Michael Somerville
Research Subjects
Research Interests
Michael Somerville has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
Nawshad Haque
CSIRO Mineral Resources Flagship
3 shared publicationsSharif Jahanshahi
3 shared publications- Sharif Jahanshahi
CSIRO Minerals Down Under National Research Flagship
3 shared publications Yuhua Pan
CSIRO Mineral Resources, Clayton, Australia
3 shared publicationsA. Deev
2 shared publicationsChunlin Chen
CSIRO Mineral Resources
2 shared publications
Latest Publications
- Open Access
Deportment of Metals from E-Waste PCBs towards Alloy and Slag Phases during Smelting Using CaO-Al2O3-SiO2-B2O3 Slags
Printed circuit boards (PCBs) from antiquated electronic goods were processed by a pyrometallurgical route to produce and separate alloy and slag phases. The process involved initial size reduction of PCBs, followed by pyrolysis at 500 °C for 6 h and finally smelting of the solid materials in an electric furnace. A preliminary smelting test was performed at 1600 °C to estimate the composition of the slag generated. In later kilogram-scale smelting experiments, B2O3 flux was added along with CaO and SiO2 to decrease the liquidus temperature required to smelt the PCBs. The level of fluxing was adapted from earlier phase equilibria studies of the CaO-Al2O3-SiO2-B2O3 slag system. Results showed that the flux decreased the melting temperature and assisted the recovery of most valuable metals within the alloy phase at 1350 °C smelting temperature. The alloy phase recovered 99.8% of Cu, 99% of Sn, and 100% of precious metals (Au, Ag, Pt). A fluxing strategy for smelting high Al2O3 containing e-waste PCBs was proposed based on the experimental findings of this research.
Open AccessDeportment of Metals from E-Waste PCBs towards Alloy and Slag Phases during Smelting Using CaO-Al2O3-SiO2-B2O3 Slags
Printed circuit boards (PCBs) from antiquated electronic goods were processed by a pyrometallurgical route to produce and separate alloy and slag phases. The process involved initial size reduction of PCBs, followed by pyrolysis at 500 °C for 6 h and finally smelting of the solid materials in an electric furnace. A preliminary smelting test was performed at 1600 °C to estimate the composition of the slag generated. In later kilogram-scale smelting experiments, B2O3 flux was added along with CaO and SiO2 to decrease the liquidus temperature required to smelt the PCBs. The level of fluxing was adapted from earlier phase equilibria studies of the CaO-Al2O3-SiO2-B2O3 slag system. Results showed that the flux decreased the melting temperature and assisted the recovery of most valuable metals within the alloy phase at 1350 °C smelting temperature. The alloy phase recovered 99.8% of Cu, 99% of Sn, and 100% of precious metals (Au, Ag, Pt). A fluxing strategy for smelting high Al2O3 containing e-waste PCBs was proposed based on the experimental findings of this research.
- 29 September 2021
- Published by SAGE Publications in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy
- Vol. 131 (3) , 271-282
Measurement and physical model prediction on splash fluxes in a pilot TSL bath smelting furnace
Top Submerged Lance (TSL) furnaces used for non-ferrous smelting have high heat and mass transfer rates due to the intensive stirring and splashing generated by the lance. While splashing can cause accretion build-up in the upper cooler regions of the furnace, it plays an important role in heat and mass transfer and needs to be controlled to minimise accretion formations while maximising furnace productivity. In this work, splashing was studied by measuring the splash flux from a molten slag bath in a 300 kg pilot-scale TSL furnace and also from an ambient temperature aqueous-glycerol solution bath in a physical model. In both systems, total injection gas flowrate, lance immersion depth and splash height were examined to determine their effects on the splash flux. An empirical correlation was developed based on the results of the aqueous-glycerol physical model using the methodology of dimensional analysis. This correlation was then used to predict the splash for high temperature smelting conditions. Comparison of the predictions with both hot and cold experimental measurements showed the same variation trends and the predicted values were within an acceptable range, particularly in splash heights within 1 m above the bath surface and at medium to high gas flowrates with lance immersion depths being 1/6–1/3 of the bath height. It is concluded that the correlation can be potentially applied to predict splashing behaviour in TSL furnaces.
