Auttasit Tubtimtae
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Auttasit Tubtimtae has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Ekasiddh Wongrat
13 shared publicationsPhathaitep Raksa
6 shared publications- Supab Choopun
Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200, Thailand
6 shared publications Prayoonsak Pluengphon
5 shared publicationsPanupat Chaiworn
4 shared publicationsKritsada Hongsith
Department of Physics and Material Sciences, Faculty of Science, Chiang Mai University, Chiang Mai 50200, Thailand; Thailand Center of Excellence in Physics (ThEP Center), CHE, Bangkok 10400, Thailand
3 shared publications
Latest Publications
- 25 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 17905-17924
Impact of potassium doping on the physical properties of cadmium sulfide thin films prepared by sol-gel screen printing technique
- 25 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 17905-17924
Impact of potassium doping on the physical properties of cadmium sulfide thin films prepared by sol-gel screen printing technique
- 12 September 2025
- Published by Elsevier in Optical Materials
- Vol. 168
Effect of antimony oxide incorporation on the structural, optical, and electrical properties of multiphase bismuth telluride thin films
- 12 September 2025
- Published by Elsevier in Optical Materials
- Vol. 168
Effect of antimony oxide incorporation on the structural, optical, and electrical properties of multiphase bismuth telluride thin films
- 6 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 18786-18798
Structural, optical, electrical, and gas sensing properties of antimony-doped selenium dioxide thin films synthesized using spray pyrolysis method
- 6 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 18786-18798
Structural, optical, electrical, and gas sensing properties of antimony-doped selenium dioxide thin films synthesized using spray pyrolysis method
- 30 September 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (11) , 115012
Aluminum antimony alloy overlayers synthesized using the electrodeposition method: investigation of structural, optical, electrical properties, and DFT calculation
This paper presents the synthesis of aluminum antimony (Al–Sb) alloy overlayers using an electrodeposition method for application in optoelectronic devices with various applied constant voltages (2, 4, 6, 8, and 10 V) controlled by a DC power supply. The corresponding energy dispersive x-ray spectroscope spectra show that elements including Al, Sb, and Cl were detected in the layers under all conditions of the applied voltage. The structural properties of the formulated compound layers were studied for their structural properties through x-ray diffraction patterns, and all the diffraction peaks exhibited a cubic phase structure. The Al–Sb alloy overlayers were incorporated with nanoparticles and had crystallite sizes ranging from ∼55 to 282 nm. The average transmittance T(λ) values in the visible to near-infrared region were ∼28.36%, 17.64%, 14.07%, 7.83%, and 5.84%, while the average reflectance R(λ) values were ∼3.80%, 1.69%, 1.30%, 0.47%, and 0.21% for applied voltages of 2–10 V, respectively. The energy band gap (E g) existing in the overlayers was determined using Tauc’s plot with the Kubelka–Munk function and it was inferred to be between 1.90 eV and 2.72 eV. The dispersion constants and energies of the prepared samples were also investigated. The 2 V applied voltage-treated Al–Sb alloy overlayers showed the highest average χ(1), χ ( 3 ) , and n 2 values of 0.088, 1.680 × 10−14 esu., and 4.082 × 10−13 esu., respectively. In addition, the resistance at various absolute temperatures was also recorded for the activation energy (E AC) values of the Al–Sb alloy overlayers with applied voltages of 2–10 V. Finally, ab initio calculations based on density functional theory were performed to support the experimental report of the Al–Sb systems. It was found that the calculated lattice constants are in good agreement with the experimental results, and a wider photoabsorption range performance for Al–Sb phase I in the axis of energy seems to be suitable for application as an optical device.
- 30 September 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (11) , 115012
Aluminum antimony alloy overlayers synthesized using the electrodeposition method: investigation of structural, optical, electrical properties, and DFT calculation
This paper presents the synthesis of aluminum antimony (Al–Sb) alloy overlayers using an electrodeposition method for application in optoelectronic devices with various applied constant voltages (2, 4, 6, 8, and 10 V) controlled by a DC power supply. The corresponding energy dispersive x-ray spectroscope spectra show that elements including Al, Sb, and Cl were detected in the layers under all conditions of the applied voltage. The structural properties of the formulated compound layers were studied for their structural properties through x-ray diffraction patterns, and all the diffraction peaks exhibited a cubic phase structure. The Al–Sb alloy overlayers were incorporated with nanoparticles and had crystallite sizes ranging from ∼55 to 282 nm. The average transmittance T(λ) values in the visible to near-infrared region were ∼28.36%, 17.64%, 14.07%, 7.83%, and 5.84%, while the average reflectance R(λ) values were ∼3.80%, 1.69%, 1.30%, 0.47%, and 0.21% for applied voltages of 2–10 V, respectively. The energy band gap (E g) existing in the overlayers was determined using Tauc’s plot with the Kubelka–Munk function and it was inferred to be between 1.90 eV and 2.72 eV. The dispersion constants and energies of the prepared samples were also investigated. The 2 V applied voltage-treated Al–Sb alloy overlayers showed the highest average χ(1), χ ( 3 ) , and n 2 values of 0.088, 1.680 × 10−14 esu., and 4.082 × 10−13 esu., respectively. In addition, the resistance at various absolute temperatures was also recorded for the activation energy (E AC) values of the Al–Sb alloy overlayers with applied voltages of 2–10 V. Finally, ab initio calculations based on density functional theory were performed to support the experimental report of the Al–Sb systems. It was found that the calculated lattice constants are in good agreement with the experimental results, and a wider photoabsorption range performance for Al–Sb phase I in the axis of energy seems to be suitable for application as an optical device.
- 29 July 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (8) , 1-18
Effects of Sn doping on the structural, optical, photoluminescence, and electrical properties of transparent SeO2 thin films
- 29 July 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (8) , 1-18
Effects of Sn doping on the structural, optical, photoluminescence, and electrical properties of transparent SeO2 thin films