MKMarkus Kaspar

Markus Kaspar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Markus Kaspar has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Climate‐resilient asset management: New perspectives for structural inspection

    by Volker Reinprecht, Markus Kaspar, D. Scott Kieffer, Franz Tschuchnigg, Matthias J. Rebhan

    Climate change, structural ageing and natural hazards are placing increasing pressure on alpine transport infrastructure. Current visual and largely reactive inspection practices lack the proactive integration of environmental data and, consequently, the incorporation of climate change into maintenance strategies. The MORICE research project closes this gap by combining remote sensing and hydrochemical diagnostics with the integration of expert knowledge on climate‐change‐related effects and structural ageing into inspection practice. The approach operates at two interconnected scales: at network level, GIS‐based screening identifies route sections with adverse climatic exposure, while at asset level hydrochemical parameters, remote‐sensing data and automated measurement systems complement visual inspection. Case studies and sensitivity analyses were used to investigate the influence of the groundwater regime and water chemistry on the reliability of drainage facilities and retaining structures, and to develop a systematic approach for integrating hydrochemical investigations. On this basis, the paper derives adjustments to structural inspection that enable early damage detection and identifies implications for upgrading existing assets and designing future assets.

  • Slaking sensitivity of rocks – insights from a multi laboratory parameter study

    by Markus Kaspar, Christine Latal, Gerhard Pittino

    The slaking behaviour of rocks is of geotechnical importance, affecting the stability of slopes and excavation pits, for example, as well as influencing the performance of underground excavation works, such as clogging of TBMs. Traditionally, wetting-drying and slake durability tests are performed to assess the degradation behaviour of weak rocks. Depending on their genetic origin, the slaking and disintegration behaviour of these rocks may exhibit different patterns. This study uses the results of widely used slaking tests, combined with the characterisation of disintegrated materials/decay products, to propose a tool for evaluating slaking sensitivity. Combining and extending the evaluation of these tests with mineral composition data and mechanical parameters enables a more detailed evaluation of the slaking behaviour of weak and soft rocks. Sedimentary rocks exhibit strong static slaking, whereas weak rocks derived from crystalline rocks slake under dynamic conditions. These findings have wider implications for estimating rock degradation in different geological settings and offer a quick laboratory method of estimating slaking rates and the potential liberation of fines, for example in the event of extreme precipitation.

  • Open Access

    Degradation and Decay of Rocks: Linking Wetting–Drying and Slake Durability Tests for Climate-Sensitive Maintenance

    by Markus Kaspar, Christine Latal, Gerhard Pittino, Volker Reinprecht

    Soft and weak rocks present challenges for construction activities in various environments. Their genetic origin, geological and tectonic evolution, and exposure to atmospheric conditions control their weathering and degradation over time. Therefore, a sound characterization of the associated rock parameters is essential. Numerous tests have been developed and standardized or defined in recommendations to assess various geomechanical, petrological, and mineralogical parameters. However, these tests are still subject to modification or extension to address project-specific issues. Additionally, standardized tests do not consider regional climatic conditions that may affect weathering, meaning they do not reflect the degradation behavior that is observed in the field. The present study investigates the slaking resistance and degradability of a range of soft rocks. The workflow of widely used tests is employed to evaluate their representativeness for different rock types in practical applications. Depending on their genetic origin and mineral composition, fabric alterations affect the rate and style of rock disintegration differently. Soft sedimentary rocks react already to static slaking, i.e., water immersion, whereas crystalline and grain-bound rocks slake under dynamic action while undergoing attrition in a rotating slake durability drum. Zones of structural weakness, such as foliation planes, are responsible for material removal in the latter; sedimentary rocks, on the other hand, are subject to surface particle separation (suspension) and suction due to the presence of clay minerals. This study presents an approach that combines the results of several routine tests to help identify and refine the slaking susceptibility of different rock types. A routine for inspecting and documenting the evaluated slaking characteristics for infrastructure maintenance is proposed, and the wider implications in light of climate change are discussed. Some limitations of the transferability of laboratory values to field sites still have to be evaluated and validated in the future.


  • Advances in remote sensing techniques in engineering geology for infrastructure inspection and site characterization

    by Volker Reinprecht, Markus Kaspar

    Remote sensing technologies have significantly transformed engineering geology over the past two decades, enabling efficient data collection for infrastructure inspection and site characterization. Advances in sensor platforms, including unmanned aerial vehicle (UAV)‐based photogrammetry, light detection and ranging (LiDAR), and interferometric synthetic aperture radar (InSAR), have led to significant advances in terrain monitoring, rock mass characterization, and geohazard assessment. While these technologies improve data accuracy and accessibility, they also introduce challenges related to data processing and integration. This study discusses the advantages and limitations of active and passive remote sensing methods and emphasizes their role in engineering geological investigations. Based on short case studies, the study emphasizes the need for multidisciplinary approaches to fully exploit remote sensing data in engineering geology, ensuring more reliable and cost‐effective infrastructure monitoring and hazard mitigation strategies.


  • Open Access

    An Extended Evaluation of the CERCHAR Abrasivity Test for a Practical Excavatability Assessment

    by Markus Kaspar, Christine Latal

    The CERCHAR abrasivity test is a widely used index test in earth and subsurface works, delivering numerical values for abrasion that are critical to the selection of excavation tools, TBM performance or cost and project schedule estimates. The test evaluates the wear of the tip of a standardized metal pin after a scratch test on a rock surface. However, excavatability is not considered in this test. The present study presents an approach to assessing the material removal of a rock specimen due to the scratching action of a steel pin. The concept is tested for a broad range of sedimentary, metamorphic and igneous rocks. The volume of removed rock material is determined by measuring the width of the scratch groove and assuming an idealized trapezoid geometry. The CAI and volumetric removal are used to calculate the CERCHAR abrasivity ratio (CAR), and the results are in good agreement with those from the literature where specialized equipment was used. A classification scheme to estimate the excavatability of rock based on the CAI in combination with the material removal of a rock specimen is introduced. Based on the amount of material removed and the wear on the pin, an estimate can be made as to whether the excavation is likely to be economical in terms of time and material costs. The approach does not require additional testing, but rather makes use of the inherent geometry of the steel pin and the scratch groove on the rock specimen. The approach can be implemented as a complementary analysis to the existing CERCHAR test with little additional effort.