- 29 September 2021
- Published by SAGE Publications in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy
- Vol. 131 (3) , 271-282
Measurement and physical model prediction on splash fluxes in a pilot TSL bath smelting furnace
Top Submerged Lance (TSL) furnaces used for non-ferrous smelting have high heat and mass transfer rates due to the intensive stirring and splashing generated by the lance. While splashing can cause accretion build-up in the upper cooler regions of the furnace, it plays an important role in heat and mass transfer and needs to be controlled to minimise accretion formations while maximising furnace productivity. In this work, splashing was studied by measuring the splash flux from a molten slag bath in a 300 kg pilot-scale TSL furnace and also from an ambient temperature aqueous-glycerol solution bath in a physical model. In both systems, total injection gas flowrate, lance immersion depth and splash height were examined to determine their effects on the splash flux. An empirical correlation was developed based on the results of the aqueous-glycerol physical model using the methodology of dimensional analysis. This correlation was then used to predict the splash for high temperature smelting conditions. Comparison of the predictions with both hot and cold experimental measurements showed the same variation trends and the predicted values were within an acceptable range, particularly in splash heights within 1 m above the bath surface and at medium to high gas flowrates with lance immersion depths being 1/6–1/3 of the bath height. It is concluded that the correlation can be potentially applied to predict splashing behaviour in TSL furnaces.
- 1 May 2020
- Published by Elsevier in Renewable Energy
- Vol. 151, 419-425
The effect of heating rate, particle size and gas flow on the yield of charcoal during the pyrolysis of radiata pine wood
- 1 May 2020
- Published by Elsevier in Renewable Energy
- Vol. 151, 419-425
The effect of heating rate, particle size and gas flow on the yield of charcoal during the pyrolysis of radiata pine wood
- 9 February 2017
- Published by Springer Nature
- p. 261-267
Direct-to-Blister Copper Smelting with the ISASMELT™ Process
- 9 February 2017
- Published by Springer Nature
- p. 261-267
Direct-to-Blister Copper Smelting with the ISASMELT™ Process
- 5 December 2016
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 3 (3) , 486-494
Liquidus- and Primary-Phase Determinations of Slags Used in the Processing of Spent Pot Lining
- 5 December 2016
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 3 (3) , 486-494
Liquidus- and Primary-Phase Determinations of Slags Used in the Processing of Spent Pot Lining
- 16 May 2016
- Published by Wiley
- p. 667-675
Fluxing Strategies for the Direct to Blister Smelting of High Silica and Low Iron Copper Concentrates
- 16 May 2016
- Published by Wiley
- p. 667-675
Fluxing Strategies for the Direct to Blister Smelting of High Silica and Low Iron Copper Concentrates
- 5 May 2016
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 2 (3) , 228-238
The Strength and Density of Green and Reduced Briquettes Made with Iron Ore and Charcoal
- 5 May 2016
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 2 (3) , 228-238
The Strength and Density of Green and Reduced Briquettes Made with Iron Ore and Charcoal
- 2 February 2016
- Published by Wiley
- p. 297-302
Hightemperature Characterisation and Technoeconomics of E‐Waste Processing
- 2 February 2016
- Published by Wiley
- p. 297-302
Hightemperature Characterisation and Technoeconomics of E‐Waste Processing
- Open Access
- 28 September 2015
- Published by David Publishing Company in Journal of Mechanics Engineering and Automation
- Vol. 5 (9)
Mathematical Model Prediction of Heat Losses from a Pilot Sirosmelt Furnace
- 28 September 2015
- Published by David Publishing Company in Journal of Mechanics Engineering and Automation
- Vol. 5 (9)
Open AccessMathematical Model Prediction of Heat Losses from a Pilot Sirosmelt Furnace
- 1 August 2015
- Published by Elsevier in Renewable Energy
- Vol. 80, 471-478
The effect of temperature and compression during pyrolysis on the density of charcoal made from Australian eucalypt wood
- 1 August 2015
- Published by Elsevier in Renewable Energy
- Vol. 80, 471-478
The effect of temperature and compression during pyrolysis on the density of charcoal made from Australian eucalypt wood