Young Jin Mok
Research Subjects
Research Interests
Young Jin Mok has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Chul Soo Park
Korea Institute of Civil Engineering and Building Technology
2 shared publicationsHak Sung Kim
Research Assistant, Dept. of Civil Eng., Kyunghee University, Korea
2 shared publicationsIn Beom Park
Chunil Engineering Co., Ltd
2 shared publications- Jae Woo Jung
Research Assistant, Dept. of Civil Eng., Kyunghee Univ., Korea
2 shared publications - Chul Soo Park
Korea Institute of Civil Engineering and Building Technology
1 shared publication - Chul Soo Park
Research Assistant, Dept. of Civil Eng., Kyunghee University, Korea
1 shared publication
Latest Publications
- Open Access
- 1 May 2015
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 19 (4) , 911-916
S-wave cross-hole logging for stone columns
- 1 May 2015
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 19 (4) , 911-916
Open AccessS-wave cross-hole logging for stone columns
- Open Access
- 31 December 2014
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 19 (6) , 1647-1655
Evaluation of resilient moduli for recycled crushed-rock-soil-mixtures using in-situ seismic techniques and large-scale resonant column tests
- 31 December 2014
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 19 (6) , 1647-1655
Open AccessEvaluation of resilient moduli for recycled crushed-rock-soil-mixtures using in-situ seismic techniques and large-scale resonant column tests
- 13 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 77-82
Logging for Diametric Variation of Stone Columns Using Crosshole Seismic Tests
An integrity testing for stone columns was attempted using crosshole S-wave logging. The method is conceptionally quite similar to the crosshole sonic logging (CSL) for drilled piers. The critical difference in the logging is the use of s-wave rather than p-wave, which is used in CSL, because s-wave is the only wave sensing the stiffness of slower unbounded materials than water. An electro-mechanical source, which can generate reversed S-wave signals, was utilized in the logging. The stone column was delineated from the S-wave travel times across the stone column, and taking S-wave velocities of the crushed stone and surrounding soil into account. The volume calculated from the diametrical variance delineated is very close to the actual quantity of the stone filled.
- 13 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 77-82
Logging for Diametric Variation of Stone Columns Using Crosshole Seismic Tests
An integrity testing for stone columns was attempted using crosshole S-wave logging. The method is conceptionally quite similar to the crosshole sonic logging (CSL) for drilled piers. The critical difference in the logging is the use of s-wave rather than p-wave, which is used in CSL, because s-wave is the only wave sensing the stiffness of slower unbounded materials than water. An electro-mechanical source, which can generate reversed S-wave signals, was utilized in the logging. The stone column was delineated from the S-wave travel times across the stone column, and taking S-wave velocities of the crushed stone and surrounding soil into account. The volume calculated from the diametrical variance delineated is very close to the actual quantity of the stone filled.
- 13 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 83-88
Estimating Field Properties of Soft Soil Using Penetration-Type S-Wave Probe
A new s-wave probe, called "MudFork", has been recently developed and is used in accurate measurements of shear wave velocities of soft soils. The probe is composed of two bender elements mounted on a "fork" having two blades, one element perturbing ground and the other one monitoring seismic waves, and can be penetrated using SPT(standard penetration test) rods pushed with a routine boring machine. To expand its use to estimate undrained shear strength and density, an attempt to correlate shear wave velocity to those properties was made at normally consolidated silt near Incheon, Korea. A simple linear relationship between shear strength and shear wave velocity was obtained, and a tentative relationship between density and shear wave velocity was also defined.
- 13 July 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 83-88
Estimating Field Properties of Soft Soil Using Penetration-Type S-Wave Probe
A new s-wave probe, called "MudFork", has been recently developed and is used in accurate measurements of shear wave velocities of soft soils. The probe is composed of two bender elements mounted on a "fork" having two blades, one element perturbing ground and the other one monitoring seismic waves, and can be penetrated using SPT(standard penetration test) rods pushed with a routine boring machine. To expand its use to estimate undrained shear strength and density, an attempt to correlate shear wave velocity to those properties was made at normally consolidated silt near Incheon, Korea. A simple linear relationship between shear strength and shear wave velocity was obtained, and a tentative relationship between density and shear wave velocity was also defined.
