Hua Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hua Zhou has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Yinglong Chen
Naval Architecture and Ocean Engineering, Dalian Maritime University, Dalian, China
3 shared publications Peng-Yu Zhao
Zhejiang University
2 shared publications- Anhuan Xie
State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou 310027, China
1 shared publication Feng Yu
China Shipbuilding Industry Corporation (CSIC) 707 Institute
1 shared publicationHua-Yong Yang
Zhejiang University
1 shared publication- Huayong Yang
State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou 310027, China
1 shared publication
Latest Publications
- 1 January 2019
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 55 (24) , 216-226
Research Status of Active Control of Hydraulic Fluid Pulsation
- 1 January 2019
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 55 (24) , 216-226
Research Status of Active Control of Hydraulic Fluid Pulsation
- 11 November 2017
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 18 (11) , 1575-1589
Simulation analysis of potential energy recovery system of hydraulic hybrid excavator
- 11 November 2017
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 18 (11) , 1575-1589
Simulation analysis of potential energy recovery system of hydraulic hybrid excavator
- Open Access
- 8 November 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (11) , 1148
Theoretical Analysis for the Flow Ripple of a Tandem Crescent Pump with Index Angles
This paper presents a theoretical approach for lowering the outlet flow ripple of a crescent pump by applying a tandem crescent pump consisting of two gear pairs with an index angle between them. The outlet flow of the tandem pump is obtained by summing the flow produced by the two gear pairs, and the flow ripple of the tandem pump can be attenuated by properly selecting the design parameters in terms of the index angle and the displacement ratio between the two gear pairs. A lumped parameter model is presented for evaluating the crescent pump’s flow ripples, and experiments were performed on a single crescent pump to validate the model from the aspects of the steady-state flow-pressure characteristics and the outlet pressure ripples. In this way, the main causes of the flow ripple could be identified by comparing the kinematic flow with the actual flow evaluated by the model. Additionally, simulation results suggested that a tandem pump with an index angle of 13.85° and displacement ratio of 0.5 could lead to a more than 45% decrease in the outlet flow ripple than a single pump with the same displacement in a wide range of operating conditions.
- 8 November 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (11) , 1148
Open AccessTheoretical Analysis for the Flow Ripple of a Tandem Crescent Pump with Index Angles
This paper presents a theoretical approach for lowering the outlet flow ripple of a crescent pump by applying a tandem crescent pump consisting of two gear pairs with an index angle between them. The outlet flow of the tandem pump is obtained by summing the flow produced by the two gear pairs, and the flow ripple of the tandem pump can be attenuated by properly selecting the design parameters in terms of the index angle and the displacement ratio between the two gear pairs. A lumped parameter model is presented for evaluating the crescent pump’s flow ripples, and experiments were performed on a single crescent pump to validate the model from the aspects of the steady-state flow-pressure characteristics and the outlet pressure ripples. In this way, the main causes of the flow ripple could be identified by comparing the kinematic flow with the actual flow evaluated by the model. Additionally, simulation results suggested that a tandem pump with an index angle of 13.85° and displacement ratio of 0.5 could lead to a more than 45% decrease in the outlet flow ripple than a single pump with the same displacement in a wide range of operating conditions.
- 25 September 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 232 (8) , 983-994
Fuzzy logic control for a hydraulic hybrid excavator based on torque prediction and genetic algorithm optimization
Optimization of the control strategy, whose primary mission is to solve the problem associated with energy management, is an effective way to minimize the fuel consumption of the hydraulic hybrid excavator. As a widely used control strategy, fuzzy logic control can be adopted to realize suboptimal power split with robustness and adaptation, which is one of the most logical approaches for multidomain, nonlinear and time-varying plant. However, the membership functions are difficult to determine according to manual experiences; meanwhile, the optimization-based membership functions are difficult to utilize in real time control. This paper aims to improve the fuel consumption of a hydraulic hybrid excavator by proposing a fuzzy control strategy whose membership functions are optimized by the genetic algorithm, which considers predicted torque of the internal combustion engine (ICE) as a known quantity to realize real time control. The needed torque of the ICE is predicted by superposition of the previous torque. A fuzzy logic control strategy is then designed with membership functions optimized by the genetic algorithm according to the predicted needed torque to achieve better performance. Finally, a numerical experiment is carried out to verify the proposed control strategy.
- 25 September 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 232 (8) , 983-994
Fuzzy logic control for a hydraulic hybrid excavator based on torque prediction and genetic algorithm optimization
Optimization of the control strategy, whose primary mission is to solve the problem associated with energy management, is an effective way to minimize the fuel consumption of the hydraulic hybrid excavator. As a widely used control strategy, fuzzy logic control can be adopted to realize suboptimal power split with robustness and adaptation, which is one of the most logical approaches for multidomain, nonlinear and time-varying plant. However, the membership functions are difficult to determine according to manual experiences; meanwhile, the optimization-based membership functions are difficult to utilize in real time control. This paper aims to improve the fuel consumption of a hydraulic hybrid excavator by proposing a fuzzy control strategy whose membership functions are optimized by the genetic algorithm, which considers predicted torque of the internal combustion engine (ICE) as a known quantity to realize real time control. The needed torque of the ICE is predicted by superposition of the previous torque. A fuzzy logic control strategy is then designed with membership functions optimized by the genetic algorithm according to the predicted needed torque to achieve better performance. Finally, a numerical experiment is carried out to verify the proposed control strategy.
