Yu. N. Pyrkov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yu. N. Pyrkov has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Vladimir B. Tsvetkov
Prokhorov General Physics Institute of the Russian Academy of Sciences, 38 Vavilov St., 119991 Moscow, Russia
6 shared publications - Vladimir F. Seregin
Russian Academy of Sciences
3 shared publications A I Trikshev
2 shared publications- Dmitriy S. Vakalov
Department of Physics and Technology of Nanostructures and Materials, Physical and Technical Faculty, North Caucasus Federal University, 355017 Stavropol, Russia
2 shared publications - Elena A. Dobretsova
Prokhorov General Physics Institute
2 shared publications - Irina Chikulina
Scientific and Laboratory Complex Clean Room, North Caucasus Federal University, 355029 Stavropol, Russia
2 shared publications
Latest Publications
- 27 October 2024
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 32 (5) , 354-359
Autocollimation Optical Doppler Velocimeter: Velocity Measurement of Hard-to-Access Objects
All-fiber autocollimation schemes of the laser Doppler velocimeter (LDV) are presented that enable measuring velocities of hard-to-access objects in the ra
- 27 October 2024
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 32 (5) , 354-359
Autocollimation Optical Doppler Velocimeter: Velocity Measurement of Hard-to-Access Objects
All-fiber autocollimation schemes of the laser Doppler velocimeter (LDV) are presented that enable measuring velocities of hard-to-access objects in the ra
- Open Access
- 11 October 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (10) , 170
Judd-Ofelt Analysis of High Erbium Content Yttrium-Aluminum and Yttrium-Scandium-Aluminum Garnet Ceramics
The Er1.5Y1.5Al5O12 (Er:YAG) and (Er1.43Y1.43Sc0.14)(Sc0.24Al1.76)Al3O12 (Er:YSAG) ceramics have been characterized using the Judd-Ofelt (JO) theory. The line strengths and oscillator strengths of several transitions from the ground state 4I15/2 to excited state manifolds have been evaluated from transmittance spectra measured at room temperature (300 K). The JO parameters have been calculated, and the values of the radiative decays rate and the radiative lifetimes for the 4I13/2 excited state, and the luminescence cross-section of 4I15/2 → 4I13/2 in Er-doped ceramic samples have been established. We have traced the influence of Sc3+ inclusion on spectroscopic properties and crystal quality and estimate prospects of application in laser systems.
- 11 October 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (10) , 170
Open AccessJudd-Ofelt Analysis of High Erbium Content Yttrium-Aluminum and Yttrium-Scandium-Aluminum Garnet Ceramics
The Er1.5Y1.5Al5O12 (Er:YAG) and (Er1.43Y1.43Sc0.14)(Sc0.24Al1.76)Al3O12 (Er:YSAG) ceramics have been characterized using the Judd-Ofelt (JO) theory. The line strengths and oscillator strengths of several transitions from the ground state 4I15/2 to excited state manifolds have been evaluated from transmittance spectra measured at room temperature (300 K). The JO parameters have been calculated, and the values of the radiative decays rate and the radiative lifetimes for the 4I13/2 excited state, and the luminescence cross-section of 4I15/2 → 4I13/2 in Er-doped ceramic samples have been established. We have traced the influence of Sc3+ inclusion on spectroscopic properties and crystal quality and estimate prospects of application in laser systems.
- Open Access
- 15 January 2022
- Published by MDPI AG in Chemistry Proceedings
- Vol. 9 (1) , 18
Fabrication and Characterization of New Er-Doped Yttrium–Scandium–Aluminum–Garnet Ceramics
We report the fabrication and characterization of yttrium–aluminum–garnet (Er:YAG) and yttrium–scandium–aluminum–garnet (Er:YSAG) ceramics for the implementation of analysis as an active medium for 1500 nm lasing. High erbium content Er:YAG and Er:YSAG ceramics are fabricated from Er:YAG and Er:YSAG powders, respectively. All ceramic samples belong to the garnet-type cubic structure (space group Ia3d) without any traceable impure phases. Including Sc3+ in the Er:YAG crystal structure leads to improved mechanical characteristics and elastic–plastic properties of the materials. The optical transmittance of ceramics is affected strongly by including Sc3+ and increases up to 60% at about 1500 nm.
