Rossella Bovolenta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rossella Bovolenta has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Bianca Federici
University of Genoa
8 shared publications - Roberto Passalacqua
University of Genoa
6 shared publications - Diana Bianchi
Department of Civil, Environmental and Mechanical Engineering, University of Trento, Trento, Italy
4 shared publications Dario Balestrero
Department of Civil, Chemical and Environmental Engineering, University of Genoa, Genoa, Italy
3 shared publications- Domenico Gallipoli
University of Genoa
3 shared publications - Martino Leoni
WeSi Geotecnica Srl, Italy & Adjunct Professor, Dipartimento di Ingegneria Civile, Chimica e Ambientale Università di Genova Genova Italy
3 shared publications
Latest Publications
- Open Access
- 3 August 2026
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 50 (16) , 5663-5679
Influence of Relative Permeability Formulations on Hysteretic Seepage in Infinite Slopes
The paper investigates the impact of two classical relative permeability formulations, one expressed in terms of pore water pressure and the other in terms of degree of saturation, on the predicted seepage in an infinite slope subjected to surface pore pressure variations. A hysteretic retention law is employed, inducing irreversible changes in hydraulic conductivity during wetting–drying cycles. Two soils with different gradings are analysed and, for each of them, the two relative permeability formulations are matched at a reference point so as to represent the same material. Despite this calibration, the corresponding permeability fields differ significantly over the hysteretic domain, by as much as five orders of magnitude. These discrepancies are mostly the consequence of retention hysteresis and are substantially reduced if a unique, non‐hysteretic retention curve is selected. For reference, a slope model with constant permeability, equal to the maximum saturated value, is also evaluated. The magnitude and rate of the slope response to surface perturbations, the number of cycles to restore equilibrium and the characteristics of the steady state regime all depend on the chosen permeability formulation. Slopes with a constant permeability react rapidly and uniformly, whereas slopes with permeability depending on pore water pressure or degree of saturation display slower, more complex and depth‐attenuated responses, particularly for the finer soil. Overall, the results highlight the need for consistent calibration of both relative permeability and retention hysteresis, while underscoring the limitations of constant permeability models in capturing unsaturated seepage, even when appropriate hysteretic retention laws are adopted.
- 3 August 2026
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 50 (16) , 5663-5679
Open AccessInfluence of Relative Permeability Formulations on Hysteretic Seepage in Infinite Slopes
The paper investigates the impact of two classical relative permeability formulations, one expressed in terms of pore water pressure and the other in terms of degree of saturation, on the predicted seepage in an infinite slope subjected to surface pore pressure variations. A hysteretic retention law is employed, inducing irreversible changes in hydraulic conductivity during wetting–drying cycles. Two soils with different gradings are analysed and, for each of them, the two relative permeability formulations are matched at a reference point so as to represent the same material. Despite this calibration, the corresponding permeability fields differ significantly over the hysteretic domain, by as much as five orders of magnitude. These discrepancies are mostly the consequence of retention hysteresis and are substantially reduced if a unique, non‐hysteretic retention curve is selected. For reference, a slope model with constant permeability, equal to the maximum saturated value, is also evaluated. The magnitude and rate of the slope response to surface perturbations, the number of cycles to restore equilibrium and the characteristics of the steady state regime all depend on the chosen permeability formulation. Slopes with a constant permeability react rapidly and uniformly, whereas slopes with permeability depending on pore water pressure or degree of saturation display slower, more complex and depth‐attenuated responses, particularly for the finer soil. Overall, the results highlight the need for consistent calibration of both relative permeability and retention hysteresis, while underscoring the limitations of constant permeability models in capturing unsaturated seepage, even when appropriate hysteretic retention laws are adopted.