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Development and Applications of In-Hole Seismic Method to Measure Shear Wave Velocity of Subsurface Materials
The dynamic stiffness of the ground is one of the key parameters in earthquake-resistant designs involving local ground response and in assessment of geotechnical structures subjected to various man-made vibrations. Its use is being extended even to static settlement and deformation problems. Its importance and extended usage require a more manageable method than conventional seismic techniques such as crosshole, downhole test, and suspension logging. In general, conventional borehole seismic methods are expensive and technically complex. This paper presents a new method which has been developed to reduce testing cost and to improve the easiness in its use. An in-hole probe has been developed to be fit in three-inch boreholes with functional improvements including a pair of mechanical couplings driven with two servomotors, and a servomotor triggering device. The in-hole seismic method was adopted at various sites such as compaction fills of railroad subgrade, bedrocks of tunnel construction sites, tunnel-face rock mass, and abutment of rock fill dam. In-hole seismic test results were verified by comparing with reliable crosshole results. Presently, the method is very cost effective and easy to use in residual soils, compaction fills and bedrock where uncased boreholes can stay open.
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Development and Applications of In-Hole Seismic Method to Measure Shear Wave Velocity of Subsurface Materials
The dynamic stiffness of the ground is one of the key parameters in earthquake-resistant designs involving local ground response and in assessment of geotechnical structures subjected to various man-made vibrations. Its use is being extended even to static settlement and deformation problems. Its importance and extended usage require a more manageable method than conventional seismic techniques such as crosshole, downhole test, and suspension logging. In general, conventional borehole seismic methods are expensive and technically complex. This paper presents a new method which has been developed to reduce testing cost and to improve the easiness in its use. An in-hole probe has been developed to be fit in three-inch boreholes with functional improvements including a pair of mechanical couplings driven with two servomotors, and a servomotor triggering device. The in-hole seismic method was adopted at various sites such as compaction fills of railroad subgrade, bedrocks of tunnel construction sites, tunnel-face rock mass, and abutment of rock fill dam. In-hole seismic test results were verified by comparing with reliable crosshole results. Presently, the method is very cost effective and easy to use in residual soils, compaction fills and bedrock where uncased boreholes can stay open.
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Development of Buried Sensors for Stiffness Measurements of Soft Clays Using Bender Elements
The use of vertical drains, along with pre-loading, is the most popular method of soil improvement in coastal areas to meet growing demand for diverse uses of limited land space. Piezometers are the key instrument for continuous monitoring throughout the consolidation period. Basically, piezometers have several disadvantages such as incapability of providing any mechanical properties, meticulous installation procedures, misleading results caused by unexpected hydrogeologic boundary condition, and relatively high damage rate. As an alternative instrument for monitoring soil improvement, a piezo-electric sensor was elected to measure stiffness changes during consolidation. The piezo-electric sensor is composed of two bender elements mounted on a frame. Bender elements, composed of piezo-materials and metal shims, have favorable features suitable to field instrumentation such as simple principle of energy conversion, excellent control capability and small physical size. The prototype sensors have been developed through extensive in-house program to optimize in terms of data quality and installation convenience. The first prototype sensor was implemented in coastal mud using SPT(standard penetration test) rods pushed with a routine boring machine and excellent shear wave signals were measured. The sensor is on the further collective refining process.
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Development of Buried Sensors for Stiffness Measurements of Soft Clays Using Bender Elements
The use of vertical drains, along with pre-loading, is the most popular method of soil improvement in coastal areas to meet growing demand for diverse uses of limited land space. Piezometers are the key instrument for continuous monitoring throughout the consolidation period. Basically, piezometers have several disadvantages such as incapability of providing any mechanical properties, meticulous installation procedures, misleading results caused by unexpected hydrogeologic boundary condition, and relatively high damage rate. As an alternative instrument for monitoring soil improvement, a piezo-electric sensor was elected to measure stiffness changes during consolidation. The piezo-electric sensor is composed of two bender elements mounted on a frame. Bender elements, composed of piezo-materials and metal shims, have favorable features suitable to field instrumentation such as simple principle of energy conversion, excellent control capability and small physical size. The prototype sensors have been developed through extensive in-house program to optimize in terms of data quality and installation convenience. The first prototype sensor was implemented in coastal mud using SPT(standard penetration test) rods pushed with a routine boring machine and excellent shear wave signals were measured. The sensor is on the further collective refining process.