Timothy G. Rials
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Timothy G. Rials has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Omid Hosseinaei
Center for Renewable Carbon, University of Tennessee, 2506 Jacob Drive, Knoxville, TN 37996, USA
2 shared publications - Stephen S. Kelley
Department of Forest Biomaterials, College of Natural Resources, North Carolina State University, Raleigh, USA
2 shared publications - Adam Taylor
University of Tennessee
1 shared publication - Allison E. Ray
Energy & Environment Science & Technology, Idaho National Laboratory, 1955 N. Fremont Avenue, Idaho Falls, Idaho 83415, United States
1 shared publication Bryce Stokes
CNJV, LLC
1 shared publication- Cheng Xing
Tennessee Forest Products Center, University of Tennessee, Knoxville, USA
1 shared publication
Latest Publications
- Open Access
- 3 December 2019
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 7
Editorial: Advancements in Biomass Feedstock Preprocessing: Conversion Ready Feedstocks
Editorial: Advancements in Biomass Feedstock Preprocessing: Conversion Ready Feedstocks
- 3 December 2019
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 7
Open AccessEditorial: Advancements in Biomass Feedstock Preprocessing: Conversion Ready Feedstocks
Editorial: Advancements in Biomass Feedstock Preprocessing: Conversion Ready Feedstocks
- Open Access
- 1 July 2017
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 18 (7) , 1410
Improving Processing and Performance of Pure Lignin Carbon Fibers through Hardwood and Herbaceous Lignin Blends
Lignin/lignin blends were used to improve fiber spinning, stabilization rates, and properties of lignin-based carbon fibers. Organosolv lignin from Alamo switchgrass (Panicum virgatum) and yellow poplar (Liriodendron tulipifera) were used as blends for making lignin-based carbon fibers. Different ratios of yellow poplar:switchgrass lignin blends were prepared (50:50, 75:25, and 85:15 w/w). Chemical composition and thermal properties of lignin samples were determined. Thermal properties of lignins were analyzed using thermogravimetric analysis and differential scanning calorimetry. Thermal analysis confirmed switchgrass and yellow poplar lignin form miscible blends, as a single glass transition was observed. Lignin fibers were produced via melt-spinning by twin-screw extrusion. Lignin fibers were thermostabilized at different rates and subsequently carbonized. Spinnability of switchgrass lignin markedly improved by blending with yellow poplar lignin. On the other hand, switchgrass lignin significantly improved thermostabilization performance of yellow poplar fibers, preventing fusion of fibers during fast stabilization and improving mechanical properties of fibers. These results suggest a route towards a 100% renewable carbon fiber with significant decrease in production time and improved mechanical performance.
- 1 July 2017
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 18 (7) , 1410
Open AccessImproving Processing and Performance of Pure Lignin Carbon Fibers through Hardwood and Herbaceous Lignin Blends
Lignin/lignin blends were used to improve fiber spinning, stabilization rates, and properties of lignin-based carbon fibers. Organosolv lignin from Alamo switchgrass (Panicum virgatum) and yellow poplar (Liriodendron tulipifera) were used as blends for making lignin-based carbon fibers. Different ratios of yellow poplar:switchgrass lignin blends were prepared (50:50, 75:25, and 85:15 w/w). Chemical composition and thermal properties of lignin samples were determined. Thermal properties of lignins were analyzed using thermogravimetric analysis and differential scanning calorimetry. Thermal analysis confirmed switchgrass and yellow poplar lignin form miscible blends, as a single glass transition was observed. Lignin fibers were produced via melt-spinning by twin-screw extrusion. Lignin fibers were thermostabilized at different rates and subsequently carbonized. Spinnability of switchgrass lignin markedly improved by blending with yellow poplar lignin. On the other hand, switchgrass lignin significantly improved thermostabilization performance of yellow poplar fibers, preventing fusion of fibers during fast stabilization and improving mechanical properties of fibers. These results suggest a route towards a 100% renewable carbon fiber with significant decrease in production time and improved mechanical performance.
- Open Access
- 30 July 2014
- Published by Springer Nature in BioEnergy Research
- Vol. 7 (3) , 765-768
Summary Report on the 2012 Sun Grant National Conference: Science for Biomass Feedstock Production and Utilization
The 2012 Sun Grant National Conference on Science for Biomass Feedstock Production and Utilization was held on 2–5 October 2012, in New Orleans, LA, USA. The Sun Grant Initiative set out to highlight recent advances in science and technology contributing to the deployment of conventional and advanced biofuels and bioproducts from agricultural and forest systems. The Initiative, with sponsorship from the Department of Energy’s Bioenergy Technologies Office (BETO), assembled an agenda focusing on promoting collaboration between academic, industry, non-profit, and government partners. This special issue is comprised of a small sample of conference presentations selected to reflect important research progress and to highlight the range of issues that must be considered as the transition to biomass energy takes hold.