- 1 October 2025
- Published by Springer Nature
- p. 102-117
Influence of Data Preprocessing and Optimization in Multivariate Statistical Analysis of Landslide Susceptibility
- 1 October 2025
- Published by Springer Nature
- p. 102-117
Influence of Data Preprocessing and Optimization in Multivariate Statistical Analysis of Landslide Susceptibility
- Open Access
- 1 October 2025
- Published by Springer Nature
- p. 3-19
Surface Soil Moisture Estimate by Integration of Optical Remote Sensing and Low-Cost Field Sensor Network: The Case Study of Ceriana-Mainardo (Liguria, Italy)
Surface Soil Moisture (SSM) is a fundamental information in various research contexts. The monitoring of soil moisture variations can be performed through an accurate use of sensors calibrated and distributed over the study areas. Also, remote sensing techniques can be used to estimate SSM, analyzing wide areas automatically. Starting from previous studies about the response of capacitive soil moisture sensors (WaterScout SM100) installed in the study area of Ceriana-Mainardo (Liguria, Italy), the present work aims to investigate the correlation between ground-based soil moisture data and reflectance extracted from Sentinel-2 images in a study area characterized by sparsely vegetated surfaces. Despite S-2 limitations due to sensitivity to atmospheric obstacles, they provide very effective monitoring of vegetation conditions, thanks to the Red Edge bands. In fact, Reflectance – Soil Moisture correlation analysis highlighted a better response for Red Edge 2, Red Edge 3, Broad Near Infrared and Near Infrared bands, being the vegetation cover spectral response an indirect indicator of soil moisture in the investigated depths. The best correlation is found referring to soil moisture at 10 cm depth and considering the mean reflectance of the four mentioned bands. This kind of dependency allows to have a quite good correlation (R 2 = 0.56, RES STD = 3.3% θ (m 3 /m 3 ), MAE = 2.1% θ (m 3 /m 3 )), comparable with the accuracy of the ground soil moisture sensors (3% θ), hence useful to extract spatially distributed information of Volumetric Water Content (θ [m 3 /m 3 %]) from S-2 images. The results of the analysis appear encouraging. The workflow, implemented on an area mostly characterized by complex cultivations, could be replicated on other vegetated land uses in presence of field soil moisture data in the study area.
- 1 October 2025
- Published by Springer Nature
- p. 3-19
Open AccessSurface Soil Moisture Estimate by Integration of Optical Remote Sensing and Low-Cost Field Sensor Network: The Case Study of Ceriana-Mainardo (Liguria, Italy)
Surface Soil Moisture (SSM) is a fundamental information in various research contexts. The monitoring of soil moisture variations can be performed through an accurate use of sensors calibrated and distributed over the study areas. Also, remote sensing techniques can be used to estimate SSM, analyzing wide areas automatically. Starting from previous studies about the response of capacitive soil moisture sensors (WaterScout SM100) installed in the study area of Ceriana-Mainardo (Liguria, Italy), the present work aims to investigate the correlation between ground-based soil moisture data and reflectance extracted from Sentinel-2 images in a study area characterized by sparsely vegetated surfaces. Despite S-2 limitations due to sensitivity to atmospheric obstacles, they provide very effective monitoring of vegetation conditions, thanks to the Red Edge bands. In fact, Reflectance – Soil Moisture correlation analysis highlighted a better response for Red Edge 2, Red Edge 3, Broad Near Infrared and Near Infrared bands, being the vegetation cover spectral response an indirect indicator of soil moisture in the investigated depths. The best correlation is found referring to soil moisture at 10 cm depth and considering the mean reflectance of the four mentioned bands. This kind of dependency allows to have a quite good correlation (R 2 = 0.56, RES STD = 3.3% θ (m 3 /m 3 ), MAE = 2.1% θ (m 3 /m 3 )), comparable with the accuracy of the ground soil moisture sensors (3% θ), hence useful to extract spatially distributed information of Volumetric Water Content (θ [m 3 /m 3 %]) from S-2 images. The results of the analysis appear encouraging. The workflow, implemented on an area mostly characterized by complex cultivations, could be replicated on other vegetated land uses in presence of field soil moisture data in the study area.