- 25 July 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 232 (12) , 2297-2314
Numerical analysis of the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps
Water hydraulics has drawn considerable attention in recent years for its environmental friendliness. This paper presents a numerical model for analysing the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps. The model consists of two parts: the gear part that addresses the radial force on the gear shaft and the film part that addresses the film characteristics of the gear shaft/journal bearing interface. The radial force is obtained by summing the fluid pressure around the gear circumference and the meshing force of the gear pair. The film characteristics are analysed by an elastohydrodynamic model that involves the evaluation of the film geometry, the film pressure, and the elastic deformation of the gear shaft/journal bearing interface. The radial force evaluated by the gear part is balanced by the film pressure evaluated by the film part. The gear part is validated by experiments on an oil internal gear pump from the aspect of the outlet pressure ripple, and the film part is validated by comparison with the results from other research groups. The proposed model allows the evaluation of radial micro-motion as well as the eccentric positions of the gear shaft. In addition, the influence of film deformation is further discussed, suggesting that the maximum film deformation should be maintained under 1.3 times the minimum film height. The proposed model can be used as a tool for design optimization of the water-lubricated journal bearing in water hydraulic internal gear pumps.
- 25 July 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 232 (12) , 2297-2314
Numerical analysis of the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps
Water hydraulics has drawn considerable attention in recent years for its environmental friendliness. This paper presents a numerical model for analysing the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps. The model consists of two parts: the gear part that addresses the radial force on the gear shaft and the film part that addresses the film characteristics of the gear shaft/journal bearing interface. The radial force is obtained by summing the fluid pressure around the gear circumference and the meshing force of the gear pair. The film characteristics are analysed by an elastohydrodynamic model that involves the evaluation of the film geometry, the film pressure, and the elastic deformation of the gear shaft/journal bearing interface. The radial force evaluated by the gear part is balanced by the film pressure evaluated by the film part. The gear part is validated by experiments on an oil internal gear pump from the aspect of the outlet pressure ripple, and the film part is validated by comparison with the results from other research groups. The proposed model allows the evaluation of radial micro-motion as well as the eccentric positions of the gear shaft. In addition, the influence of film deformation is further discussed, suggesting that the maximum film deformation should be maintained under 1.3 times the minimum film height. The proposed model can be used as a tool for design optimization of the water-lubricated journal bearing in water hydraulic internal gear pumps.
- 15 November 2014
- Published by Springer Nature in Journal of Central South University
- Vol. 21 (11) , 4172-4183
Effective model based fault detection scheme for rudder servo system
- 15 November 2014
- Published by Springer Nature in Journal of Central South University
- Vol. 21 (11) , 4172-4183
Effective model based fault detection scheme for rudder servo system
- 23 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 227 (8) , 1776-1790
Design of the conjugated straight-line internal gear pairs for fluid power gear machines
The conjugated straight-line internal gear pair, including a pinion with straight-line profile and an internal gear with profile conjugated to the pinion profile, is the key components to the conjugated straight-line internal gear pumps. Truninger [Truninger gear pump. Patent 3491698, USA, 1970] pointed that this kind of gear pairs leads to a very small trapped volume, which is 10 times smaller than that of the conventional involute internal gear pumps. Therefore, it can yield significant reduction in noise levels of the pumps. However, to the authors’ knowledge, there is no research on the design of these gear pairs until now. First, our study describes the straight-line profile of the pinion mathematically with definitions of some geometric parameters. Second, according to the theory of gearing, the mathematical models of the rack-cutter and the conjugated internal gear are derived. Then, the condition to avoid overcutting is obtained for the generation of the pinion by a rack-cutter. Finally, the condition to avoid interference in the internal gear pair is derived as a non-linear equation system and an algorithm is developed to find a numerical solution. Two examples are presented to demonstrate how to determine tooth numbers of the internal gears for avoiding interference. It is hoped that the study in this article should be helpful to the designers of the conjugated straight-line internal gear pairs. Moreover, it could provide a prepared knowledge for the researchers to investigate the performances of the fluid power gear machines, pumps, and motors, with the conjugated straight-line internal gear pumps.
- 23 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 227 (8) , 1776-1790
Design of the conjugated straight-line internal gear pairs for fluid power gear machines
The conjugated straight-line internal gear pair, including a pinion with straight-line profile and an internal gear with profile conjugated to the pinion profile, is the key components to the conjugated straight-line internal gear pumps. Truninger [Truninger gear pump. Patent 3491698, USA, 1970] pointed that this kind of gear pairs leads to a very small trapped volume, which is 10 times smaller than that of the conventional involute internal gear pumps. Therefore, it can yield significant reduction in noise levels of the pumps. However, to the authors’ knowledge, there is no research on the design of these gear pairs until now. First, our study describes the straight-line profile of the pinion mathematically with definitions of some geometric parameters. Second, according to the theory of gearing, the mathematical models of the rack-cutter and the conjugated internal gear are derived. Then, the condition to avoid overcutting is obtained for the generation of the pinion by a rack-cutter. Finally, the condition to avoid interference in the internal gear pair is derived as a non-linear equation system and an algorithm is developed to find a numerical solution. Two examples are presented to demonstrate how to determine tooth numbers of the internal gears for avoiding interference. It is hoped that the study in this article should be helpful to the designers of the conjugated straight-line internal gear pairs. Moreover, it could provide a prepared knowledge for the researchers to investigate the performances of the fluid power gear machines, pumps, and motors, with the conjugated straight-line internal gear pumps.