Gerardo Larramona
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Gerardo Larramona has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Alain Jacob
IMRA Europe S.A.S 220 rue Albert CaquotBP 213 06904 Sophia Antipolis France
3 shared publicationsBruno Delatouche
IMRA Europe S.A.S 220 rue Albert CaquotBP 213 06904 Sophia Antipolis France
3 shared publicationsCamille Moisan
IMRA Europe S.A.S 220 rue Albert CaquotBP 213 06904 Sophia Antipolis France
3 shared publicationsChristophe Choné
IMRA Europe S.A.S 220 rue Albert CaquotBP 213 06904 Sophia Antipolis France
3 shared publications- Stéphane Bourdais
JIPELEC, Meylan, France
3 shared publications Daniel Péré
IMRA Europe S.A.S., 220 rue Albert Caquot, BP 213, 06904 Sophia Antipolis Cedex, France
2 shared publications
Latest Publications
- 15 October 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (24) , 1501404
Fine‐Tuning the Sn Content in CZTSSe Thin Films to Achieve 10.8% Solar Cell Efficiency from Spray‐Deposited Water–Ethanol‐Based Colloidal Inks
Thin film solar cells with Al/ITO/ZnO/CdS/CZTSSe/Mo‐glass structure are fabricated employing a fast and low‐cost preparation procedure using an aqueous ink deposited by nonpyrolytic spray, followed by high temperature crystallization and selenization steps. Capacitance–voltage measurements on previously reported devices with >8% efficiency under 1 sun irradiation show a charge carrier density of the order of 1017 cm−3. Moreover, admittance spectroscopy indicates the presence of mid‐bandgap defects that are tentatively attributed to a Sn deficit in the film. In order to reduce the number of these deep defects within the active layer of our solar cells, the Sn content is tuned in the precursor ink. Their morphology, elemental composition, crystal phases, capacitance–voltage profiling, admittance, photoluminescence, and photovoltaic performances are characterized. The results indicate that tuning the Sn content offers a strong leverage upon some key properties of the active layer, in particular the grain size, and the charge carrier and defect density. By employing this leverage to optimize the performance of our CZTSSe layers, the cell performances are increased to 10.0% without antireflection coating (ARC) and to 10.8% (on 0.25 cm2) with an ARC.
- 15 October 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (24) , 1501404
Fine‐Tuning the Sn Content in CZTSSe Thin Films to Achieve 10.8% Solar Cell Efficiency from Spray‐Deposited Water–Ethanol‐Based Colloidal Inks
Thin film solar cells with Al/ITO/ZnO/CdS/CZTSSe/Mo‐glass structure are fabricated employing a fast and low‐cost preparation procedure using an aqueous ink deposited by nonpyrolytic spray, followed by high temperature crystallization and selenization steps. Capacitance–voltage measurements on previously reported devices with >8% efficiency under 1 sun irradiation show a charge carrier density of the order of 1017 cm−3. Moreover, admittance spectroscopy indicates the presence of mid‐bandgap defects that are tentatively attributed to a Sn deficit in the film. In order to reduce the number of these deep defects within the active layer of our solar cells, the Sn content is tuned in the precursor ink. Their morphology, elemental composition, crystal phases, capacitance–voltage profiling, admittance, photoluminescence, and photovoltaic performances are characterized. The results indicate that tuning the Sn content offers a strong leverage upon some key properties of the active layer, in particular the grain size, and the charge carrier and defect density. By employing this leverage to optimize the performance of our CZTSSe layers, the cell performances are increased to 10.0% without antireflection coating (ARC) and to 10.8% (on 0.25 cm2) with an ARC.
- 16 October 2014
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 5 (21) , 3763-3767
8.6% Efficient CZTSSe Solar Cells Sprayed from Water–Ethanol CZTS Colloidal Solutions
Copper zinc tin sulfide-selenide, Cu2ZnSn(S1–xSex)4 (CZTSSe), thin film photovoltaic devices were fabricated using a fast and environmentally friendly preparation method, consisting of the following steps: An instantaneous synthesis of a Cu–Zn–Sn–S (no Se) colloid, a nonpyrolytic spray of a dispersion of this colloid in a water–ethanol mixture, and a sequential annealing first in a N2 atmosphere and second in a Se atmosphere. The achievement of cell efficiencies up to 8.6% under AM1.5G (cell area 0.25 cm2) and without antireflecting coating indicates that this method can compete with other vacuum-based or more complex wet deposition methods.
- 16 October 2014
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 5 (21) , 3763-3767
8.6% Efficient CZTSSe Solar Cells Sprayed from Water–Ethanol CZTS Colloidal Solutions
Copper zinc tin sulfide-selenide, Cu2ZnSn(S1–xSex)4 (CZTSSe), thin film photovoltaic devices were fabricated using a fast and environmentally friendly preparation method, consisting of the following steps: An instantaneous synthesis of a Cu–Zn–Sn–S (no Se) colloid, a nonpyrolytic spray of a dispersion of this colloid in a water–ethanol mixture, and a sequential annealing first in a N2 atmosphere and second in a Se atmosphere. The achievement of cell efficiencies up to 8.6% under AM1.5G (cell area 0.25 cm2) and without antireflecting coating indicates that this method can compete with other vacuum-based or more complex wet deposition methods.
- 11 March 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (28) , 14655-14662
Efficient Cu2ZnSnS4solar cells spray coated from a hydro-alcoholic colloid synthesized by instantaneous reaction
Efficient copper zinc tin sulphide (Cu2ZnSnS4) thin film photovoltaic devices were fabricated with a new, fast, and simple preparation method using environmentally friendly solvents. Our process is based upon a versatile and instantaneous synthesis of a Cu–Zn–Sn–S colloid. Dispersing this colloid in a mixture of water (90%) and ethanol (10%), spraying it, and annealing sequentially the samples in two different gases allowed us to grow large grain, crystalline layers of promising photovoltaic quality. We measured cell efficiencies up to 5.0% under simulated AM1.5G (cell area 0.25 cm2). To the best of our knowledge, this is the highest reported efficiency reached with Cu2ZnSnS4 using a spray deposition technique with innocuous solvents.
- 11 March 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (28) , 14655-14662
Efficient Cu2ZnSnS4solar cells spray coated from a hydro-alcoholic colloid synthesized by instantaneous reaction
Efficient copper zinc tin sulphide (Cu2ZnSnS4) thin film photovoltaic devices were fabricated with a new, fast, and simple preparation method using environmentally friendly solvents. Our process is based upon a versatile and instantaneous synthesis of a Cu–Zn–Sn–S colloid. Dispersing this colloid in a mixture of water (90%) and ethanol (10%), spraying it, and annealing sequentially the samples in two different gases allowed us to grow large grain, crystalline layers of promising photovoltaic quality. We measured cell efficiencies up to 5.0% under simulated AM1.5G (cell area 0.25 cm2). To the best of our knowledge, this is the highest reported efficiency reached with Cu2ZnSnS4 using a spray deposition technique with innocuous solvents.