- Open Access
- 11 July 2025
- Published by Copernicus GmbH in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
- Vol. XLVIII-4/W, 209-216
Python plugin for statistical analysis of landslide susceptibility over wide areas
As part of the RETURN project, a model for assessing landslide susceptibility through logistic regression within a GIS environment has been developed, aimed at supporting public authorities and professionals in managing ground instability risks. The model utilizes freely accessible national-scale datasets to ensure high transferability and transparency of results. The analysis is implemented in Python and integrated into GRASS GIS, with the objective of automating the workflow and making the procedure accessible even to non-expert users. The methodology was tested in the Province of Savona (Liguria, Italy), using eight predisposing factors and landslide data from the IFFI inventory. The results demonstrated reliability exceeding 75% in most cases. The resulting susceptibility maps are reclassified into three qualitative categories—low, medium, and high susceptibility—to improve interpretability. The case study highlighted both the strengths and limitations of the approach, notably the need to standardize data and procedures to ensure applicability at broader scales. Ongoing development efforts are focused on enhancing the identification of relevant factors and minimizing subjectivity in data preparation. The automation of the model paves the way for extensive testing across different areas and geomorphological settings, contributing to the development of a robust tool for landslide risk management.
- 11 July 2025
- Published by Copernicus GmbH in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
- Vol. XLVIII-4/W, 209-216
Open AccessPython plugin for statistical analysis of landslide susceptibility over wide areas
As part of the RETURN project, a model for assessing landslide susceptibility through logistic regression within a GIS environment has been developed, aimed at supporting public authorities and professionals in managing ground instability risks. The model utilizes freely accessible national-scale datasets to ensure high transferability and transparency of results. The analysis is implemented in Python and integrated into GRASS GIS, with the objective of automating the workflow and making the procedure accessible even to non-expert users. The methodology was tested in the Province of Savona (Liguria, Italy), using eight predisposing factors and landslide data from the IFFI inventory. The results demonstrated reliability exceeding 75% in most cases. The resulting susceptibility maps are reclassified into three qualitative categories—low, medium, and high susceptibility—to improve interpretability. The case study highlighted both the strengths and limitations of the approach, notably the need to standardize data and procedures to ensure applicability at broader scales. Ongoing development efforts are focused on enhancing the identification of relevant factors and minimizing subjectivity in data preparation. The automation of the model paves the way for extensive testing across different areas and geomorphological settings, contributing to the development of a robust tool for landslide risk management.
- 1 July 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (8) , 820-828
Analysis of unsaturated seepage in infinite slopes by means of horizontal ground infiltration models
This paper describes a simple methodology to calculate the two-dimensional seepage across an infinite unsaturated slope using models of one-dimensional infiltration through horizontal ground. The methodology decomposes the seepage across the infinite slope into antisymmetric and symmetric parts, whose respective solutions are combined to calculate the actual flow regime. The antisymmetric solution is trivial and does not even require integration of the governing continuity equation, while the symmetric solution, albeit non-trivial, reduces to the case of one-dimensional flow through horizontal ground, for which solutions already exist. The methodology is generally applicable to the calculation of distinct seepage regimes across unsaturated slopes with different hydraulic properties under both stationary and transient conditions. The paper also defines the gradient of the piezometric head parallel to the slope, which is the Neumann boundary condition to be imposed on slope sections perpendicular to the ground surface. The rigorous definition of this gradient overcomes the need of imposing arbitrary boundary conditions in finite-element models. Finally, the paper demonstrates that all infiltrated water crosses the slope along the shortest path – namely, the path normal to the surface – while the flow parallel to the slope is entirely fed by an upstream source at infinite distance.
- 1 July 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (8) , 820-828
Analysis of unsaturated seepage in infinite slopes by means of horizontal ground infiltration models
This paper describes a simple methodology to calculate the two-dimensional seepage across an infinite unsaturated slope using models of one-dimensional infiltration through horizontal ground. The methodology decomposes the seepage across the infinite slope into antisymmetric and symmetric parts, whose respective solutions are combined to calculate the actual flow regime. The antisymmetric solution is trivial and does not even require integration of the governing continuity equation, while the symmetric solution, albeit non-trivial, reduces to the case of one-dimensional flow through horizontal ground, for which solutions already exist. The methodology is generally applicable to the calculation of distinct seepage regimes across unsaturated slopes with different hydraulic properties under both stationary and transient conditions. The paper also defines the gradient of the piezometric head parallel to the slope, which is the Neumann boundary condition to be imposed on slope sections perpendicular to the ground surface. The rigorous definition of this gradient overcomes the need of imposing arbitrary boundary conditions in finite-element models. Finally, the paper demonstrates that all infiltrated water crosses the slope along the shortest path – namely, the path normal to the surface – while the flow parallel to the slope is entirely fed by an upstream source at infinite distance.
