Mohammad Javad Azarhoosh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Javad Azarhoosh has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Habib Ale Ebrahim
Department of Chemical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
2 shared publications - Faezeh Farivar
Department of Computer and Mechatronics Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
1 shared publication S. H. Pourtarah
Chemical Engineering Department, Petrochemical Center of Excellence, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
1 shared publication
Latest Publications
- Open Access
- 21 March 2017
- Published by Juniper Publishers in Current Trends in Biomedical Engineering & Biosciences
- Vol. 2 (3)
Application of Biomaterials in Dentistry
- 21 March 2017
- Published by Juniper Publishers in Current Trends in Biomedical Engineering & Biosciences
- Vol. 2 (3)
Open AccessApplication of Biomaterials in Dentistry
- 28 July 2014
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 203 (1) , 53-63
Simulating and Optimizing Auto-Thermal Reforming of Methane to Synthesis Gas Using a Non-Dominated Sorting Genetic Algorithm II Method
Conventional synthesis gas production plants consist of a natural gas steam reforming to CO + 3H2 on Ni catalysts in a furnace. An alternative method for highly endothermic steam reforming is auto-thermal reforming. In this work, synthesis gas production by auto-thermal reforming was simulated based on a heterogeneous and one-dimensional model in two cases. The first case was the auto-thermal reformer of Dias and Assaf's study. The present work was validated by the reported experimental results. The second case was the fixed-bed catalytic auto-thermal reactor operated at high pressure, which was suitable for methanol production and Fischer–Tropsch reactions (baseline case). Then, the effect of operating variables on the system behavior was studied. Finally, Pareto-optimal solutions were determined by non-dominated sorting genetic algorithm II. The objectives included obtaining a H2/CO ratio of 2 in the produced synthesis gas and the maximum methane conversion. The adjustable parameters were the feed temperature, mass flux, and O2/CH4 and H2O/CH4 ratios in the feed.
- 28 July 2014
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 203 (1) , 53-63
Simulating and Optimizing Auto-Thermal Reforming of Methane to Synthesis Gas Using a Non-Dominated Sorting Genetic Algorithm II Method
Conventional synthesis gas production plants consist of a natural gas steam reforming to CO + 3H2 on Ni catalysts in a furnace. An alternative method for highly endothermic steam reforming is auto-thermal reforming. In this work, synthesis gas production by auto-thermal reforming was simulated based on a heterogeneous and one-dimensional model in two cases. The first case was the auto-thermal reformer of Dias and Assaf's study. The present work was validated by the reported experimental results. The second case was the fixed-bed catalytic auto-thermal reactor operated at high pressure, which was suitable for methanol production and Fischer–Tropsch reactions (baseline case). Then, the effect of operating variables on the system behavior was studied. Finally, Pareto-optimal solutions were determined by non-dominated sorting genetic algorithm II. The objectives included obtaining a H2/CO ratio of 2 in the produced synthesis gas and the maximum methane conversion. The adjustable parameters were the feed temperature, mass flux, and O2/CH4 and H2O/CH4 ratios in the feed.
- 23 January 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (26) , 13419-13429
Simulation and optimization of a horizontal ammonia synthesis reactor using genetic algorithm
The synthesis of ammonia from nitrogen and hydrogen is one of the most important processes in petrochemical industry. In this study simulation and optimization of a horizontal ammonia synthesis reactor is presented in two cases: first, an intercooled horizontal ammonia synthesis reactor of the Khorasan petrochemical plant, second, a horizontal ammonia synthesis reactor with two quench flows. The one-dimensional heterogeneous mathematical model consists of two point boundary value differential equations for the catalyst pellets which were used in the simulations. Also, the effectiveness factor was calculated by both an empirical relation and considering the diffusion-reaction equations. The differential equations of boundary and initial value problems are solved with a combination of the Runge–Kutta method and an improved shooting method. The simulation was done for two cases. The first case is an intercooled horizontal ammonia converter, and the second one is a horizontal ammonia converter with two quench flows. Good agreement is achieved between simulated results, i.e., the outlet component mole fraction and temperature, and industrial data (Khorasan plant data and SRI report). Then the effect of parameters like inlet temperature, total feed flow rate, and operating pressure on ammonia production is studied. Finally, optimum solutions for the maximum mass flow rate production of ammonia are determined using a genetic algorithm (GA). The adjustable parameters are inlet temperature, total feed flow rate and operating pressure. The results of optimization show that a maximum ammonia mass flux of 52 433 kg h−1 and 73 979 kg h−1 was produced in both cases, respectively, in which the inlet temperature, feed flow rate, and operating pressure were, respectively, 524 °C, 217 005 kg h−1 and 167 atm in the first case and 437 °C, 354 986 kg h−1 and 237 atm in the second one.
- 23 January 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (26) , 13419-13429
Simulation and optimization of a horizontal ammonia synthesis reactor using genetic algorithm
The synthesis of ammonia from nitrogen and hydrogen is one of the most important processes in petrochemical industry. In this study simulation and optimization of a horizontal ammonia synthesis reactor is presented in two cases: first, an intercooled horizontal ammonia synthesis reactor of the Khorasan petrochemical plant, second, a horizontal ammonia synthesis reactor with two quench flows. The one-dimensional heterogeneous mathematical model consists of two point boundary value differential equations for the catalyst pellets which were used in the simulations. Also, the effectiveness factor was calculated by both an empirical relation and considering the diffusion-reaction equations. The differential equations of boundary and initial value problems are solved with a combination of the Runge–Kutta method and an improved shooting method. The simulation was done for two cases. The first case is an intercooled horizontal ammonia converter, and the second one is a horizontal ammonia converter with two quench flows. Good agreement is achieved between simulated results, i.e., the outlet component mole fraction and temperature, and industrial data (Khorasan plant data and SRI report). Then the effect of parameters like inlet temperature, total feed flow rate, and operating pressure on ammonia production is studied. Finally, optimum solutions for the maximum mass flow rate production of ammonia are determined using a genetic algorithm (GA). The adjustable parameters are inlet temperature, total feed flow rate and operating pressure. The results of optimization show that a maximum ammonia mass flux of 52 433 kg h−1 and 73 979 kg h−1 was produced in both cases, respectively, in which the inlet temperature, feed flow rate, and operating pressure were, respectively, 524 °C, 217 005 kg h−1 and 167 atm in the first case and 437 °C, 354 986 kg h−1 and 237 atm in the second one.