 to 600 °C, the surface heat flux and heat transfer coefficient first increased and then decreased, and reached the maximum at about 520 °C and 390 °C respectively, which was due to the change of heat transfer regime on the wall. The contribution of experimental factors descended in the order of initial surface temperature, injection pressure and ambient temperature. The dimensionless surface heat fluxes in terms of Biot and Fourier numbers were highly similar and a dimensionless correlation was developed to quantify this heat transfer behavior, which showed that the ratio of the thermal resistance of the high temperature wall to the thermal resistance of convection heat transfer on the wall surface changed almost linearly during the process of spray-wall impingement.


  • EFFECTS OF WALL TEMPERATURE ON THERMOPHYSICAL CHARACTERISTICS OF SPRAY-WALL IMPINGEMENT

    by Zhenyao Guo, Weizheng Zhang, Shuang Jin, Yanpeng Yuan

    For small- and medium-bore diesel engines, the phenomenon of spray-wall impingement is unavoidable, which affects the evaporation of the fuel, thermal efficiency, and emissions. Wall temperature is an important parameter in this process because it has an important influence on fuel evaporation. In this paper, the thermophysical characteristics of spray-wall impingement at different wall temperatures were studied. The results showed that with increase of the initial wall temperature, the impingement spray radius increased, but its rate of increase decreased, while the impingement spray height first increased and then decreased. During this process, the surface heat flux first increased and then decreased with the increase of initial wall temperature, which was due to the change of heat transfer regime on the wall. The transient heat transfer process at different initial wall temperatures was characterized by the Biot and Fourier numbers and the dimensionless surface heat fluxes were highly similar. A dimensionless correlation was developed to quantify the transient heat transfer process, which showed that the ratio of the internal thermal resistance of heat conduction in the wall to the wall surface convective heat transfer resistance changes almost linearly during the process of spray-wall impingement.


  • Open Access

    Elevated Temperature Tensile Creep Behavior of Aluminum Borate Whisker-Reinforced Aluminum Alloy Composites (ABOw/Al–12Si)

    by Yameng Ji, Yanpeng Yuan, Weizheng Zhang, Yunqing Xu, Yuwei Liu

    In order to evaluate the elevated temperature creep performance of the ABOw/Al–12Si composite as a prospective piston crown material, the tensile creep behaviors and creep fracture mechanisms have been investigated in the temperatures range from 250 to 400 °C and the stress range from 50 to 230 MPa using a uniaxial tensile creep test. The creep experimental data can be explained by the creep constitutive equation with stress exponents of 4.03–6.02 and an apparent activation energy of 148.75 kJ/mol. The creep resistance of the ABOw/Al–12Si composite is immensely improved by three orders of magnitude, compared with the unreinforced alloy. The analysis of the ABOw/Al–12Si composite creep data revealed that dislocation climb is the main creep deformation mechanism. The values of the threshold stresses are 37.41, 25.85, and 17.36 at elevated temperatures of 300, 350 and 400 °C, respectively. A load transfer model was introduced to interpret the effect of whiskers on the creep rate of this composite. The creep test data are very close to the predicted values of the model. Finally, the fractographs of the specimens were analyzed by Scanning Electron Microscope (SEM), the fracture mechanisms of the composites at different temperatures were investigated. The results showed that the fracture characteristic of the ABOw/Al–12Si composite exhibited a macroscale brittle feature range from 300 to 400 °C, but a microscopically ductile fracture was observed at 400 °C. Additionally, at a low tensile creep temperature (300 °C), the plastic flow capacity of the matrix was poor, and the whisker was easy to crack and fracture. However, during tensile creep at a higher temperature (400 °C), the matrix was so softened that the whiskers were easily pulled out and interfacial debonding appeared.


  • Open Access

    Effects of contact pressure and interface temperature on thermal contact resistance between 2Cr12NiMoWV/BH137 and γ-TiAl/2Cr12NiMoWV interfaces

    by Yuwei Liu, Yameng Ji, Fuhao Ye, Weizheng Zhang, Shujun Zhou

    Thermal contact resistance between interfaces is an important parameter in the analysis of temperature distribution for structural components. Thermal contact resistance between heat resistant steel 2Cr12NiMoWV/aluminum alloy BH137 interfaces and 2Cr12NiMoWV/titanium alloy ?-TiAl interfaces were experimentally investigated in the present paper. The effects of contact pressure and interface tem-perature were detailed. The temperature of contacting surfaces was from 80- 250?, and the contact pressure ranged from 2-17 MPa. All experiments were conducted in ambient atmosphere. Results showed that thermal contact resistance decreases with an increment of interface temperature or contact pressure. Under the same conditions of contact pressure and interface temperature, thermal contact resistance between 2Cr12NiMoWV and BH137 interfaces is lower than that between 2Cr12NiMoWV and ?-TiAl interfaces. The temperature dependence of thermal conductivity and mechanical properties was analyzed to explain the results. Furthermore, with the piston and piston pin as the research object, steady state temperature fields were simulated in cases of considering thermal contact resistance and without considering thermal contact resistance, respectively. The results showed that the maximum temperature of the piston pin will be lower when thermal contact resistance is considered.