- Open Access
- 25 April 2024
- Published by Springer Nature in Acta Geotechnica
- Vol. 19 (11) , 7207-7227
Long-term “memory” of extraordinary climatic seasons in the hysteretic seepage of an unsaturated infinite slope
This paper presents a study of the hydraulic response of an infinite unsaturated slope exposed to a perturbation of the ordinary seasonal climatic cycle. The ground flow is modelled via a simplified one-dimensional finite difference scheme by decomposing the two-dimensional slope seepage into antisymmetric and symmetric parts. The numerical scheme incorporates two distinct hysteretic and non-hysteretic soil water retention laws, whose parameters have been selected after a preliminary sensitivity analysis. Results indicate that, in the hysteretic case, the “memory” of the perturbation takes a long time to fade, and the ordinary soil saturation cycle is only restored after several years of normal weather. Instead, in the non-hysteretic case, the recovery of the ordinary saturation regime is almost immediate after the perturbation. In contrast with the markedly different predictions of degree of saturation, both hysteretic and non-hysteretic slope models predict virtually identical evolutions of negative pore water pressures, with an almost immediate restoration of the ordinary cycle after the perturbation.
- 25 April 2024
- Published by Springer Nature in Acta Geotechnica
- Vol. 19 (11) , 7207-7227
Open AccessLong-term “memory” of extraordinary climatic seasons in the hysteretic seepage of an unsaturated infinite slope
This paper presents a study of the hydraulic response of an infinite unsaturated slope exposed to a perturbation of the ordinary seasonal climatic cycle. The ground flow is modelled via a simplified one-dimensional finite difference scheme by decomposing the two-dimensional slope seepage into antisymmetric and symmetric parts. The numerical scheme incorporates two distinct hysteretic and non-hysteretic soil water retention laws, whose parameters have been selected after a preliminary sensitivity analysis. Results indicate that, in the hysteretic case, the “memory” of the perturbation takes a long time to fade, and the ordinary soil saturation cycle is only restored after several years of normal weather. Instead, in the non-hysteretic case, the recovery of the ordinary saturation regime is almost immediate after the perturbation. In contrast with the markedly different predictions of degree of saturation, both hysteretic and non-hysteretic slope models predict virtually identical evolutions of negative pore water pressures, with an almost immediate restoration of the ordinary cycle after the perturbation.
- 1 April 2021
- Published by Elsevier in Engineering Failure Analysis
- Vol. 122
Effect of deep excavations and deformable retaining structures on neighboring buildings: A case study
- 1 April 2021
- Published by Elsevier in Engineering Failure Analysis
- Vol. 122
Effect of deep excavations and deformable retaining structures on neighboring buildings: A case study
- Open Access
- 22 November 2020
- Published by MDPI AG in Geosciences
- Vol. 10 (11) , 473
Geotechnical Analysis and 3D Fem Modeling of Ville San Pietro (Italy)
The paper describes the three-dimensional numerical model of Ville San Pietro, an Italian village subject to slope movements causing damage. The church (dating back to 1776), which is the most significant building of the area, is modelled too. The information from geotechnical and geophysical surveys on field are used to define the model geometry and the soil properties. A finite element code is adopted to simulate the slope behavior in occurrence of water table fluctuations, detected by piezometers, and to evaluate the slope displacements and stability. The validation of the model is carried out using the inclinometer and interferometry measures and by on-site inspections. The model demonstrated a good ability to simulate the slope behavior during the raising and lowering of the water table. The critical areas computed by the numerical code are in good accordance to the actual portions affected by soil displacements and damages. The modelling presented in this paper is crucial for future analyses that will take advantage of an innovative monitoring system, which will be installed on site.