  • Open Access

    The Geomechanics of the Dangkhar Landslide, Himachal Pradesh, India

    by Markus Kaspar, D. Scott Kieffer

    The Dangkhar Landslide is an extremely large landslide located in the Spiti Valley of Himachal Pradesh, India. The landslide is situated in a remote high mountain desert within the Tethys Himalaya at elevations between 3400 m and 5600 m. It is amongst the five largest continental landslides on earth, covering an area of approximately 54 km2 and having an estimated volume of 15–20 km3. Geomechanical evaluations based on the block theory indicate that the Dangkhar Landslide formed as a result of unfavorable combinations of structural geological features and complex surface morphology. A massive kinematically removable block is created by a regional synclinal flexure that is crosscut and kinematically liberated by bounding side valleys. Three-dimensional block kinematics are necessary to permit the release of the giant block and its sliding along the synclinal flexure. Pseudostatic slope stability sensitivity analyses incorporating estimates of site seismicity and shear strength parameters suggest that earthquake shaking could have triggered instability if the static factor of safety was less than or in the range of about 1.5–1.9. Considering the glacial history of the region, ice debuttressing represents an additional potential triggering mechanism.


  • Mixed-Reality in der Ingenieurgeologie – von der Datenaufnahme bis zum immersiven 3D-Hologramm/Mixed-Reality in engineering geology – from data acquisition to immersive 3D holograms

    by Markus Kaspar, D. Scott Kieffer

    Die rasch voranschreitende Digitalisierung und wachsenden Mengen an (Geo)-daten stellen die Bauindustrie vor neue Herausforderungen. Moderne Geräte wie Drohnen und Laserscanner produzieren in kurzer Zeit enorme Datenmengen. Diese aufzubereiten und Auftraggebern, Planern oder Interessenvertretern verständlich zu präsentieren sind Teil von ingenieurgeologischen Aufgaben. Anstelle der üblicherweise verwendeten Pläne, Profilschnitte und statischen 3D-Modelle können diese Daten auf anschaulichere Weise in einer interaktiven, digitalen Umgebung präsentiert werden. Mixed-Reality Anwendungen bieten hierbei neue Möglichkeiten, den digitalen Zwilling eines Projektes in Form eines Hologramms virtuell und immersiv zu besuchen. Ortsunabhängige Besprechungen in Echtzeit an holografischen 3D-Modellen, ohne physisch den Ort zu wechseln, bringen Zeitersparnis und raschen Informationsaustausch mit sich. Dieser Aufsatz liefert einen Überblick über den Workflow zum Generieren von holografischen Daten bestehender Projekte und legt dar, was bei der Aufnahme und Verarbeitung von Daten für neue Projekte zu beachten ist. Der Schwerpunkt liegt auf ingenieurgeologischen Anwendungen, wobei die Möglichkeiten und Grenzen dieser Technologie erörtert werden.

  • Open Access

    Is soft rock also non-abrasive rock? An evaluation from lab testing campaigns

    by M Kaspar, C Latal, M Blümel, G Pittino

    Soft rocks are traditionally regarded in terms of low uniaxial compressive strength (UCS EQu) with emphasis on soft rocks. It is shown, that in order to assess the properties of soft rocks more accurately, the classification scheme can be expanded beyond the simple UCS approach by including mineralogical information and abrasivity values. This holistic approach more adequately captures the breadth of soft rock properties and allows a differentiated distinction of soft rocks in terms of strength and hardness.


  • Geologic, Geomorphologic, and Climatic Preparatory Conditions for the Evolution of the Dangkhar Landslide, Himachal Pradesh, India

    by Markus Kaspar, D. Scott Kieffer

    With an estimated volume of approximately 15 to 20 km3, the Dangkhar landslide located in the Spiti valley, Himachal Pradesh, India, is one of the largest landslides on earth. Its initiation is geochronologically constrained to have occurred during the late Pleistocene and may be related to glacial retreat following local last glacial maximum, which, depending on the source, occurred around 80 to 30 ka years ago. There is significant value in understanding the causative factors contributing to such an enormous and rare event. On the basis of comprehensive field studies and laboratory investigations, it is concluded that erosional, structural, and depositional features within and surroundings of the Dangkhar landslide are critical for understanding landslide initiation and its long-term behavior. The landslide developed as a block slide along a synformal flexure, and through-cutting lateral valleys fulfill the kinematic conditions for creating a massive removable block of earth. Deposits of weakly cemented and crudely bedded carbonate breccias in the landslide’s toe region represent depositional activity during recession of the main valley glacier, and cross-cutting structural relationships involving ground ruptures (lineaments) and rock glaciers in the head region record long-term, ongoing landslide deformations subsequent to its initiation. Stable isotope signatures of samples indicate presence of freshwater associated with the formation of breccia deposits. While many details concerning the timing and development of the Dangkhar landslide remain unknown, recent studies illuminate some very important aspects. The glacial history of the Spiti valley combined with structural kinematics are clearly important factors concerning landslide development. Also important are constraints concerning the minimum age of landslide initiation after recession of a valley glacier, and structural evidence documenting long-term ongoing slope deformations.