- 15 January 2022
- Published by MDPI AG in Chemistry Proceedings
- Vol. 9 (1) , 18
Open AccessFabrication and Characterization of New Er-Doped Yttrium–Scandium–Aluminum–Garnet Ceramics
We report the fabrication and characterization of yttrium–aluminum–garnet (Er:YAG) and yttrium–scandium–aluminum–garnet (Er:YSAG) ceramics for the implementation of analysis as an active medium for 1500 nm lasing. High erbium content Er:YAG and Er:YSAG ceramics are fabricated from Er:YAG and Er:YSAG powders, respectively. All ceramic samples belong to the garnet-type cubic structure (space group Ia3d) without any traceable impure phases. Including Sc3+ in the Er:YAG crystal structure leads to improved mechanical characteristics and elastic–plastic properties of the materials. The optical transmittance of ceramics is affected strongly by including Sc3+ and increases up to 60% at about 1500 nm.
- 1 December 2017
- Published by Elsevier in Journal of Crystal Growth
- Vol. 480, 85-89
Temperature and emissivity measurements at the sapphire single crystal fiber growth process
- 1 December 2017
- Published by Elsevier in Journal of Crystal Growth
- Vol. 480, 85-89
Temperature and emissivity measurements at the sapphire single crystal fiber growth process
- 28 November 2017
- Published by IOP Publishing in Quantum Electronics
- Vol. 47 (11) , 1045-1048
Phasing of two amplifier channels for the coherent combining of laser beams with a total power of 60 W
We have demonstrated stable operation of a system for maintaining a constant phase difference between two laser channels with a total output power of 60 W. The system is based on a twochannel fibre amplifier with phase modulators based on piezoceramic spools. At a main piezo element modulation frequency of 11 kHz, the phasing time after thermal and mechanical influences on the active medium is 100 ms.
- 28 November 2017
- Published by IOP Publishing in Quantum Electronics
- Vol. 47 (11) , 1045-1048
Phasing of two amplifier channels for the coherent combining of laser beams with a total power of 60 W
We have demonstrated stable operation of a system for maintaining a constant phase difference between two laser channels with a total output power of 60 W. The system is based on a twochannel fibre amplifier with phase modulators based on piezoceramic spools. At a main piezo element modulation frequency of 11 kHz, the phasing time after thermal and mechanical influences on the active medium is 100 ms.
- 1 October 2014
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 22 (4) , 255-261
Method for measuring optical characteristics of opaque and translucent solids at temperatures to 1600°C
A setup is developed for measuring optical characteristics of opaque and translucent solids in the temperature range of 25 to 1600°C and spectral range of 0.65 to 10.6 µm. Procedures of calibration experiments and measurements of spectral and integral emissivity are described. These procedures allow spectral and integral emissivity and spectral and integral reflectances of various materials, including translucent ones, to be measured accurate to about 10% in the spectral range of 0.65 to 10,6 µm and temperature range of 25 to 1600°C. Optical characteristics of materials are measured at the atmospheric pressure in the normal oxygen atmosphere or in the atmosphere with reduced oxygen content (inert gas or carbon dioxide blowing on the frontal surface of the samples). The accuracy of the thus obtained data on temperature and spectrum dependences of optical characteristics of materials allow measurements to be performed for developing various structures capable of operating at high temperatures.
- 1 October 2014
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 22 (4) , 255-261
Method for measuring optical characteristics of opaque and translucent solids at temperatures to 1600°C
A setup is developed for measuring optical characteristics of opaque and translucent solids in the temperature range of 25 to 1600°C and spectral range of 0.65 to 10.6 µm. Procedures of calibration experiments and measurements of spectral and integral emissivity are described. These procedures allow spectral and integral emissivity and spectral and integral reflectances of various materials, including translucent ones, to be measured accurate to about 10% in the spectral range of 0.65 to 10,6 µm and temperature range of 25 to 1600°C. Optical characteristics of materials are measured at the atmospheric pressure in the normal oxygen atmosphere or in the atmosphere with reduced oxygen content (inert gas or carbon dioxide blowing on the frontal surface of the samples). The accuracy of the thus obtained data on temperature and spectrum dependences of optical characteristics of materials allow measurements to be performed for developing various structures capable of operating at high temperatures.
- 31 July 2011
- Published by IOP Publishing in Quantum Electronics
- Vol. 41 (7) , 656-658
Measurement of the emission linewidth of a single-frequency semiconductor laser with a ring fibre interferometer
- 31 July 2011
- Published by IOP Publishing in Quantum Electronics
- Vol. 41 (7) , 656-658
Measurement of the emission linewidth of a single-frequency semiconductor laser with a ring fibre interferometer