- 22 November 2020
- Published by MDPI AG in Geosciences
- Vol. 10 (11) , 473
Open AccessGeotechnical Analysis and 3D Fem Modeling of Ville San Pietro (Italy)
The paper describes the three-dimensional numerical model of Ville San Pietro, an Italian village subject to slope movements causing damage. The church (dating back to 1776), which is the most significant building of the area, is modelled too. The information from geotechnical and geophysical surveys on field are used to define the model geometry and the soil properties. A finite element code is adopted to simulate the slope behavior in occurrence of water table fluctuations, detected by piezometers, and to evaluate the slope displacements and stability. The validation of the model is carried out using the inclinometer and interferometry measures and by on-site inspections. The model demonstrated a good ability to simulate the slope behavior during the raising and lowering of the water table. The critical areas computed by the numerical code are in good accordance to the actual portions affected by soil displacements and damages. The modelling presented in this paper is crucial for future analyses that will take advantage of an innovative monitoring system, which will be installed on site.
- Open Access
- 13 October 2020
- Published by MDPI AG in Geosciences
- Vol. 10 (10) , 409
Field Measurements of Soil Water Content at Shallow Depths for Landslide Monitoring
Monitoring changes in soil saturation is important for slope stability analyses. Soil moisture capacitive sensors have recently been developed; their response time is extremely fast, they require little maintenance, and they are relatively inexpensive. The use of low-cost sensors in landslide areas can allow the monitoring of large territories, but appropriate calibration is required. Installation in the field and the setting up of the monitoring network also require attention. In the ALCOTRA AD-VITAM project, the University of Genoa is involved in the development of a system, called LAMP, for the monitoring, analysis and forecasting of slides triggered by rainfalls. Multiple installations (along vertical alignments) of WaterScout sensors are placed in the nodes of the monitoring network. They provide real-time water content profiles in the shallow layers (typically in the upper meter) of a slope. With particular reference to these measurements, the present paper describes the reliability analysis of the instruments, the operations related to the sensor calibration and the installation phases for the monitoring networks. Finally, some of the data coming from a node, belonging to one of the five monitoring networks, are reported.
- 13 October 2020
- Published by MDPI AG in Geosciences
- Vol. 10 (10) , 409
Open AccessField Measurements of Soil Water Content at Shallow Depths for Landslide Monitoring
Monitoring changes in soil saturation is important for slope stability analyses. Soil moisture capacitive sensors have recently been developed; their response time is extremely fast, they require little maintenance, and they are relatively inexpensive. The use of low-cost sensors in landslide areas can allow the monitoring of large territories, but appropriate calibration is required. Installation in the field and the setting up of the monitoring network also require attention. In the ALCOTRA AD-VITAM project, the University of Genoa is involved in the development of a system, called LAMP, for the monitoring, analysis and forecasting of slides triggered by rainfalls. Multiple installations (along vertical alignments) of WaterScout sensors are placed in the nodes of the monitoring network. They provide real-time water content profiles in the shallow layers (typically in the upper meter) of a slope. With particular reference to these measurements, the present paper describes the reliability analysis of the instruments, the operations related to the sensor calibration and the installation phases for the monitoring networks. Finally, some of the data coming from a node, belonging to one of the five monitoring networks, are reported.
- Open Access
- 30 June 2020
- Published by Czech Academy of Agricultural Sciences in Soil and Water Research
- Vol. 15 (2) , 75-84
The laboratory calibration of a soil moisture capacitance probe in sandy soils
The laboratory calibration of a soil moisture capacitance probe in sandy soils | Marina Campora, Anna Palla, Ilaria Gnecco, Rossella Bovolenta, Roberto Passalacqua | Agricultural Journals
- 30 June 2020
- Published by Czech Academy of Agricultural Sciences in Soil and Water Research
- Vol. 15 (2) , 75-84
Open AccessThe laboratory calibration of a soil moisture capacitance probe in sandy soils
The laboratory calibration of a soil moisture capacitance probe in sandy soils | Marina Campora, Anna Palla, Ilaria Gnecco, Rossella Bovolenta, Roberto Passalacqua | Agricultural Journals