Tiago Ramos Ribeiro
Research Subjects
Tiago Ramos Ribeiro has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- André Luiz Nunis da Silva
Laboratory of Metallurgical Processes, IPT—Institute for Technological Research of Sao Paulo State, Av. Prof. Almeida Prado, Sao Paulo 05508-901, SP, Brazil
2 shared publications - Antônio Malynowskyj
Laboratory of Metallurgical Processes, Institute for Technological Research (IPT), São Paulo, Brazil
2 shared publications - Catia Fredericci
Institute for Technological Research (IPT)
2 shared publications - Fabiano Ferreira Chotoli
Institute for Technological Research (IPT)
2 shared publications - João Batista Ferreira Neto
Laboratory of Metallurgical Processes, Institute for Technological Research (IPT), São Paulo, Brazil
2 shared publications - João O. G. Faria
Laboratory of Metallurgical Processes, Institute for Technological Research (IPT), São Paulo, Brazil
2 shared publications
Latest Publications
- Open Access
- 15 January 2021
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 61 (1) , 182-189
Steam Reforming of Methane on Sponge Iron: Influence of Gas Composition on Reaction Rate
Direct Reduction processes use gases (CO and H2) for iron reduction and production of sponge iron or direct reduced iron (DRI). The generation of this gas occurs through methane reforming, which can be done in a reformer or inside the reduction shaft with the sponge iron as a catalyst. The latter occurs in the auto-reforming processes. The kinetics of steam reforming of methane catalyzed by sponge iron was studied at temperatures between 875°C and 1050°C. Results showed that sponge iron acts as a catalyst and methane conversion is increased in higher temperatures and with higher H2/H2O ratio in the inlet gas. The inlet gas composition like one of the industrial auto-reforming processes led to intense carburization and hindered the catalytic reforming reaction.
- 15 January 2021
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 61 (1) , 182-189
Open AccessSteam Reforming of Methane on Sponge Iron: Influence of Gas Composition on Reaction Rate
Direct Reduction processes use gases (CO and H2) for iron reduction and production of sponge iron or direct reduced iron (DRI). The generation of this gas occurs through methane reforming, which can be done in a reformer or inside the reduction shaft with the sponge iron as a catalyst. The latter occurs in the auto-reforming processes. The kinetics of steam reforming of methane catalyzed by sponge iron was studied at temperatures between 875°C and 1050°C. Results showed that sponge iron acts as a catalyst and methane conversion is increased in higher temperatures and with higher H2/H2O ratio in the inlet gas. The inlet gas composition like one of the industrial auto-reforming processes led to intense carburization and hindered the catalytic reforming reaction.
- Open Access
- 11 July 2018
- Published by IntechOpen
Iron Ore Pelletizing Process: An Overview
The iron ore production has significantly expanded in recent years, owing to increasing steel demands in developing countries. However, the content of iron in ore deposits has deteriorated and low-grade iron ore has been processed. The fines resulting from the concentration process must be agglomerated for use in iron and steelmaking. This chapter shows the status of the pelletizing process with a special focus on binders. Bentonite is the most used binder due to favorable mechanical and metallurgical pellet properties, but it contains impurities especially silica and alumina. The importance of many researches concerning alternative binders is also discussed in this chapter. Better quality wet, dry, preheated, and fired pellets can be produced with combined binders, such as organic and inorganic salts, when compared with bentonite-bonded pellets. While organic binders provide sufficient wet and dry pellet strengths, inorganic salts provide the required preheated and fired pellet strengths.
- 11 July 2018
- Published by IntechOpen
Open AccessIron Ore Pelletizing Process: An Overview
The iron ore production has significantly expanded in recent years, owing to increasing steel demands in developing countries. However, the content of iron in ore deposits has deteriorated and low-grade iron ore has been processed. The fines resulting from the concentration process must be agglomerated for use in iron and steelmaking. This chapter shows the status of the pelletizing process with a special focus on binders. Bentonite is the most used binder due to favorable mechanical and metallurgical pellet properties, but it contains impurities especially silica and alumina. The importance of many researches concerning alternative binders is also discussed in this chapter. Better quality wet, dry, preheated, and fired pellets can be produced with combined binders, such as organic and inorganic salts, when compared with bentonite-bonded pellets. While organic binders provide sufficient wet and dry pellet strengths, inorganic salts provide the required preheated and fired pellet strengths.
- 19 June 2017
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 3 (4) , 720-728
Modification of Basic Oxygen Furnace Slag for Cement Manufacturing
- 19 June 2017
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 3 (4) , 720-728
Modification of Basic Oxygen Furnace Slag for Cement Manufacturing
- Open Access
- 13 October 2015
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 2 (1) , 13-27
Modification of Molten Steelmaking Slag for Cement Application
- 13 October 2015
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 2 (1) , 13-27
Open AccessModification of Molten Steelmaking Slag for Cement Application
- 9 September 2014
- Published by Springer Nature in Metallurgical and Materials Transactions E
- Vol. 1 (4) , 286-291
Effects of Solidification Rate and Settling Time of SiC Particles on the Macrosegregation of Carbon in Silicon Ingots
- 9 September 2014
- Published by Springer Nature in Metallurgical and Materials Transactions E
- Vol. 1 (4) , 286-291
Effects of Solidification Rate and Settling Time of SiC Particles on the Macrosegregation of Carbon in Silicon Ingots
- Open Access
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 66 (4) , 479-484
Silicon refining by a metallurgical processing route
Directional solidification experiments were carried out in a Bridgman furnace to remove carbon and metallic impurities from silicon. For carbon removal, solidification was achieved by extracting the mold from the hot into the cold zone of the furnace, while for the removal of metallic impurities, solidification occurred by cooling the furnace with a motionless mold. In the experiments of carbon removal, a mold extraction rate of 5 µm/s results in an ingot with columnar grain structure aligned in the ingot axial direction and a macrosegregation of carbon and SiC particles to the ingot top regions. However, at a mold extraction rate of 80 µm/s, the grain structure consisted of columnar grains aligned in the radial direction and SiC particles were observed throughout the ingot, showing lower macrosegregation with a carbon concentration still larger at the ingot top. In the metallic impurities removal experiment, an ingot with a columnar grain structure aligned in the ingot axial direction was obtained and the concentration profiles showed significant metallic impurities macrosegregation to the ingot top.
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 66 (4) , 479-484
Open AccessSilicon refining by a metallurgical processing route
Directional solidification experiments were carried out in a Bridgman furnace to remove carbon and metallic impurities from silicon. For carbon removal, solidification was achieved by extracting the mold from the hot into the cold zone of the furnace, while for the removal of metallic impurities, solidification occurred by cooling the furnace with a motionless mold. In the experiments of carbon removal, a mold extraction rate of 5 µm/s results in an ingot with columnar grain structure aligned in the ingot axial direction and a macrosegregation of carbon and SiC particles to the ingot top regions. However, at a mold extraction rate of 80 µm/s, the grain structure consisted of columnar grains aligned in the radial direction and SiC particles were observed throughout the ingot, showing lower macrosegregation with a carbon concentration still larger at the ingot top. In the metallic impurities removal experiment, an ingot with a columnar grain structure aligned in the ingot axial direction was obtained and the concentration profiles showed significant metallic impurities macrosegregation to the ingot top.