Hua-Ping Xiong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hua-Ping Xiong has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Bo Chen
Welding and Plastic Forming Division, Beijing Institute of Aeronautical Materials, Beijing, China
7 shared publicationsXinyu Ren
Welding and Plastic Forming Division, Beijing Institute of Aeronautical Materials, Beijing, People’s Republic of China
4 shared publicationsY. Y. Cheng
Welding and Plastic Forming Division, Beijing Institute of Aeronautical Materials, Beijing, China
4 shared publicationsB. Chen
Beijing Institute of Aeronautical Materials
3 shared publicationsH. S. Ren
Welding and Plastic Forming Division, Beijing Institute of Aeronautical Materials, Beijing, China
3 shared publicationsWenwen Li
Welding and Plastic Forming Division, Beijing Institute of Aeronautical Materials, Beijing, China
3 shared publications
Latest Publications
- 25 May 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (9) , 2511-2520
Microstructures and mechanical properties of TiAl joint brazed with Ti-Mn-Fe-Ni-Zr system medium-entropy filler alloy
- 25 May 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (9) , 2511-2520
Microstructures and mechanical properties of TiAl joint brazed with Ti-Mn-Fe-Ni-Zr system medium-entropy filler alloy
- Open Access
- 26 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 1677-1686
Deformation behavior and microstructure characterization of A357 aluminum alloy welding wires used for wire arc additive manufacturing
- 26 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 1677-1686
Open AccessDeformation behavior and microstructure characterization of A357 aluminum alloy welding wires used for wire arc additive manufacturing
- 12 February 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (4) , 939-951
Effect of solution heat treatment on the microstructure and mechanical properties of laser melting deposited GH 5188 superalloy
- 12 February 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (4) , 939-951
Effect of solution heat treatment on the microstructure and mechanical properties of laser melting deposited GH 5188 superalloy
- Open Access
Chemical Composition, Microstructure, Tensile and Creep Behavior of Ti60 Alloy Fabricated via Electron Beam Directed Energy Deposition
Electron beam directed energy deposition (EB-DED) is a promising manufacturing process for the fabrication of large-scale, fully dense and near net shape metallic components. However, limited knowledge is available on the EB-DED process of titanium alloys. In this study, a near-α high-temperature titanium alloy Ti60 (Ti-5.8Al-4Sn-4Zr-0.7Nb-1.5Ta-0.4Si) was fabricated via EB-DED. The chemical composition, microstructure, tensile property (at room temperature and 600 °C), and creep behavior of the fabricated alloy were investigated and compared with those of the conventional wrought lamellar and bimodal counterparts. Results indicated that the average evaporation loss of Al and Sn was 10.28% and 5.01%, respectively. The microstructure of the as-built alloy was characterized by coarse columnar grains, lamellar α, and the precipitated elliptical silicides at the α/β interfaces. In terms of tensile properties, the vertical specimens exhibited lower strength but higher ductility than the horizontal specimens at both room temperature and 600 °C. Furthermore, the tensile creep strain of the EB-DED Ti60 alloy measured at 600 °C and 150 MPa for 100 h under as-built and post-deposition STA conditions was less than 0.15%, which meets the standard requirements for the wrought Ti60 alloy. The creep resistance of the EB-DED Ti60 alloy was superior to that of its wrought bimodal counterpart.
Open AccessChemical Composition, Microstructure, Tensile and Creep Behavior of Ti60 Alloy Fabricated via Electron Beam Directed Energy Deposition
Electron beam directed energy deposition (EB-DED) is a promising manufacturing process for the fabrication of large-scale, fully dense and near net shape metallic components. However, limited knowledge is available on the EB-DED process of titanium alloys. In this study, a near-α high-temperature titanium alloy Ti60 (Ti-5.8Al-4Sn-4Zr-0.7Nb-1.5Ta-0.4Si) was fabricated via EB-DED. The chemical composition, microstructure, tensile property (at room temperature and 600 °C), and creep behavior of the fabricated alloy were investigated and compared with those of the conventional wrought lamellar and bimodal counterparts. Results indicated that the average evaporation loss of Al and Sn was 10.28% and 5.01%, respectively. The microstructure of the as-built alloy was characterized by coarse columnar grains, lamellar α, and the precipitated elliptical silicides at the α/β interfaces. In terms of tensile properties, the vertical specimens exhibited lower strength but higher ductility than the horizontal specimens at both room temperature and 600 °C. Furthermore, the tensile creep strain of the EB-DED Ti60 alloy measured at 600 °C and 150 MPa for 100 h under as-built and post-deposition STA conditions was less than 0.15%, which meets the standard requirements for the wrought Ti60 alloy. The creep resistance of the EB-DED Ti60 alloy was superior to that of its wrought bimodal counterpart.
- 18 March 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (7) , 1437-1446
Effect of element Zr in Ti-Zr–Ni-Nb system brazing filler alloys on the microstructure and strength of TiAl/TiAl joints
- 18 March 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (7) , 1437-1446
Effect of element Zr in Ti-Zr–Ni-Nb system brazing filler alloys on the microstructure and strength of TiAl/TiAl joints
- 5 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (3) , 557-565
Joining of TiAl-based alloy and a Ni-based superalloy with a NiCoFeCuSiB high entropy filler metal
- 5 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (3) , 557-565
Joining of TiAl-based alloy and a Ni-based superalloy with a NiCoFeCuSiB high entropy filler metal
- 7 June 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (9) , 1767-1775
Dissimilar brazing of NbSS/Nb5Si3 composite to GH5188 superalloy using Ni-based filler alloys
- 7 June 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (9) , 1767-1775
Dissimilar brazing of NbSS/Nb5Si3 composite to GH5188 superalloy using Ni-based filler alloys
- 17 May 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (9) , 1759-1765
Joining of the SiCf/SiBCN composite with CoNiPdNbCr filler alloy and the control of the interfacial reactions
- 17 May 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (9) , 1759-1765
Joining of the SiCf/SiBCN composite with CoNiPdNbCr filler alloy and the control of the interfacial reactions
- Open Access
- 12 April 2021
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 34 (1) , 1-16
Laser Additive Manufacturing on Metal Matrix Composites: A Review
- 12 April 2021
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 34 (1) , 1-16
Open AccessLaser Additive Manufacturing on Metal Matrix Composites: A Review
- 3 January 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (4) , 713-719
Joining of Cf/SiC composite with Cu–Pd–V filler alloy and Mo interlayer
- 3 January 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (4) , 713-719
Joining of Cf/SiC composite with Cu–Pd–V filler alloy and Mo interlayer