- 30 July 2014
- Published by Springer Nature in BioEnergy Research
- Vol. 7 (3) , 765-768
Open AccessSummary Report on the 2012 Sun Grant National Conference: Science for Biomass Feedstock Production and Utilization
The 2012 Sun Grant National Conference on Science for Biomass Feedstock Production and Utilization was held on 2–5 October 2012, in New Orleans, LA, USA. The Sun Grant Initiative set out to highlight recent advances in science and technology contributing to the deployment of conventional and advanced biofuels and bioproducts from agricultural and forest systems. The Initiative, with sponsorship from the Department of Energy’s Bioenergy Technologies Office (BETO), assembled an agenda focusing on promoting collaboration between academic, industry, non-profit, and government partners. This special issue is comprised of a small sample of conference presentations selected to reflect important research progress and to highlight the range of issues that must be considered as the transition to biomass energy takes hold.
- 1 January 2011
- Published by Forest Products Society in Forest Products Journal
- Vol. 61 (1) , 31-37
Effect of Hemicellulose Extraction on Physical and Mechanical Properties and Mold Susceptibility of Flakeboard
Hemicellulose is the most hydrophilic polymer of wood, and as a polysaccharide, it has potential applications in conversion to biofuels. The objective of this study was to enhance properties of flakeboard by extracting hemicellulose. Hot-water pretreatment was performed to extract hemicellulose under different temperatures (140°C, 155°C, and 170°C) and times (30 and 60 min). The flakes were blended with 5 percent liquid phenol-formaldehyde resin and 1 percent wax emulsion. The mat was pressed at 200°C for 5 minutes. The physical and mechanical properties and the susceptibility of flakeboard to mold were studied. Panels made from the hemicellulose-extracted flakes showed remarkable decreases in water absorption and thickness swelling without a decrease in mechanical properties. Resistance of the panels to the mold growth also increased with increasing mass loss due to extraction. The most severe condition of extraction (170°C, 60 min), in addition to having the lowest water absorption and thickness swelling, showed the highest mold resistance.
- 1 January 2011
- Published by Forest Products Society in Forest Products Journal
- Vol. 61 (1) , 31-37
Effect of Hemicellulose Extraction on Physical and Mechanical Properties and Mold Susceptibility of Flakeboard
Hemicellulose is the most hydrophilic polymer of wood, and as a polysaccharide, it has potential applications in conversion to biofuels. The objective of this study was to enhance properties of flakeboard by extracting hemicellulose. Hot-water pretreatment was performed to extract hemicellulose under different temperatures (140°C, 155°C, and 170°C) and times (30 and 60 min). The flakes were blended with 5 percent liquid phenol-formaldehyde resin and 1 percent wax emulsion. The mat was pressed at 200°C for 5 minutes. The physical and mechanical properties and the susceptibility of flakeboard to mold were studied. Panels made from the hemicellulose-extracted flakes showed remarkable decreases in water absorption and thickness swelling without a decrease in mechanical properties. Resistance of the panels to the mold growth also increased with increasing mass loss due to extraction. The most severe condition of extraction (170°C, 60 min), in addition to having the lowest water absorption and thickness swelling, showed the highest mold resistance.
- 1 April 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (4) , 279-285
Correlation of Near-Infrared Spectroscopy Measurements with the Properties of Treated Wood
Near-infrared (NIR) spectroscopy was used to predict the longitudinal tensile modulus, the longitudinal tensile strength, and the creosote content of wood from an out-of-service southern pine utility pole. Tensile samples were cut from the pole in the radial direction and near-infrared spectra were obtained before testing. Coefficients of determination , of 0.80–0.86 were obtained between the NIR spectra predicted modulus and measured modulus. Coefficients of determination for strength were lower, 0.58–0.63. After tensile testing, the specimens were ground in a mill and spectra were obtained from the homogeneous ground samples. There was a slight decrease in the coefficients of determination using the ground samples, 0.76–0.82 for the modulus and 0.46–0.57 for the strength. Creosote content was difficult to predict with the NIR spectra of the whole sample, but coefficients of determination were obtained with the ground samples. There was little difference in the results for spectra collected over the range and those obtained with just looking at the range. This suggests that it will be feasible to predict the mechanical properties of treated timber using lightweight, relatively inexpensive, portable instruments rather than larger, more expensive systems that cover the entire NIR range.- 1 April 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (4) , 279-285
Correlation of Near-Infrared Spectroscopy Measurements with the Properties of Treated Wood
Near-infrared (NIR) spectroscopy was used to predict the longitudinal tensile modulus, the longitudinal tensile strength, and the creosote content of wood from an out-of-service southern pine utility pole. Tensile samples were cut from the pole in the radial direction and near-infrared spectra were obtained before testing. Coefficients of determination , of 0.80–0.86 were obtained between the NIR spectra predicted modulus and measured modulus. Coefficients of determination for strength were lower, 0.58–0.63. After tensile testing, the specimens were ground in a mill and spectra were obtained from the homogeneous ground samples. There was a slight decrease in the coefficients of determination using the ground samples, 0.76–0.82 for the modulus and 0.46–0.57 for the strength. Creosote content was difficult to predict with the NIR spectra of the whole sample, but coefficients of determination were obtained with the ground samples. There was little difference in the results for spectra collected over the range and those obtained with just looking at the range. This suggests that it will be feasible to predict the mechanical properties of treated timber using lightweight, relatively inexpensive, portable instruments rather than larger, more expensive systems that cover the entire NIR range.